The molding in the middle of the door clips on. Remove interior door panel to access the clips, they usually break off. Or do you mean the black tapes (stickers) around the window opening, they are just stickers. Take a heat gun to loosen glue and peel off.
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Remove front door handle bezel screw cover
Remove inside handle bezel screw
Remove inside handle bezel
Lift upward on the rear of the front door inside handle bezel
Disconnect electrical connector
Remove handle screw cover Remove handle screw
Remove door trim panel upper screw
Remove door trim panel lower screw
Remove door trim panel (pull the door trim panel outward to release the pin-type retainers)Remove front door sail panel Disconnect mirror electrical connector
Remove 3 exterior mirror nuts and exterior mirror
To remove the exterior door handle of the 2000 pontiac grand prix, You will be needing these instruments, wrench set, Putty knife, Screwdrivers, Socket wrench set and please follow the steps below:
Roll the door window all the way up. Disconnect the car battery's negative cable with a wrench.
Remove all cover plugs on the interior door panel with a putty knife.
Remove all armrests, door pulls, the window crank and trim-panel
retaining screws with a screwdriver.
Remove and disconnect any electrical devices in the door panel. Pry the controls out with a putty knife, and unplug the wires.
Pry the trim-panel
clips loose with the putty knife. Do not pry on the panel between the
clips, or the panel could be damaged. Separate the trim panel from the
door slightly, and disconnect the courtesy light. Remove the panel from
the door, and peel back the plastic water shield.
Detach the lock rods from the latch. Unhook the rods from the latch holes by hand.
Remove the door-handle nuts with a socket wrench through the service
holes in the door frame. Rotate the lock cylinder as needed for
clearance, and pull the handle from the door.
Usually you have to remove all the handles etc. from the inside. (The screws are covered with plastic plugs or similar.) Then the trimming is held by plastic or metal clips around the edges. Carefully pry the interior off and gain access behind.
remove all inner door trim, and inner window trim, release 2 nylon blocks on top of window scissors and slide window up and out, on outside remove plastic handle trim and undo large nut round doorlock, on edge of door pop out plastic plug and undo coonecting rods, inside door at front of handle is a little cir clip holding a pin through handle, remove both, you should now be able to wriggle handle out to the inside of the car remember to watch for wires to micro switch for cental locking, rebulild is a reveral of this.
SECTION 501-09: Rear View Mirrors
2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION
Removal and Installation
Remove the front door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel —Expedition
Removal and Installation NOTE: Left front door shown, right front similar.
Remove the door handle bezel.
Use service notch.
Remove the window control switch plate.
Use service notch and disconnect the electrical connectors.
CAUTION: To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips. Remove the two bolts and three screws, and remove the door trim panel.
Remove the weather shield.
Disconnect the exterior mirror electrical connector.
Remove the exterior mirror.
Remove the nuts.
To install, reverse the removal procedure.
Install top nut first.
Exterior Mirror Motor
Removal and Installation
Position the mirror glass to obtain a gap at the top edge of the mirror and carefully pull the top edge of the glass away from the mirror housing.
Disconnect the heated mirror electrical connectors.
Remove the exterior mirror motor screws and exterior mirror motor.
first you van order parts at discount from tascafordparts.com.
quest & mecrury villager are the same vehicle made at the same assembly plant. good luck to all. If you were in detroit area, I wold help you.
Trim Panel —Sliding Door
Remove the sliding door trim panel finish panel.
2. Remove the sliding door trim panel
Latch Remote Control —Sliding Door
Remove the rear sliding door trim panel. For additional information, refer to Section 501-05 .
Position the watershield aside.
If equipped, disconnect the sliding door power door lock actuator electrical connector.
NOTE: Mark the position of the sliding door rear latch cable adjusting bracket before removing the bolt.
Disconnect the sliding door rear latch cable.
Remove the bolt.
Remove the sliding door rear latch cable adjusting bracket from the latch remote control.
Disconnect the sliding door rear latch cable from the latch remote control.
Remove the 4 sliding door front latch bolts.
NOTE: If necessary, transfer parts to the new sliding door latch remote control.
Remove the sliding door latch remote control.
Remove the bolts.
Remove the sliding door latch remote control.
Handle —Exterior, Sliding Door
Remove the sliding door latch remote control. For additional information, refer to Latch Remote Control—Sliding Door .
My 96 Camry LE has 9 attachments that are visible. Some have plastic caps covering the screws; others do not. There are screws at the door handle, at the forward portion(with covers) when the door is open and the back edge (small covers). As I recall, there are several friction type fasteners around the perimiter of the panel that can be removed by prying carefully away from the metal portion of the door to free up the trim panel. Once these are loose, the trim around the inside door release handle (the one you pull to open the door) can be pryed in a backward motion. Then the entire panel can be removed by pulling upward and backward at the same time (it easier to do this with the window down). Then it is a matter of disconnecting the wires attached to the various controls for the electric windows and door locks to free up the panel itself. There is probably a plastic skin covering the metal portion of the door. Carefully pull that away to expose the inner workings of the door latch mechanisim. The rest of the procedure should become easy to figure out. I have not removed the exterior door handle itself; but it is a simple mechanism as I recall. Best of luck to you.
remove the screw behind the door panel. where you place your hand to pull the door closed there is a small plastic cover in the bottom lift this out and there are two bolts under there, remove them. then you should use a trim removal tool to pry the plastic panel away from the door. you will have to go down both sides and across the bottom. the window lift cable end has probably broken which lets the window slide down. purchase a new window motor and regulator assembly. it simply bolts in