Question about 1997 Chevrolet Lumina

1 Answer

Cruise control just stopped working

I cannot get the cruise control to engage. I checked fuses that might be related and they are fine. How do I troubleshoot this?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 330 Answers

Are you use cruise control a lot?

Posted on Jul 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2005 Silverado brake lights on tail not working, cruise out , bulbs and fuses ok


Brake light switch? The cruise and brake lights problems are likely related. The cruise control cuts out when you press on the brakes. I had a van where the cruse wouldn't engage. Then someone pointed out my brake lights were always on. It was the switch.

Dec 03, 2016 | Cars & Trucks

1 Answer

Cruise control not working


cruise controls are dependent on the following sensors all working together
brake sensor
clutch sensor
auto--vehicle speed sensor
rpm's sensor
fuse for the cruise control
cruise control switch either or all not working will stop the cruise control from engaging
road speed at which you can engage the cruise control has to be above a reset speed before it will cut in and work

Sep 05, 2015 | 2009 Chevrolet Chevrolet Equinox LS

1 Answer

Town and country 2000 lxi cruise control won't engage


The cruise control needs a working speed sensor to determine when to engage. You also might have a blown fuse in a related circuit.

Oct 10, 2014 | Cars & Trucks

1 Answer

1997 mazda 626 cruise control not working


Check the 20A STOP FUSE and 10A METER FUSE in the joint box but also there may be no speed sensor input that signals the cruise control to engage.

Sep 09, 2014 | 1997 Mazda 626

1 Answer

Cruise control not working


several places to start looking check connections at cruise module under hood check vac connections make sure your brake light switch is functioning properly use a test light to check for a signal at the brake lite switch by engaging and disengaging the brake pedal check connections by the multi function switch block on the rt side of the steering column check for a signal be again engaging and disengaging the cruise control control switch or if you have access to a tech2 these test can be made thru it check all fuses related to system

Sep 04, 2012 | 1993 Chevrolet Suburban

2 Answers

How to fix cruise control


Cruise controls can cease to engage if the clutch or brake light cruise switch are out of adjustment. If this happens, try placing you foot under the clutch pedal (if equipped) and lift up on it (toward you) and hold it while engaging the cruise. If it now works, it will likely cut out when you remove your foot from under the pedal. Check the brake pedal in an identical fashion. Adjusting the switch at the pedals can often solve he problem. Some vehicles (Honda, Acura, Ford, to name a few) have a plastic insert that mounts in the pedal arm which presses against the switch. These can become brittle and fracture into pieces. My Acura has little pieces of blue plastic on the floorboard around the brake pedal one afternoon and I noticed the cruise didn't work. It was the pieces of the insert that had come to pieces preventing the cruise from coming on. I replaced the insert and no more problem with the cruise.

Mar 10, 2012 | 2003 GMC Sierra 2500HD

2 Answers

I own a 2005 GMC Canyon Five CYL and the cruise control stopped working last niight. You push the button and no cruise. I checked the fuse and it is ok I exchanged with another 10AMP and no change still...


Start with the simple and check the fuses and the Stop lamp switch. Check your brake lights, if they're not working, the cruise won't work either. If they're not working, check the fuse for them, if the fuse is fine, then take it into the dealer, there's been a recall issued on the brake switch, so it should get fixed for free.
Cruise Control Disengaged
The powertrain control module (PCM) disengages the cruise control operation based on the signals from the following switches:

* The stop lamp switch
* The TCC brake/cruise release switch
* The clutch release switch, if equipped
* The cruise control On/Off switch

The TCC brake/cruise release switch and the stop lamp switch are mounted on the brake pedal bracket. When the brake pedal is applied, the normally closed TCC brake/cruise release switch opens and the normally open stop lamp switch closes. The PCM detects a low signal voltage on the TCC brake/cruise release switch signal circuit and a high signal voltage on the stop lamp switch signal circuit. When the clutch pedal is applied, the normally closed clutch release switch opens and the PCM detects zero voltage on the CCP switch signal circuit. The vehicle speed stored in the memory of the PCM will be erased when the cruise control On/Off button is turned OFF, or the ignition switch is turned OFF.

The Cruise Control System will disengage when the PCM detects that a driver override function has been active for approximately 60 seconds .

When the Cruise Control System is disengaged, the PCM sends a class 2 message to the instrument panel cluster (IPC) in order to deactivate the cruise control indicator.

Cruise Control Inhibited
The powertrain control module (PCM) inhibits the cruise control operation when any of the following conditions exist:

* A cruise control related DTC has been set.
* The vehicle speed is less than 40.2 km/h (25 mph) .
* The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear.
* The engine RPM is too low.
* The engine RPM is too high, with fuel cut off.
* The vehicle speed is too high, with fuel cut off.
* The system voltage is not between 9 volts and 16 volts .
* The Traction Control System (TCS) is active for more than 2 seconds .

Thank you for using Fixya and start with replacing the stop lamp switch. Even though the brake light work, it;s been known for that switch to cause your issue. that's way there was a recall for it.

Apr 01, 2010 | 2005 GMC Canyon

2 Answers

2005 chevy tahoe cruise control not working, no blown fuses


The BRAIN BOX which is known by most car owners controls the throttle boy accellerations control when engaging the cruise control on. If your fuses are good I recomend have the servo (brain box) checked

Jan 23, 2010 | 2005 Chevrolet Tahoe

2 Answers

Cruise control problem


There are 3 places on the Rav4 where fuses can be located and checked. for the cuise control.

The back of the cruise control stacking switch has been know to fail (fall apart) and Toyota issued a TSB with replacement switch.

if it is the fuses then they most likely are related to cruise control system: Stop, Dome, Gauge and Igniton
The interior fuse box
The main engine fuse box (by brake fluid)
Cruise control ECU is under the glovebox.
Cruise control actuator is under hood (by driver side brake fluid/booster)Throttle position sensor (to detect if your foot is on gas pedal)
Cruise control switch on the clutch pedal too (if you have 5spd manual)
Brake lights are the deactivate signal for the cruise control


Aug 13, 2009 | 1998 Toyota RAV4

2 Answers

I have a 2001 Focus station wagon. the cruise control will not engage. And the high beams will not stay on (I can flick them, but they won't stay). Are these loose switches of some sort, that I could...


I would check the easy things first. That is the brake switch and the clutch switch (manual trans). Drive down the road and pull the brake pedal up with your foot and then try to set the cruise (same with the clutch pedal). Also the cruise requires that the brake light bulbs be in working order (and that there are no LED brake lights). Check fuse numbers 53 54 and 59.
The high beam problem might be related to the cruise issue, but I can't think of a reason why.

Jul 29, 2008 | 2000 Ford Focus

Not finding what you are looking for?
1997 Chevrolet Lumina Logo

Related Topics:

615 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

66302 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...