An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert who has answered 200 questions.
An expert whose answer got voted for 20 times.
Re: remote central locking
I had the same problem with my Focus. There is a fuse on the back of the fuse block under the dash. There are a couple of bolts holding this block in place. Take these bolts out and find the fuse on the back. Mine was blown. Good luck. Also the sensor unit is behind the glove box. With a little prying of the tabs, the glove box will tip down.
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Look on the back of the fuse board ,for this you have to drop the fuse board as their are two fuses at the back and i know one is for the central locking ,the other ? Now when the hazard switch is disconnected the indicators shouldnt work but the only thing i can think of is the indicator unit is faulty ,do the hazards light the indicator lights up and they dont flash or is nothing happening?
Obtain all keys fitted with remote control. Fasten seat belts and close all doors. Turn ignition switch from position I to position II 4 times within 6 seconds. Switch ignition OFF. Programming mode activated for 10 seconds proceed as follows: Press and hold lock, unlock or boot release button Fig. 1 ,  or . Wait for acoustic signal (indicates correct programming). Repeat above procedure within 10 seconds to program remaining keys. To exit programming mode: Turn ignition switch to position III or wait 10 seconds. Keys can also be programmed using diagnostic equipment. NOTE: A maximum of 4 keys can be programmed.
try putting the key in the ignition and turning it to on then holding the unlock button for 30 seconds and then remove the key and try the remote if still no good go to your dealer and get them to reinishalise the system
I have a clio II, 2001, i have the same problem and i fixed it.
Don't know if will work for you but here it goes:
1 - no key in ingnition
2 - press the unlock button in console off the car for about 10 seconds(dont let go)
3 - it should work the central doors one time and then 2 times( hear)
4 - press the remote a few times until it starts working
It worked for me hope the same for you.
Please tell me if it worked and pass the message.
Hi I wonder if you can advise me ,my central locking and alarm is very unreliable it keeps making a beep before the ignition goes on and clicking,it sometimes sets the alarm off,Ive had the AA round and theyve told me the car battery is dead,which I appreciate,but think the key hub central locking or alarm is running the battery low does the hand held button need a new battery,or can I take the fuse out for the central locking,dont want to pay 66 quid for a new battery if I can pay 2 quid for a new battery for the central locking button,or demobilize it
is central locking not working with remote & did you try using key to see if central locking is working at all if working with then its a good chance that key fob is faulty if its not then first need to check fuses & for radio is it going on when switched on display will say code---- if it does then it req code if not then again possibilty a fuse might be on same circuit as your central locking fuse
if your talking about locking with the remotes.try reprogramming them.cycle the ignition key from run to off 8 time within 10 seconds ending in the run position.the horn should honk.now you are in programing mode.hit the lock button on the first remote then hit the lock button on the second remote.and tunr the key off