Question about 2005 Mazda 3

1 Answer

How do I remove the rear tire. No locking nuts out of the five. I'm puzzled.

Remove rear tire?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Weld a normal nut to it, then twist off? dont understand your question

Posted on Sep 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjust handbrake 94 libero


  • Remove the center console covering the parking brake lever. Locate the parking brake lever between the drivers seat and the front passenger seat. Put the parking brake lever in the lowest position.

  • 2

    Turn the cable adjuster locknut to make the nut loose. Find the nut at the base of the parking brake lever.

  • 3

    Raise your GT rear wheels using a jack and support the rear wheels using jack stands. Remove both rear wheels using a tire iron to loosen and take off the lug nuts. Take off the tire from the rods by hand.

  • 4

    Get underneath the car and remove the rubber hole plugs from the brake rotors. Locate the rotors on the underneath inside of the wheel wells.

  • 5

    Take off the brake calipers with a screwdriver, but do not disconnect the brake fluid lines.

  • 6

    Use a pry bar to push up on the parking brake self adjuster wheel. Locate this next to the brake caliper and it looks like a star wheel. Rotate this wheel until the rotors will not turn.

  • 7

    Turn the adjuster wheel five notches in the opposite direction. Reinstall the calipers and wheels. Lower your GT using the jack and remove the jack stands from the rear wheels.


  • Sep 13, 2012 | Mitsubishi Cars & Trucks

    1 Answer

    How do I change the Rear Axle Seal on a 2002 Dodge 2500 4X4


    raise and support the pickup. remove tire. remove brake caliber. remove
    rotor. unbolt axle and remove. remove lock clip. remove axle lock nut
    2 and 9/16. pull bearing assembly. remove and replace seal. clean up
    all parts has they will prob be oily. replace lock nut (2 and 9/16) and lock
    clip, from your dodge dealer. check rear end lube when all back together
    has you will lose some.

    Jul 08, 2012 | Cars & Trucks

    1 Answer

    How do you remove the front tire on a 2008 toyota yaris?


    To remove the tire there are 4 lug nuts or even five.Thats is all that need to be removed to take the tire off. Right where the spare tire is stored are direction as for that center nut that is for the axles.leave that alone unless you are removing the axle.

    Mar 01, 2012 | 2008 Toyota Yaris Sedan

    1 Answer

    I have a 1977 Dodge. Model # M500, removing inner dually tire


    THE INNER STUDS FOR THE INNER WHEELS ARE NUTS AS WELL AND SECURE THE INNER WHEEL. USE A SQUARE DRIVE TO REMOVE THESE STUD/NUTS. DRIVER SIDE NUTS/STUD ARE LEFT HANDED(STAMPED WITH A BIG (L)). AND PASS SIDE RIGHT HANDED. THESE TORQUE SPEC OUT @ 400-450 LB FT. OF TORQUE, YOU WILL HAVE TO USE A CHEATER BAR OR HEAVY DUTY INPACT!

    Apr 26, 2010 | 1983 Dodge Pickup

    1 Answer

    How to remove the rear hub on a 1983 dodge ram 250


    Jack it up securely,take off hubcap,remove tire,remove bolts oh outside of hub,pull out axle and let oil drain, chisel down lock ring,remove nut,remove,locking device,remove second nut.Try to pull it off,If it will not come off you may need to release rear brakes.It should come off easily! Good Luck!

    Mar 21, 2010 | 1983 Dodge Pickup

    2 Answers

    Where is the tire lock kept on the 2002 RX 300


    If you are referring to the mag wheel puzzle lock, storage is an optional location. The RX300 has a number of storage pockets, so check the spare tire area and tool kit, then the rear storage side pockets, glove box, console sliding drawer at bottom of console and your map pockets on the doors. If the puzzle key is missing , go to the dealership. They will have a matching master set and can order a replacement after identifying yours.

    Nov 01, 2009 | 2002 Lexus RX 300

    3 Answers

    How can i remove tire middle bolt / nut ?


    If your talking about the nut in the front wheel, that's the axle nut and i am sure you don't want to take that out if your just trying to remove the wheel. The wheel should only have 5 wheel nuts holding it to the wheel hub. Good luck and keep me posted, be glad to help and if you are going to replace the CV joint or wheel hub, yes your going to have to remove that middle nut. 

    Aug 20, 2009 | 1999 Pontiac Sunfire

    1 Answer

    Change rear stud bolt on rear tire


    take tire off, remove drum , hammer out old one. with nut and spacers turn nut to pull stud in hole.
    If vehicle has rotor. remove tire, remove brake caliper, remove center axle nut, remove rotor. hammer out old. install new one

    Jul 27, 2009 | 2002 Dodge Caravan

    2 Answers

    Lost key to puzzle style wheel lug lock


    go to a machine shop and see if they can make you one

    May 29, 2009 | 1998 Dodge Dakota

    1 Answer

    I have a rear end seal that need replacing the one behine the drive shaft in a 1997 chev 1500 pickup truck.


    It isn't a bad job but to it you'll need an inch pound torque-o-meter and maybe a 2point puller and a seal removal and installer tool. Remove the driveshaft from the rear yoke, remove the lock-nut from the yoke, remove the yoke, remove the seal. install the new seal*must be installed evenly*. install the yoke and put the lock-nut back on !don't over tighten the lock-nut! With the brakes released (no resistence) and the tires removed. you are looking for no side to side play in bearing but also you are setting inch pounds as well. there should only be 5 inch pounds of resistence on the bearings.(this doesn't mean that you set the lock nut to inch pound, it will take maybe over 100 ft. lbs. to tighten the nut)

    Apr 26, 2009 | 1997 Chevrolet K1500

    Not finding what you are looking for?
    2005 Mazda 3 Logo

    Related Topics:

    53 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    yadayada
    yadayada

    Level 3 Expert

    61168 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...