Question about 1998 GMC Sierra

2 Answers

1998 gmc3/4 ton truck

Just replaced the motor in the truck and it will not start. what could be the problem.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check the distributor and make sure it isn't 180 degrees out

Posted on Dec 14, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 330 Answers


1. Replace the engine, new one or used one. Do you know the engine is OK?

2. It is hard to tell you what’s happening, please if you can give me more information, maybe I can give you what I thought.

Posted on Jul 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 5.7 vortec installed in 1984 1 ton will start but not run. Fuel pressure is 50 psi. Wiring is installed on motor but from computer to steering column not so much.


You would need to have everything hooked up like it was in the 1998 engine . All computer powers and grounds and all signals from engine to pcm.

May 31, 2015 | Cars & Trucks

1 Answer

98 cadillac seville windshield wipers run at randm


thats tricky it could be the switch or motor or it could be the ground negative for the motor try running a wire from mount bolt off of wiprt moter and grounding it to another bolt on frame or fire wall or negative to battery just ton eliminate the prob. of it being a simple ground before u replacce switch or motor

Sep 06, 2012 | 1998 Cadillac Seville

1 Answer

I have 1998 gmc 3/4 ton auto . a.b.s light comes on intermitantly. when it does I also loose my full heater controls and cruise control. new brake switch has been instaled but c'ant see how that would


It is coincidence that your heater control went at the same time your ABS control went out. Try replacing the ABS control and see if that fixes it. Many times because of the electrical complexity you have to just start replacing things until you get it unless you own one very expensive computer.
Look for loose wires. Also try it in reverse if you like. Replace the heater control and see if that fixes it all. Also check ALL fuses.

Dec 06, 2011 | 1998 GMC Sierra

1 Answer

Have 1998 1 ton ford van lost keys ,how do you


why dont you take the vin number to dealer they will make the key for you if only it is original ignition cylinder

Mar 27, 2010 | 1997 Ford F350 Crew Cab

1 Answer

What is firing order in dodge ram 1500 hemi


1998 Dodge RAM 1500 ½-Ton 4WD Pickup 5.9 liter V-8 VIN "Z"

1fa0727.gif



1998 Dodge RAM 1500 ½-Ton 4WD Pickup 5.2 liter V-8 VIN "Y"

22bfd79.gif

Hope this helped.

Mar 22, 2010 | 1998 Dodge Ram 1500 4WD

2 Answers

Where do i find the O2 sensor on a 1998 ford f-150 4.6lt truck


1998 Ford Truck F150 1/2 ton P/U 4WD 5.4L EFI 8cyl
The Oxygen Sensor is located under vehicle, passenger side, below seating area, rear of catalytic converter, mounted in exhaust pipe.

Application: Number three

Hope helps (rated this) Good luck.


Jan 12, 2010 | Ford F-150 Cars & Trucks

2 Answers

1998 gmc 4.3 starts up but loses power 3-5 mins later,will restart and run again for another short time,fuel filter has just been replaced.


Install a pressure gauge, start and run 3-5 minutes and watch the pressure. You should see the pressure maintain as it did when first started. If it begins to drop, the fuel pump has gotten weak and is starting to fail.
Let me know what you find.
Regards.

Mar 05, 2009 | 1998 GMC Sierra

2 Answers

Blowermotor for heat stops running


i would say its the blower motor resister thats bad. had same problem. put new one in fix it. its located behind the glovebox on top of the heater box. be forwarned its a bear to change because there is not much room.

Dec 27, 2008 | 1999 Chevrolet Silverado 1500

1 Answer

Power Windows


Improper installation could have caused the replacements to fail if the limit switches that prevent the motor from operating when totally closed or opened may not be adjusted right. Once the pane is run against the ends of its travel, the motor could draw a ton of power which would cause it to heat very quickly. Those motors are made as cheaply as possible and probably are not designed as larger ones that are now almost all thermally protected.   

Jul 17, 2008 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
1998 GMC Sierra Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21987 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...