Question about 1998 Chevrolet Malibu

1 Answer

Deck installation i just installed a jvc kd pdr41 car stereo in my car and i can't figure out how to connect my second amp to it. I have the first amp for my subs connected and they work fine but i have no sound inside my car because i can't figure out how to hookup my other amp

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 740 Answers

Does you sub amp have an RCA out on it? If it does you can use that one, If not go to radio shack and pick up and rca spliter. It has two input holes white and red/ leftor right and turn it in to four outputs or 2 other channels. Good Luck.

Posted on Dec 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stereo install yukon w amp and subs


Recheck your connections from deck to "non-sub" speakers. Are you using an adapter from deck to vehicle wiring harness OR are all wires individually connected?

Apr 09, 2014 | 2002 GMC Yukon

1 Answer

Radio nissan sentra


It should work. You should get checked your car with mechanic, but I can assure you it's just a minor mistake. Cannot say anything without checking.

Mar 14, 2014 | Cars & Trucks

1 Answer

Whenever I apply my left signal turn, my screen flashes on my JVC kw av 60bt deck ,message -check for safety behind with your eyes


Did the vehicle come from the factory with a jvc stereo or did someone install it ?If the stereo was not installed by the factory whoever installed it hoooked up the power wire to the blinker power wire and if the factory did install it i would buy a new blinker relay .

Oct 19, 2012 | Cars & Trucks

1 Answer

Want to install JVC KD-HDR60 Sterio. What kind of dash kit, wiring harness, and antenna adapter do I need?


Go to best buy or some other place that sells stereos. They should have the kits.

Dec 06, 2010 | 2002 Pontiac Sunfire

2 Answers

Need to know the wires to install a deck for 97


Red is power to from ignition to cd deck
Yellow is direct power from battery to cd deck to hold the memory.
Black is ground
Blue is only needed if you are hooking up an amplifier.
I always suggest buying a wire harness quick connect system for $5, then you won't have to cut origional car wiring. If by chance you are taking the original wire route, then go to installer.com to find which wires on the car are for what.

Sep 02, 2009 | 1995 Toyota Celica

1 Answer

Retro fitted radio


i believe that car has a pre-amp in the rear speaker setup, but the clip should work fine, i would return it, they do have a 10 percent failure rate. Nothings wrong, there's just a lack of signal. If nothing else works you may have to run speaker wire from the deck to the rear. Its not bad, just takes some time and common sense, as long as you are comfortable doing that stuff, most of the platsic around where your doors go is simply clipped into place, and can be removed and replaced with relative ease, run the wires for both spkrs on the same side, get them in the trunk, and hook them direct to the speakers themselves. Good luck!

Aug 18, 2009 | 2000 Audi A4

1 Answer

I am trying to install new stereo in 2003 spyder eclipse


IF YOU GO TO WALMART AND BUY THE WIRING HOOK UP KIT THATS MADE JUST FOR YOUR TYPE OF CAR U SHOULD NOT HAVE ANY PROBLEMS.. YOU CAN DO THE AMP BYPASS, OR YOU CAN INSTALL YOU NEW DECK AND REWIRE THE SPEAKERS DIRECTLY TO THE NEW DECK.. HOPE I WAS A HELP GOOD LUCK KEITH..

Mar 11, 2009 | 2003 Mitsubishi Eclipse Spyder

2 Answers

Trying to install an in dash stereo can't figure out the speakers


depends on what wires you need the back of the raidio will have white grey green purple white is front left grey is fr green is back left and purple is back right if your lookin for truck colors get a manual or check to make sure there are no hots or grounds with a meter and twist one of the speakers ground up and with the hot touch each wire til u get sound idenitfiy the speaker wire to corect chanel

Feb 18, 2009 | 1995 Nissan Quest

1 Answer

HELP


First we need to eliminate some possible install errors,
1.) is the deck turning on.... if not check to be sure power wires are hooked up correctly ,..... if deck is turning on and speaker wires are hooked up properly, this problem is usually caused by not hooking up the power wire to the factory amp, I'm not sure what color the wire is as they are different with many types of cars, as soon as you locate the wire hook that wire to your ignition wire to your raido usually the red wire coming out of the back of the deck.... when you are finished you should have your ignition power wire feeding power to the radio and the factory amp

Jun 29, 2008 | 1998 Chevrolet Malibu

Not finding what you are looking for?
1998 Chevrolet Malibu Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...