Question about 1996 Chevrolet Astro

1 Answer

Indicator switch please can you help me with my indicator switch as i can`t seem to remove it.thanks rob.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
  • IFiXhouston
    IFiXhouston Aug 14, 2008

    Google everything ...

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 sentra headlights


Check fuses with a test light Rob, in the power dist center under the hood, Check the lid for fuses to each headlight , high beam and low. Next check for current at the connector after you remove one of the low beam headlights.

Feb 03, 2014 | Cars & Trucks

2 Answers

To oil press down to 0 when engine is running


Hi!!
Check Oil Pressure Switch, make sure is properly connected and working, if all seems OK, take vehicle to a Garage to have Oil Pump tested. I would recommend not to drive the vehicle if Oil Pressure Switch is or seems to be working correctly, damage to the engine and components can occur.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Jan 12, 2011 | Toyota Sequoia Cars & Trucks

1 Answer

OVER HEATING AND NO WATER IN HOSES


temp sender unit may be faulty! as this activates the fan!
Check thermostat & hoses & their clamps aswell! as you may have a leak somewhere.
check if oil is clean & not milky!
milkyness indicates head gasket leak or warped or cracked head!
Cheers Rob.

Jul 28, 2009 | Volkswagen Jetta Cars & Trucks

2 Answers

1994 Isuzu Trooper o2 sensor, and other misc. problems.


when you replace O2 the light will not go off you must follow these steps, At 90K intervals, the O2 Sensor light will illuminate. After replacing the sensor you must perform the following procedure to reset the light. 1. Remove the instrument cluster. 2. Remove the tape from the hole marked "B" on the back of the instrument cluster. 3.Find the hole marked "A" and remove the screw from that hole. 4. Install the screw in the hole marked "B". 5. Recover hole "B" with tape. 6. Reinstall instrument cover. Once you travel 90,000 more miles you get to reverse the procedure. I think they should test the water at the places those automotive engineers work at.

Jul 20, 2009 | 1994 Isuzu Trooper

2 Answers

Rear wheel noise


Brakes or bearing would be my two top choices as starters.

May 07, 2009 | GMC Sierra 1500 Cars & Trucks

1 Answer

Indicators


Seems there may be a issue with the combination switch

Jul 25, 2008 | 1988 Mercedes-Benz 190

2 Answers

Headlights


I have a 1997 Mazda 626 and my headlights go out for no reason. My highbeams seem fine so if I have to drive at night I have to drive around holding my highbeams on. Nobody can figure out the problem. I really need help on this. I need to drive my car at night and can't.

Jun 25, 2008 | 1997 Mazda 626

Not finding what you are looking for?
1996 Chevrolet Astro Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...