Question about 1995 Pontiac Sunfire

1 Answer

E ngine im trying to put a 95 sunfire back together,but there is a hole next to the therostat and cant figure out what goes there.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Heeter hose?

Posted on Sep 25, 2008


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 95 gmc sierra 2500 and im trying to put in my aftermarket rafio so i cut the stock harness out the square puece that goes in back of stock radio and now i cant figure out what wire is what i got...


I would suggest you spice the wires back to stock harness by male and female connections and tape over them with black tape then get a stereo install kit that includes a wiring harness ( cost about $20 maybe or less) for the year of truck you have... it will plug right to your stock harness ...never just cut stock stereo wires from stock plug it will be more of a headache than you think trust me I've installed all my own stereo system been there done that... good luck

Mar 31, 2015 | 1995 GMC Sierra

1 Answer

Which hose goes where on my 2000 pontiac sunfire heater core...


are you installing the correct thermostat the right in the head or block
3 thermostats indicate incorrect fitment method
heater hoses run either way as the water is pushed through the heater core by the pump

Apr 21, 2017 | Cars & Trucks

1 Answer

We replaced the master cylinder on our 1996 Sunfire. How do we now set the tension on the gears before putting back together.


I am a bit confused here..master cylinder is for brakes..it must be bled out to remove the air bubbles before the actual ines are connected to it..you just cant hook up everything and hope it works...repost with specifics please..

Feb 15, 2013 | 1996 Pontiac Sunfire

1 Answer

How do i change the thermostat in my 96 blazer?


take bracket off throd body then take therostat housen off to change therostat then put back together fill with coolent run with cap off it water goes down then fill on up put cap on drive and watch gage make shur it dont run hot

Jan 31, 2011 | 1996 Chevrolet Blazer

3 Answers

Pontiac sunfire 2.2 1995 no spark from spark plugs


check for power coming from coil packs to wires, could be bad wires, coil packs, ignition module(under coilpacks). check all fuses as well

Oct 06, 2009 | 1996 Pontiac Sunfire

1 Answer

Ngine over fueling at all rpm, rough idle, heavy fuel consumption


if the car is stock i would replace your oxygen sensor. you may also need to clean out the MAF sensor.

May 29, 2009 | 1995 Volkswagen Golf

1 Answer

Backside of engine


There is a special tool you need to purchase . It connects on your front motor mount located on top by radiator.. This is what is called the dog bone in the industry . The specialty tool is put in the place of dog bone mount and is adjustable whith vehicle placed in neutral... The tool pulls the motor towards the radiator giving you complete easy access and complete visibility for what you are trying to achieve

Dec 26, 2008 | 1997 Pontiac Sunfire

1 Answer

The oil dip stick tube was out of the block


will be on driver side rear location you will need to get under car and feel around you will find the hole in that area then you can replace the dipstick housing

Dec 15, 2008 | 1995 Ford Mustang

1 Answer

I have a 95 chevy blazer with the 4.3 vortec. It has a knock sensor and temp sensor on the right side of the engine and I cant remember which one goes in the top hole and which one goes in the bottom hole....


The knock sensor will go to the lower hole, make sure you follow tightening instructions or it will no function correctly. Put a liquid sealant on threads, don't use tape.

Aug 04, 2008 | Chevrolet Blazer Cars & Trucks

Not finding what you are looking for?
1995 Pontiac Sunfire Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...