Question about 1992 Honda Accord

1 Answer

Odometer the odometer and tripomoder stopped working as well i had found a clip back by the thermostat housing that was apart just as it meets the clip is there a way i can bypass the clip and just have the wire connected without the clip/splitter

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 117 Answers

It depends weather its an electronic or mechanical speedo it would be best to take it to a mechanic/ dealer

Posted on Jul 01, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the thermostat housing located on a 4cyl.

Follow the top radiator hose back to the engine. Where the hose meets the engine is the housing for the thermostat.

Feb 19, 2015 | 2009 Hyundai Sonata

1 Answer

Mazda mx-5 miata problems

drain the coolant -- undo the hose clips and remove the hose --undo the bolts holding the housing on and remove the housing, Replace the housing as they are mostly aluminium and it corrodes away and are not repairable.

Jan 19, 2014 | Cars & Trucks

1 Answer

Speedometer stopped working

You probably need a new speedometer cable. It may be too old of a car to try and find one from a salvager. They periodically send the older cars to be crushed.
The cables have been known to break apart after many years of service. It is connected at the transmission and behind the instrument cluster. You have to pull the cluster out part way and reach behind to unclip the cable from the back of the speedometer housing.

Dec 27, 2013 | 1985 Volvo DL

1 Answer

How to stop squeaking breaks on my 2007 nissian maximum

Brake squeak can be from a wear indicator which is a metal clip that touches the brake disc when the pads wear thin. If there is plenty left on the brake pads removes them and cover the BACK and the top and bottom bit of the pad where it meets the housing/caliper with copper grease. NEVER APPLY where the pad front meets the disc

Oct 16, 2012 | Cars & Trucks

1 Answer

Headlamp lens cover removal, appears simple, but is it? I hate to start prying it off the clips to find out there's more than meets the eye? Thanks, Don Carter

I'm not that familiar with 1999 Town Car headlights, but your headlights do not have covers. The housing is all one piece with the bulbs screwed into the back. I wouldn't pry on any clips near the lense. If you need a replacement housing, I found this one on Ebay at:

Sep 04, 2011 | 1999 Lincoln Town Car

1 Answer


Consider replacing the VSS (Vehicle Speed Sensor). They are reasonable on eBay. It is located on your transmission (near the back almost under your thermostat housing).

Jun 17, 2010 | 1995 Honda Accord

2 Answers

How to put in a thermostat

Find the return hose from your radiator, remove the thermostat housing from the engine, (this will be located where the radiator hose meets the engine) pop the old thermostat out and replace, make sure to install the new thermostat the same way it came out, and i have noticed that some thermostats dont come with a new gasket, if not, you may be able to use the one already on your thermostat, if its not in bad shape. Hope this helps and good luck

Mar 19, 2010 | 2003 Pontiac Grand Am

1 Answer

Ford explorers speedometer just stopped working. everything else is working fine what could cause this

If your speedometer stopped working try replacing the vehicle speed sensor (VSS). This is a fairly easy task and found on the underside of the drivers side compartment near the transmission housing. It has one small retaining nut and a plug-in two wire connection. Spread the clip, pull the connection apart then pull old sensor out. Put a small bit of transmission fluid around the O ring (new). Install in reverse order. Part cost about $18.00. If that dosen't do it then the plastic gear inside the sensor housing may be worn. Hope this helps you.

Mar 10, 2010 | Ford Explorer Sport Cars & Trucks

3 Answers

Dashboard instrument cluster faulty - fuel gage, odometer, tacho and trip counter not working on my nisan n13. Fuel gage shows pessimistic eatimat of fuel in tank. Odometer stopped one year ago when the...

N13's are terrible for this problem, the odometer stops because of a faulty little nylon cog that has to be replaced, the tacho and gauges in n13 dashed die as well but as far as I know that's because of faulty electronics, if it was just the odometer problem you couldv'e bought the cog off ebay (and with a little mechanical knowledge) you could've taken the dash apart and re installed it yourself but because the other electronics are dying I advise you take it to a dash repairer or you can try getting out a soldeing iron and try to replace all the faulty connections yourself.

Feb 20, 2010 | 1990 Nissan Pulsar

1 Answer

Where is and how do i change a thermostat on a 1990 corolla?

based on my memory as i dont have the car in front of me it might help if you have the new thermostat and gasket in front of you-most cars have the thermostat inside of the metal (sometimes plastic) round housing located where the upper radiator hose meets the engine.usually 2 or 3 bolts hold it on. however quite a few cars have have the thermo. located where the lower radiator hose meets the engine.before you start pulling things apart, eyeball the upper and lower "housing connectors" and usually you can eliminate one because it will be the wrong size,depth or shape-meaning theres no way the new part will squeeze in that spot. let me know how you make out.

Aug 30, 2009 | 1990 Toyota Corolla

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides