Question about 2000 Chrysler Grand Voyager

1 Answer

Air filter change

How do you remove the housing on the air filter?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 85 Answers

Loosen the clamp at the throttle plate, remove two 10mm bolts from intake resionator, rewove pcv fresh air tube, loosen clamp on resionator to filter housing, remove 10mm bolt at top of filter housing, remove filter housing, open housing remove filter install new filter and reverse process.

Posted on Jul 02, 2008

3 Suggested Answers

c17hydro
  • 2984 Answers

SOURCE: how to remove air filter housing to replace

Looking at the directions....for battery removal, it doesn't state removing the air filter cover but to do that, all you do is unclip the cover of the air cleaner....very simple.

Posted on Mar 28, 2009

  • 2 Answers

SOURCE: change engine air filter

Those are the only 2 bolts

Posted on Apr 28, 2009

Suraido
  • 195 Answers

SOURCE: cabin air filters

There are 2 seperate filters in the car, one that clean the air the engine is fed, and one that cleans the air that comes into the the cabin. The one for the cabin is usually hidden somewhere behind the glove box. The surefire way to find it usually is to find the blower assembly for the heater and fan and all that is also usually located behind the glove box, if you find that then the filter is either inside the whole assembly or you have a slot or port or whatever on the ducts near the blower that contains the pollen filter for the cabin.

Posted on Jul 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air filter


Remove the 2 screws (10mm) on top that hold the air intake housing, Pull the air intake away from the air filter housing. You may need to loosen tubing with flathead screwdriver. It's easier to replace the filter if you remove the filter compartment so remove the screw that holds this piece in place. Pull the air filter housing out gently. You may have to work it out since space is compact. Pop the clips, replace the air filter and reverse to re-install.

Read more: http://wiki.answers.com/Q/How_do_you_replace_the_air_filter_in_a_2000_Chrysler_town_and_country#ixzz25R4Kd5Ya

Sep 03, 2012 | 1996 Chrysler Town & Country

1 Answer

How do I get the plastic case off so I can change the air filter on my 2000 grand voyager?


Hello jasonandc863,

1. remove the two screws and air inlet resonator see figure below.

netvan_162.png

2. Loosen 3 clamps holding air cleaner housing half together.

3. Remove left half of air cleaner housing.

netvan_163.png

4. Remove filter element from air cleaner housing.

netvan_164.png

Reverse order to install.

I hope this helps.

Regards,

netvan

Aug 15, 2011 | 2000 Chrysler Grand Voyager

1 Answer

How to change air filter on a 2009 hyundai sonata


Hi there, here are a few steps to help you out:
  • Turn the Sonata off to eliminate the risk of engine backfires while changing the air filter. Leave the car off until the filter has been replaced or there is risk of injury.
  • Lift the hood of the Sonata. Locate the air filter housing unit on the passenger side of the car, in the front corner. Look for a black, plastic cylinder that has an accordion-type hose attached to it that leads to the engine.
  • Remove the air intake hose and air duct from the housing unit. Disconnect the connector for the air-flow sensor from the filter cover. Unclip the clip on the filter cover. Lift the cover off the housing unit.
  • Take out the old filter from the housing unit. Remove any remaining debris out of the air filter unit. Wipe the inner and outer surfaces of the housing unit with a damp cloth.
  • Place the new air filter in the housing unit. Use a K&N air filter, part number 33-2346.
  • Replace the cover on the housing unit and clip it in place. Reattach the air-flow sensor. Put the air intake hose and air duct back in place on the housing unit.
Best of luck....

Jan 13, 2011 | 2009 Hyundai Sonata

2 Answers

How do you change the engine air filter in a 2008 toyota sienna


REMOVE ENGINE COVER DISCONNECT MASS AIR FLOW SENSOR CONNECTOR.LOOSEN AIRDUCT FLOW TUBE SCREWS THEN REMOVE AIR FILTER COVER HOUSING BOLTS THEN RAISE AIR FILTER COVER UP SLIGHTLY ENOUGH SLIDE IT AWAY FROM AIRFLOW DUCT.THEN REMOVE COVER REPLACE AIR FILTER THEN PUT EVERYTHING BACK UP VISA VERSA DONT FORGET TO TIGHTEN SCREWS TO AIRFLOW DUCT TUBE ONCE AIR FILTER HOUSING BACK IN PLACE.

