Question about 2001 Volkswagen Jetta TDI

1 Answer

Jetta 4 brakes

Changed front brake pads and disks. Now when I brake everything is fine but the last meter or so before the car stops, the padel pushes back and there is a buzzing sound in front.

Posted by on

  • Zelda Jul 06, 2008

    Was not the problem. Suspect faulty rotor sensor.

  • Anonymous Mar 14, 2014

    when I brake I hear a tuck sound in the front. A friend looked at the brake pad etc and said that they are fine?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 426 Answers

Sounds like a loose retaining pin

Posted on Jul 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Good Morning. How do I change front brake disc of a Toyota Quantum 2.5 d4d please. thank you.


the fsm covers this
alldata.com coves this
and 1000s for youtube and google searched links tool.

are you asking how to do brake service, with no training?
read a book on brakes, here are 100s at the library, or at barnes and noble.
part of brake service is not just swapping pads
its inspections, and fluid purging, (maintenance to make it last longer and not fail, and cause and accident)
why not just get it service, or take an ASE class on brakes 10x better..

Dec 23, 2014 | Toyota Cars & Trucks

1 Answer

Change brake pads


For starters the front and rear us disk pads and it is not hard to do. On the front jack up the front and us jack stand for safety. After you take of the wheel remove the two bolts at the back of the brake caliper remove the caliper and then the old pads us a C- clamp with one of the old pads installed in the caliper then just us the c-clamp to push the cylinder all the way in until it will go no further install new pads put back on. But before you do the next side hit the brake to push the cylinder back out. Go to other side do the same thing. On a side not you only need to replace the rear brakes every other time you do the front. The front wear twice as fast as they do most of the stopping.

May 19, 2013 | 2004 Buick Century

1 Answer

1993 buick lesabre changed the front rotars and pads and now the cars brake pedal is so hard to push down to get car to stop. Mechanic has checked both the front and back brakes and they are fine. T


I would jack up a front wheel and see if pushing on the pedal with the engine running will stop the wheel from turning.
You need to know if the pressure is reaching the wheels, or if the pads and rotors are too slick to stop the car.
Usually if the pedal is hard, the booster is not working or the brakes are glazed.
Can you stop the car with the parking brake ? That only uses the rear brakes.
You may need a second opinion from a different shop.

Jul 19, 2012 | Buick LeSabre Cars & Trucks

1 Answer

1989 toyota pickup front disk brake pads replaced, now the front calipers wont clear the new disk brake pads! Any solutions, please?


remove caliper, push disc all way home, put wheel nut on to hold home, retry fitting them the disc may be slightly scued. If no go try diffrent brand of pad I had same prob with a diffrent car last week & diffrent brand pad was 2mm thiner. If can't exchange pads get piece of emery paper on flat surface & sand away top part of pad material in round motions both ways till they fit. :-)

Jul 09, 2012 | Toyota Cars & Trucks

1 Answer

Remving caliper pins on 2000 vw jetta and caliper


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Jun 26, 2011 | 2000 Volkswagen Jetta TDI

3 Answers

How brakes work


the brakes slows the movement of the car then the trans and engine slows with that I guess you know you have brakes on all 4 wheels by braking you are slowing down the wheels

Apr 16, 2010 | 1999 Dodge Intrepid

1 Answer

Do i need special tool to change the front break pad?


I'm going to assume you are talking about the front brakes since the brake pad warning light is wired to the front drivers side brake pad. Is this is the case you shouldn't put off changing the brake pads and rotors too long after the warning light comes on because you don't want to damage the caliper and cost yourself more money. Do them atleast within the next 500 miles if not earlier. The front brakes on the Jetta are standard single piston disc brakes. Buy decent new brake pads and you might as well buy new rotors instead of getting the old ones turned down (resurfaced, makes them thinner). You should also buy new brake fluid (good stuff) and flush the lines since VW recommends changing it every two years and it keeps the brake system clean and free of corrosion (saves money in the long term). Then you just jack up the vehicle, pop off the tire, loosen the caliper bolts, pull off the caliper making sure to still support it so the brake line doesn't get damaged (rig something up to hang it off the spring on the strut, i.e. bent metal clothes hanger), remove the one screw that holds on the rotor, pull off the old rotor, and remove old pads. There will be a pad sensor wire on the left front that you need to take off too. At this point you might need to push in the caliper piston in order to get the new pads seated correctly. There is no trick on the front calipers like the rear ones (the rear ones need you to turn the piston while pushing it in and is easiest to do with a special tool). You can use and old c-clamp or borrow a caliper tool fron a local auto parts store for the front. You should mount the new rotor first, then you might want to open the brake fluid reservoir (in the engine bay at the back, i.e. closest to cabin, in front of the driver), push the caliper piston back in, mount the new pads by usually sliding them on (use some brake quiet on the back if they don't have anything on them already), and put the caliper back on. The new pads might have the attachment for the sensor. You need to find out all the tightening values for all the bolts you remove and the best way for this is to buy the Bentley factory repair manual for your car (about $80). This will have the procedure I just outlined. It will also tell you how to change the brake fluid. The website forums.tdiclub.com will also have lots of answers for you and probably has pictures on how to do the work. I also recommend worldimpex.com or germanautoparts.com to buy whatever parts you need.

One thing I should mention, the rear brakes in these cars wear out long before the front brakes. If you have never had those serviced you should really look at them too. They may be down to metal on metal if the fronts are worn out.

Sep 09, 2008 | 2003 Volkswagen Jetta TDI

3 Answers

Brake pedal goes too far down. Brakes still stop car fine. Too much pedal travel. 2005 model year.


You have to check your master cylinder, pump your brake several times and hold it, see if is going down to the bottom, if does, the master cylinder is wrong, check the brake pressure hose, maybe you have some air in your brake lines, be sure you have enough brake fluid

Jul 27, 2008 | 2004 Toyota Camry

1 Answer

HONDA ACCORD BRAKED


What type of pads are you guys using? The number one complaint on cars is brake noise. One of the best solutions is to use quality ceramic pads. You may have cailpers sticking. If you have scorch marks on rotors or pulsation in pedal after resurfacing rotors, this is a good indication.

Jul 05, 2008 | 2000 Honda Accord

4 Answers

2002 Jetta Brakes


On one of the front driver side pads there is a sensor for low pads. He either did not hook it back up or got a lose connection to it.

May 29, 2008 | 2002 Volkswagen Jetta TDI

Not finding what you are looking for?
2001 Volkswagen Jetta TDI Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...