Question about 1995 Ford Contour

1 Answer

Cars- Please could help me with the torque setting for Ford 3.4, V6

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 55 Answers

Please specify what torque you need. The head bolt torgue? The lugnut torque? The motor mount torque. Every bolt has a required torque. Mr. Rodney Long

Posted on Jul 02, 2008

6 Suggested Answers

  • 14036 Answers

SOURCE: 1999 ford focus rear wheel

WHEEL BEARING LARGE HUB NUT TORQUE 232 FT LBS.

Posted on Mar 13, 2011

Testimonial: "thanks for your help"

ewashmidas
  • 362 Answers

SOURCE: 2000 W reg ford escort wheel nut torque settings

2.0L DOHC Engine 85-105 Ft Lbs EX 2.0L DOHC Engine 65-87 Ft Lbs

Please let me know if this information is helpful. Positive feedback is appreciated. Thank You!

Posted on Mar 28, 2009

chuck943
  • 783 Answers

SOURCE: torque setting

173 ft lb

Posted on Mar 19, 2009

  • 111 Answers

SOURCE: need bigend torque settings for a Ford Ranger 3.4

need more info as to what your working on heads block etc

Posted on Sep 13, 2009

kennyz195
  • 61 Answers

SOURCE: ford 1.8 diesel engine water pump torque settings

17- 20 lb-ft torque would be fine.

Posted on Apr 07, 2010

  • 1 Answer

SOURCE: Sets TC 37 torque management fail fault code.

i got same problem with this ..anybody settled??

Posted on Dec 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Upper ball joint torque specs 2002 explorer xls 4x4 4.0L v6 gas


Douglas, 90 lb-ft is ball joint nut torque.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Install Upper Control Arm and Ball Joint 2002 05 Ford Explorer...

Apr 02, 2016 | 2002 Ford Explorer

1 Answer

I'll pan torque spec on 2002 rord ranger 4.0 sohc


SOHC V6 Torque Specifications - Ford Explorer and Ranger Forums ...

https://www.explorerforum.com/forums/showthread.php?t=406687
Apr 25, 2014 - SOHC V6 Torque Specifications Under the Hood. ... related to the Ford SOHC V6 4.0L engine used in Explorers, Mountaineers, Mustangs and Rangers. .... Oilpan (sheet metal) to crankcase reinforcement section bolts: 80 lb-in (E/MWM) ....Ranger Mountaineer - Sport thru '03 - 2nd Generation, 2002 - 2005 ... Transmission pan drop
5 posts
May 7, 2012
SOHC V6 Timing Chain Inspection & Repair
19 posts
Aug 10, 2010
Another transmission won't go after fluid change
19 posts
Mar 14, 2009
Help with 4.0 SOHC timing
15 posts
Mar 12, 2006
More results from www.explorerforum.com

[PDF]SPECIFICATIONS > TORQUE SPECIFICATIONS

www.askatech.com/askatechlive/forums/resourcehandler.ashx?a=5581
Jan 6, 2014 - TORQUE SPECIFICATIONS ... ENGINE - 4.0L SOHC. 2002 FordExplorer Sport Trac 4.0L Eng. (1). (2) ... Oil Pan Ladder Frame Bolts (Inside).

Torque Specifications - AutoZone


Jan 04, 2016 | Cars & Trucks

1 Answer

Looking for torque setting for 2002 ford ranger with a 3l rocker arms


The bolt torque spec for the 3.0 Vulcan V6 rocker arms is 18-26 foot lbs, I always set it in the middle, so 22 foot lbs will do just fine. If I helped please rate me for fixya.com
Thanks

Oct 25, 2011 | 2002 Ford Ranger Regular Cab

1 Answer

What are the torque specs. for the harmonic balancer on a 2004 ford explorer with the 4.0 V6


Hello qsswanson33: My name is Roger and I will help with your answer. Tighten the bolt to 33 ft.lbs. then tighten an additional 85 degreese. This will acheive the propper torque. Should you need further help please just ask. Please rate the answer. Thank you for using Fix Ya. Roger

