Question about 1997 Ford Ranger SuperCab

1 Answer

Passanger side windo replacement

Passenger wingo was broken. have removed door panel, but i can not determine how to put new window in. any suggestions?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

YOUR WINDOW SHOULD SIT ON 3 TRACKS ONE BOTTOM AND ONE EACH SIDE ON THE DOOR WHERE THE CLOSING JAW IS SHOULD BE I BELIEVE A 10MM BOLT HEAD UNDO THIS BOLT THAT WILL LET THE SIDE TRACK OFF WINDOW AS FOR THE BOTTOM TRACK I BELIEVE THERES A NUT ONE EACH END UNDO THESE THAT SHOULD TAKE OFF BOTTOM TRACK PULL WINDOW OUT LEAVE TRACKS INSIDE DOOR REINSTALL NEW WINDOW HOPE THIS HELPS

Posted on Oct 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Passanger window wont roll up from driver side or passanger side


Replace the regulator. It comes with the motor. You have to remove the door panel to access it.

May 26, 2015 | 2006 Kia Sorento

1 Answer

1997 kia sportage Passenger power window stopped working from both driver's side and passanger side. Which door panel do i remove? What Next?


Sounds like the motor is bad.remove passenger panel check for voltage at motor ,if no voltage wiring is broken .if there is voltage replace motor

Jul 20, 2014 | 1997 Kia Sportage

2 Answers

2000 ford f250 passanger side window wont go up


Check the wires on the driver's door between the door and the post. A break in a wire will affect the passenger side.

Apr 04, 2012 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

I have power window switches on both the driver and passenger panels. Passanger window does not move. I checked the passanger switch and have 12 volts to switch; however, on the brown wire to the motor...


POWER GOES TO THE DRIVERS DOOR TO OPERATE BOTH ;RUNS MOTER ON PASSINGER DOOR; PASSINGER DOOR RUNS IT`S OWN POWER; CHECK CONNUITY IN THE SWITCHES AS YOU PUT THEM IN THE OFF ON POSITIONS !?

Aug 30, 2011 | 1992 Chevrolet C1500

2 Answers

Which relay switch do i replace for powers windows on 2002 ford wind star van, drivers window and back sides work passengers doesnt work i was told to replace relay I dont know whick one to replace


Doubt it is a relay,all but one window works! Are you just going to buy a new one,without knowing if it is the problem?
Check the pass window switch.
Switch,okey,remove door panel and check out motor

May 25, 2010 | 1998 Ford Windstar

1 Answer

I recently purchased a used 03 Chevy Venture van. The passenger sliding door doesn't open. It worked for 1 week and stopped. The driver side sliding door has a broken handle so I'm able to open that door...


Pain but fixable. Sounds like the linkage is not connected. Even a mechanic will have to remove the door panel and fight with it. If you can remove the rear seat from the drivers side side door then you might have room to remove the passenger side door panel to fix it. Usually clips are the first thing to break on door handle/latch linkages

Apr 06, 2010 | 2003 Chevrolet Venture Passanger

1 Answer

1990 Buick LeSabre windo is stuck open.


The door panel will have to be removed.Look for all screws and remove them.Then pull panel off gentle.The little plastic keepers will pull out,some will stay in the panel,you will have to pry the ones in the door out and place them back in the door panel before reinstalling the door panel.Look for a broken gear,or I think in this case,a broken gear tape.also the window guides(may be not all of them)will have to be replaced.Then fold around the window,and fit in the track.I really can not tell you much more,this is the best I can instruct on this item,If I can still be of help,please ask.

Aug 23, 2009 | 1990 Buick LeSabre

1 Answer

The front passenger door will open from the inside but not from the outside.


Requires removing inside panel to gain access to latching mechanism. Most likely a part has broken. Make sure window is raised. Examine all four sides of inner door panel. Look for screws and or screw caps. Remove all screws including door handle, power window and remote mirror controls. Gently pry bottom edge of panel away from door while feeling for resistance (be certain all screws are removed). When inner panel is released, raise panel up and remove. Inspect outer door and inner door latch to determine malfunction (working both controls one at a time). Replace defective parts from dealer or junk yard. Reinstall is reverse.

Jul 09, 2009 | 1992 Buick Park Avenue

1 Answer

Replace window


what do you need to know? the small passanger window or door window?
if you are replacing the door window then you need to remove the doos cover on the inside of the car. Then remove the old window base from the tracks. Slowly slide the new window in ( removing the weather stripping on one side) once the window is in roll the windoe all the way down and replace the weather stripping

Feb 02, 2009 | 1996 Mercury Grand Marquis

Not finding what you are looking for?
1997 Ford Ranger SuperCab Logo

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...