Aug 31, 2010 | 2008 Toyota Sienna

1 Answer

How to change air filter on a 2002 jetta tdi


Air filter changement for 2002 VW Jetta 1.9 TDI:
1. Unplug MAF Connector.
2. Unscrew two Air Filter Housing screws - Phillips driver.
3. Screws do not come out fully. They remain loose in the Housing.
4. Remove Air Filter Housing. Lift up/towards. Rest on battery cover.
5. Remove old Air Filter.
6. Clean Filter Housing. Damp cloth.
7. Check upper half of cover too.
8. Insert new Air Filter. Ensure the edges are seated.
9. Reposition Filter Housing. Clips on leading edge down/in first.
10. Two screws (don't overtighten).
11. Reconnect MAF plug.


ad58f60.jpg

Aug 30, 2010 | 2002 Volkswagen Jetta TDI

1 Answer

How to change air filter for toyota camry 2003 thanks


The steps are described below

  1. Turn off the car before changing the air filter. Don't start the car once the air filter has been removed, it acts as a barrier were the car to backfire.
  2. Locate the box that houses the air filter. Look in the front driver's side of the car, closest to the windshield, near the center of the engine compartment.
  3. Undo the clips that keep the housing lid secure. Lift the lid and compress the accordion-type tubing towards the engine.
  4. Remove the old filter from the housing unit. Clean any leaves or debris out of the box.
  5. Replace the old filter with a new filter that is made for the specific make and model year of your Toyota Camry. Use a K&N air filter, part number 33-2260, for a Camry manufactured from 2002 to 2007.
  6. Pull the lid back over to the air filter housing unit, and snap it in place. Reattach the clips to secure the lid.

Mar 10, 2010 | 2003 Toyota Camry

1 Answer

How to change air filters on 2007 Mercedes C230 Sport


I have '05, both should be similar:
1.Cabin air filter is located above battery on right side against firewall.
Release three latches, remove filter housing, slide old filter out (housing is flexible), insert new
one, reinstall housing.
2.Engine air filter is on the left side of the block (follow intake hose). Cover is retained with six screws
(six point star shape,I belive called Torox, bit/scredriver size 25). Loosen screws (don' t pull all the
way out of the cover) lift cover , and remove old filter. Insert new one, reinstall cover. DO NOT
OVERTORQUE SCREWS! Screw holes in plastic filter housing strip very easily.
Note: Intake hose is very flimsy, one on my car came apart and had to be replaced.

Mar 25, 2009 | 2007 Mercedes-Benz C230 Sedan

2 Answers

I have 2006 Acura TL V6. How do I change the cabin air filter?


To change cabin air filter on Acura TL firs time you need to open the glove box and then remove the arm that holds the glovebox. Press the 2 sides of the glovebox to take this out like in picture bellow.
acura-tl-2004-2010-cabin-air-filter-location.jpgAcura TL 2004-2010 cabin air filter location
After do this you can see and locate the cabin air filter housing cover.
acura-tl-2004-2010-cabin-air-filter-housing-cover.jpgAcura TL 2004-2010 cabin air filter housing cover
Push the 2 tabs from the filter frame to unhooking from the housing cover. Take the frame out and replace the old cabin air filter with the new one with the air flow indicating arrow pointing down.

acura-tl-2004-2010-reinstal-the-air-cabin-filter.jpgAcura TL 2004-2010 reinstal the air cabin filter

Nov 26, 2008 | 2006 Honda Accord

1 Answer

How to change an air filter in 99 Intrigue 3.8


  1. Disconnect the IAT sensor electrical connector.
  2. Loosen the air inlet hose clamp.
    444460.gif
    tif.gif
  3. Carefully remove the air inlet hose from the throttle body and air cleaner cover (5).
  4. Remove the 2 housing cover retaining Screws .
  5. Remove the air cleaner cover and carefully remove the air filter element.
  6. Inspect the housing cover (4), seal assembly, and air ducting (2) for damage. If a problem is found, replace as necessary.

Nov 26, 2008 | 2000 Oldsmobile Intrigue

1 Answer

Internal Air Filter


Remove the air intake tubes on the left and right sides. Pull the complete air filter housing up off the rubber mounts. Turn the air filter house upside down and there will be 4 T20 torx head screws on both sides. Unscrew them and remove. Install new air filters and put housing back on in reverse order.

Jun 29, 2008 | 2005 Subaru Outback

Not finding what you are looking for?
2000 Chrysler Grand Voyager Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...