Aug 01, 2011 | Ford Explorer Cars & Trucks

1 Answer

Head bolts torque settings for 1993 ford taurus 3.0 engine


These are the torque valies and sequences for your engine
Torque in 2 steps [1st (33-41 ft-lbs),
2nd (63-73 ft-lbs)]


Torque sequence: (for each bank)
------------
6 4 2 8

5 1 3 7
------------

Good luck and please rate this solutuon

May 21, 2011 | Ford Taurus Cars & Trucks

1 Answer

What do u torque head bolts at for 98 ford ranger 3.0 v6


Its a four step procedure.1. 59ft,lbs. 2.loosen one full turn. 3. 31-41ft lbs. 4. 63-73ft lbs. these are torque to yield bolts and must be new!

Mar 27, 2011 | 1998 Ford Ranger SuperCab

1 Answer

1998 FORD FESTIVA HEAD BOLT TORQUE SETTINGS & TIGHTENING SEQUENCE (1.5 LITRE ENGINE)


1978 - 1980 FORD FESTIVA 1.6L 65-70 Foot pounds (Final torque)
Torque sequence 9 3 1 5 7 8 6 2 4 10 Step 1: torque to 5 Ft/Lbs Step 2: torque to 20-30 Ft/Lbs Step 3: torque to 50-55 Ft/Lbs Step 4: torque to 65-70 Ft/Lbs Recheck final torque in sequence


1988 - 1993 F0RD FESTIVA 1.3L
Torque sequence front of engine 8 4 1 5 9 7 3 2 6 10 Step 1: torque to 35-40 Ft/Lbs Step 2: torque to 56-60 Ft/Lbs Recheck final torque in sequence

2011 FORD FESTIVA 1.6L NO TORQUE SPECS AVAILABLE THERE IS NO FORD FESTIVA MANUFACTURED IN 1998 ALSO NO FORD FESTIVA MANUFACTURED WITH A 1.5L ENGINE
HOPE THIS HELPS YOU

Aug 06, 2010 | Ford Focus Cars & Trucks

1 Answer

I need head bolt torque specs. for a 2002 ford f150 v6


Torque Specifications for Ford 4.2L-256ci-V6
These bolts are torque and turn procedure!
STEP 1: 14 FtLbs STEP 2: 29 FtLbs STEP 3: 36 FtLbs STEP 4: LONG Bolts Loosen 3 Turns - re-torque to 33FtLbs STEP 4: SHORT Bolts Loosen 3 Turns - re-torque to 19FtLbs STEP 5: ALL Bolts +180deg turn

Aug 05, 2010 | 2002 Ford F150 Regular Cab

3 Answers

I need torque settings for the engine ie head bolts v6 engine 1


i am replacing the heads on a GMC 350 cu in engine. what is the final torque of the head bolts?

Jul 15, 2010 | 1985 Chevrolet Camaro

1 Answer

1986 Mustang 3.8L cyl. head torque.


The aluminum heads on a cast iron block require some gentle torque procedures.... It may not be necessary - but I suggest that you start near the center of the head and work out with each tightening step. This will ensure that you don't put too much pressure on a single portion of the head. The standard proceedure for the 3.8 V6 up until 1994 is as follows:
You will have some long and some shorter head bolts. Place a small mark on the long bolts to identify them during the final torque proceedure.

Step 1: 15 (on all bolts)
Step 2: 29 (on all bolts)
Step 3: 37 (on all bolts)
Step 4: Now, starting near the center of the head, loosen a single head bolt about 2 turns. Now, torque it down to about 15 (+/- 3 lbs) IF A LONG BOLT.
OR 11 (+/- 3 lbs) IF A SHORT BOLT.
Step 5:
After all bolts are set as described above, ....go over them 1 more time, starting near the center of the head and pull each bolt down another 1/4 turn (90 degrees).
You are done!!

Oct 10, 2009 | 1986 Ford Mustang

Not finding what you are looking for?
1995 Ford Contour Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...