How do I adjust the high beam. They are pointing up

low beam and high beam is in the one setting unless you have separate headlights
procedure is to place the car on level ground 3 feet from a wall that reflects the head light
draw a cross on the wall at the height of the center of head light lens
switch on the head lights (high beam)and you will see the center beam of high beam on the wall
using the screws at the back of the assembly adjust that spot to be pointing slightly to the left if rh drive ot left if lh drive and about 1 inch below the line that you drew on the wall
when you have that correct , it will put the low beam in the correct legal position
if the rear of the vehicle is sitting down , trailer of caravan on , the the head lights have to still be adjusted to legal setting

from the front or back of the head light , there will be 2/3 adjusting knobs / screws . Place the vehicle on a level surface about 3 feet from a plain coloured wall. You will see the centre of the beam( High beam). The centre of the beam is to be at the same height as the centre of the head light lense and properly adjusted pointing slightly to the passenger side of the vehicle . This prevents full beam in the eyes of oncoming cars.

I have a similar problem. The adjustment screw adjusts both the high and lof beams. After changing the passenger side low beam, both sides then pointed at the ground. High beams were fine. I adjusted so the low beams are fine but now the high beams point straight up.

In talking with Subaru Service he said there is a "module". He said after changing the bulbs they should point down then auto-adjust back up. That didn't happen. I haven't found anything on such a module. He said it woul be $109 for adjusting the lights OR for the module.

If I find anything more I'll let you know.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Yes you can. There is an adjustment screw at the top of each head lamp and you just turn them out or counter clockwise and the beam will come down. You may also have to adjust them side to side also. There is an adjustment screw as well.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.