Question about 2001 Chevrolet Cavalier

1 Answer

Problem removing break caliper

Im trying to remove the break caliper from my 2001 chevy cavalier but i cant get the bolts off

Posted by on

  • Anonymous Mar 26, 2014

    removing front calipers



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 726 Answers

Ok try to put some crc on them and let that soak in 4 a good half an hour then use a breker bar should loosen up a far bit and realese them selves

Posted on Jul 02, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

What size allen needed to remove break pads

Allen wrenches usually come in a set, try 3/8.

Apr 30, 2016 | 2008 Chevrolet Chevrolet Impala LS

2 Answers

98 chevy cavalier has clicking noiise when brakes applied on passenger side

after replacing breaks and rotor did you bleed the breaks?

Dec 03, 2011 | 1998 Chevrolet Cavalier

1 Answer

Lost key to 2001 chevy caviler have took everything off including the steering will but cant get off the ingetion switch what do i do

Without a key you cannot remove the lock alone. You must remove the ignition housing. It is fitted with shear bolts when new, so where the bolts sheared off will look like two spherical dome. Use a small sharp chisel to start unscrewing them the first turn or so, after that, they will only be finger tight.

May 29, 2011 | 2001 Chevrolet Cavalier

2 Answers

Removed two bolts from caliper on chevy venture

Here's a great video that will show you exactly how to remove the rotors from your Chevy Venture.">

Apr 06, 2010 | 2001 Chevrolet Venture

1 Answer

Removing front brake calipers to chage brake pads and rotors

remove the BOTTOM 15mm caliper bolt lift the caliper up and slide off
then remover the 2 15mm bolts holding the caliper housing on
remove the brake rotor (you may have to hit it with a hamer to break it free
depending on the brake pads you got some come with new sliders
remove the sliders clean the rust build up then install new sliders
lube the sliders install the pads
install new rotor
install the caliper housing with the 2 15mm bolts
install the caliper and lube both caliper pins with silicone lube
install wheels

Nov 08, 2009 | 2001 Buick Century

1 Answer

How do you release the anti-lock brake system to replace the rear brake rotors on a 2001 Chevy Impala?

I assume you want to take the caliper off first. Remove caliper bolts & using a pry common screwdriver pry piston on caliper back in a bit or enough to allow the caliper's removal. After this, remove rotor. I hope this helps!

Oct 03, 2009 | 2001 Chevrolet Impala

1 Answer

How to change the brakes on the 2001 chevrolt cavalier

1. Remove the tire.
2. Unbolt and remove the caliper. (bolts are hex, octagon, or torx and are located on the inside part of the caliper.
3. Remove old pad from caliper
4. Compress piston all the way in with C clamp, and then install new pad.
5. Re-install caliper and bolt it back on
6. Replace tire

Oct 02, 2009 | 2001 Chevrolet Cavalier

1 Answer

Cant remove wheel bearing assembly from the spindle 1996 chevy

check the front of the hub assembly, just to double check and see if there is a cap on it with a crown nut behind it. It should not be stuck to the spindle at all and this is the most likely cause. If there is a crown nut there, there will be a cotter pin you have to remove to take the nut off.

Sep 27, 2009 | 1996 Chevrolet Cavalier

1 Answer

I need Help on what to do for changing brake pads

if it is disc brakes all you have to do is remove the two bolts that go through the brake caliper. pull off the brake caliper. remove the brake bads. compress the piston in the caliper so the new pads will fit. then put in your new pads and reassemble.

Apr 06, 2009 | 2001 Chevrolet Cavalier

2 Answers

2001 cavalier front brakes

erare 2 bolts on the backside of the caliper.

Dec 10, 2008 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
2001 Chevrolet Cavalier Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides