Question about 2003 Chevrolet Monte Carlo

1 Answer

How to remove head restraint ?

How to remove head restraint? I need to install safety belt guide. thanks

Posted by on

  • nik_at_nite Nov 11, 2008

    Seat belt guide broken which supports the seat belt to the side of the seat. 2003 Chevy Monte Carlo, passenger side. Cant find any push button releases or holes which will allow me to remove the head rest in order to install a new seat belt guide holder.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

There is a small flat button in the plastic piece that sits on top of the seat. This button will release head rest

Posted on Aug 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heated and cooled seat on 2004 expedition stopped working how to reset them


Heating and the cooling both don't work ? Just one seat or all seats ?
Your best bet have it checked for DTC'S - diagnostic trouble codes to start .
Climate Controlled Seat Module (CCSM) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 ECU Is Faulted CCSM INSTALL a new CCSM and CARRY OUT programmable module installation (PMI). REFER to Climate Controlled Seat Module . B1358 Ignition Switch or Blower Electronics Circuit Short to Ground CCSM Go To Pinpoint Test Q . B2477 Module Configuration Error CCSM This DTC indicates programmable module installation (PMI) has not been done to a newly installed module. CARRY OUT PMI. REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. B2486 Climate Controlled Seat Module Voltage Out of Range CCSM DEPOWER the supplemental restraint system (SRS). REFER to Section 501-20B . DISCONNECT driver safety belt buckle pretensioner electrical connector or passenger safety belt buckle pretensioner electrical connector of the affected seat and CONNECT restraint system diagnostic tool 418-F395 to the safety belt buckle pretensioner harness connector. CONNECT the battery ground cable. CHECK circuit 294 (WH/LB) for a fault. REPAIR as needed. If okay, REFER to Section 414-01 . Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the safety belt buckle pretensioner harness connector and CONNECT the safety belt buckle pretensioner connector of the affected seat. REPOWER the SRS. REFER to Section 501-20B . B2488 Thumbwheel Switch Voltage Out of Range High CCSM Go To Pinpoint Test R . B2521 Tach Circuit Failure CCSM Go To Pinpoint Test Q . B2729 Cushion Over-Temp Detected CCSM Go To Pinpoint Test S . B2730 Back Over-Temp Detected CCSM Go To Pinpoint Test S . B2731 Differential Temperature Fault CCSM Go To Pinpoint Test S . B2792 Heat Switch Short to Ground CCSM NOTE: If HEAT is pressed for greater than 20 seconds on the climate controlled seat switch, DTC B2792 will set in the CCSM.
CLEAR the DTC. If the DTC does not clear, DEPOWER the supplemental restraint system (SRS). REFER to Section 501-20B . DISCONNECT driver safety belt buckle pretensioner electrical connector or passenger safety belt buckle pretensioner electrical connector of the affected seat and CONNECT restraint system diagnostic tool 418-F395 to the safety belt buckle pretensioner harness connector. CONNECT the battery ground cable. CHECK circuit 1551 (VT/WH) for a short to ground. REPAIR as needed. If okay, INSTALL a new climate controlled seat switch. Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the safety belt buckle pretensioner harness connector and CONNECT the safety belt buckle pretensioner connector of the affected seat. REPOWER the SRS. REFER to Section 501-20B . B2793 Cool Switch Short to Ground CCSM NOTE: If COOL is pressed for greater than 20 seconds on the climate controlled seat switch, DTC B2793 will set in the CCSM.
CLEAR the DTC. If the DTC does not clear, DEPOWER the supplemental restraint system (SRS). REFER to Section 501-20B . DISCONNECT driver safety belt buckle pretensioner electrical connector or passenger safety belt buckle pretensioner electrical connector of the affected seat and CONNECT restraint system diagnostic tool 418-F395 to the safety belt buckle pretensioner harness connector. CONNECT the battery ground cable. CHECK circuit 1550 (WH/OG) for a short to ground. REPAIR as needed. If okay, INSTALL a new climate controlled seat switch. Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the safety belt buckle pretensioner harness connector and CONNECT the safety belt buckle pretensioner connector of the affected seat. REPOWER the SRS. REFER to Section 501-20B . U2362 UBP Invalid Data Node ID CCSM NOTE: DTC U2362 indicates a network concern, the CCSM is not the source of the fault.
CLEAR the DTC. If the DTC does not clear, REFER Section 418-01 .

Nov 26, 2016 | 2004 Ford Expedition

1 Answer

How do you remove front seat head rest on 2014 jeep compass?


front left or right and why>?
may I ask why? why remove a safety device.??????
did you search first.
we just answered this last month.
did you read the operators guide in this,
lost the glove box guide already?
or want is to read it to you, ok
here again.
answering for USA cars.
page 56
got this option>
Supplemental Active Head Restraints (AHR)
wana bet THAT dont come off, unless replacing it but you never said why.
page 161
"The head restraints should only be removed by qualified
technicians, for service purposes only. If either of
the head restraints require removal, see your authorized
dealer.
• In the event of deployment of an Active Head Restraint,
refer to "Occupant Restraints/Resetting Active
Head Restraints (AHR)" in "Things To Know Before
Starting Your Vehicle" for further information."

if lost the book
its here to read 24/7 or download
read it
then say why its to be removed.

http://www.jeep.com/en/owners/manuals/

Nov 22, 2016 | 2014 Jeep Compass

1 Answer

Where are the air bag sensors on a 2000 Lincoln towncar


Sensor - Front Crash Removal
WARNING: Vehicle sensor orientation is critical for proper operation. If a vehicle equipped with an air bag supplemental restraint system (SRS) is involved in a collision, inspect the sensor mounting bracket and wiring pigtail for deformation. Replace and properly position the sensor or any other damaged supplemental restraint system (SRS) components whether or not the air bag is deployed.
WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again.
  1. Depower the system. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in this section.
  1. Remove the radiator upper sight shield (8C291).
  1. Remove the air bag sensor.
    1. Disconnect the air bag sensor electrical connector.
    1. Remove the three screws.
    1. Remove the air bag sensor.
    2. SECTION 501-20B: Supplemental Restraint System 2000 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/10/2004 Sensor - Side Crash Removal
      WARNING: Vehicle sensor orientation is critical for proper system operation. If a vehicle equipped with an air bag supplemental restraint system (SRS) is involved in a collision, inspect the sensor mounting bracket and wiring pigtail for deformation. Replace and properly position the sensor or any other damaged supplemental restraint system (SRS) components whether or not the air bag is deployed.
      WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
      WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
      NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
      NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
      NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again.
      NOTE: Left side is shown, right side is similar.
      NOTE: The side crash sensors are located under the carpet beneath the front seats.
      1. Position the seat to gain access to all fasteners.
      1. Depower the system. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in this section.
      1. Remove the front seat. For additional information, refer to Section 501-10 .
      1. Remove the safety belt anchor bolt cover.
      1. Remove the bolt and the safety belt anchor.
      1. Remove the front and rear door scuff plates.
      1. Remove the lower B-pillar trim panel.
      1. Remove the carpet to access the side crash sensor.
      1. Remove the side crash sensor.
        1. Remove the retaining bolts and position the side crash sensor in order to disconnect the electrical connector.
        1. Disconnect the electrical connector.
        1. Remove the side crash sensor and bracket.

Dec 16, 2015 | 2000 Lincoln Town Car

1 Answer

How do I remove the headrest from a 1998 Mercury Grand Marquis.


REMOVAL



  1. Unscrew front seat head rest guide rod retainers.


  2. Pull up on front seat back head restraint. Compress foam in area of front seat head rest guide rod sleeves.


  3. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.


INSTALLATION



  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.


  2. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.


  3. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.


  4. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.


  5. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.




found this helpful answer from mercury mechanic on JustAnswer com

Feb 28, 2015 | 1998 Mercury Grand Marquis

1 Answer

We need to remove the drives side head rest to install a seat cover, but we cannot figure out how to remove the head rest. How do you remove the driver's side head rest?


Head Restraints Removal
  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .

9a4d433.gif

Aug 21, 2010 | 1998 Ford Taurus

2 Answers

I had a fender bender that pushed in front bumper and blew both air bags and cruise control. i have had bumper/frame repaired and i need to know where/how many sensore need to be replaced when i replace...


you should only have to place the front crash sensor and both air bags and you may have to replace the clock spring behind the steering wheel it usually breaks after an impact i would recommend you have a qualified technician do this work

Jan 18, 2010 | 2001 Ford Escape

1 Answer

Front headrest, ford focus


Seat Backrest — Front adobe.gif Printable View (404 KB) Disassembly
All vehicles
ani_caut.gif WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
ani_caut.gif WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.
ani_caut.gif WARNING: Front seat back trim covers installed on seats equipped with side air bags cannot be repaired, they are to be replaced. Cleaning is permissible.
ani_caut.gif WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
NOTE: If a seat equipped with a seat mounted side air bag and/or a safety belt pretensioner (if equipped) system is being serviced, the supplemental restraint system (SRS) must be depowered.
NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
  1. Depower the SRS. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of Section 501-20B.
  1. Remove the head restraint.
  1. Remove the head restraint guides.
    • Using a suitable screwdriver, depress the locking tang.
    e0008398.gif

May 31, 2009 | 2004 Ford Focus

1 Answer

Audible seatbelt warning keeps on sounding on my 2005 f150 ford truck


From the F-150 Forums, since I just bought one and this worked!

This is straight from my 2009 f150 owners guide

Preperation
1. the parking brake is set
2. truck in park
3. ignition switch is in off position
4. both seat belts are unbuckled

Disable Belt-Minder
1. turn the ignition switch to the on position, DO NOT START THE ENGINE.
2. wait until the safety belt warning light turns off. (approximately 1 minute).
* step 3 must be completed within 50 secs after the safety belt warning light turns off.
3. buckle then unbuckle the seat belt nine times, ending in the seat belt unbuckled.
* after step 3 the restraint warning light, (airbag light) will turn on for three (3) seconds.
4. within approximately seven (7) seconds of the light turning off, buckle then unbuckle the safety belt.
* the restraint system warning light will flash four, (4) times per second for 3 seconds for confirmation

you can do this for the passenger side also!!!


*NOTE
in step 3. after three times buckling and unbuckling the restraint warning light lit up in my truck. SO I WENT TO THE NEXT STEP, (STEP 4). waited 3 seconds and i buckled and unbuckled.

in the buckle /unbuckle procedure do it some what slowly and watch for the light. it may not take 9 times.
__________________

May 08, 2009 | 2005 Ford F-150

1 Answer

How do you remove the headrest on a 1996 ford crown victoria?


Head Restraints Each front seat is equipped with dual-post design front seat back head restraint (611A08). The front seat back head restraint is installed as follows:
  • It travels on dual posts which have notches to engage a spring-loaded catch in the guide.
  • The front seat back spring assembly retains the front seat head rest guide rod sleeve (610A16).
  • The front seat back head restraint is adjustable from its normal position to a raised position of approximately 25 mm (1 inch).
  • Pull up on the front seat back head restraint to raise it. Pushing down will return it to its normal position.
----------------------------------------------------------------------------------------------

Removal
  1. Unscrew front seat head rest guide rod retainers (610A18).
  1. Pull up on front seat back head restraint (611A08). Compress foam in area of front seat head rest guide rod sleeves (610A16).
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.

    Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.

Mar 01, 2009 | 1996 Ford Crown Victoria

2 Answers

How do you remove headrest on a 2008 silverado?


  1. Depress the button on the inboard head restraint guide to raise the head restraint to the full up position.
  2. Insert a small diameter tool into the hole on the inboard side of the outboard head restraint guide and pull upward to remove.
Note: These are head restraints and should be left in place for safety reasons!

Nov 20, 2008 | 2008 Chevrolet Silverado 2500HD 2WD

Not finding what you are looking for?
2003 Chevrolet Monte Carlo Logo

Related Topics:

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...