Question about 1996 Nissan Altima

1 Answer

Finding were it is

Flasher/relay plug

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Location of turn signal flasher 2005 Ford Explorer

Posted on Aug 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2002 Chevy silverado blinker sound won't turn off


The flasher relay is probably defective. You need to replace the flasher unit. If that doesn't cure it, you have a wiring problem where the relay is getting a constant signal from the turn signal switch.
First try to unplug the flasher (it would be under the dash-follow the clicking sound) and plug it back in. If no help, replace the flasher.

Nov 27, 2012 | Cars & Trucks

1 Answer

Turn signals stopped working but were working yesterday. Any ideas?


More than likely the electronic turn signal flasher is defective.
Instructions
  1. Remove the Old Flasher Relay
    • Using your socket wrench, disconnect the negative cable from the car's battery terminal. The negative terminal and cable are identified on the top of the battery using the minus ("--") symbol. Once the cable is disconnected, wrap the metal end completely with the black electrical tape. Lay the cable down and make sure it's not touching any metal surfaces.
    • 2Open the driver side front door and kneel or position yourself so that you're able to see under the dashboard.

    • 3Locate the automotive flasher relay under the dashboard on the right-hand side. The flasher relay is about the same size as an ice cube. It will be held in place by one screw and will have a three-pronged wiring harness connected to it.
    • 4Remove the screw holding the flasher relay in place and slowly lower it from underneath the dashboard.
    • 5Hold the flasher relay in one hand, and with the other hand gently disconnect the wiring harness plug from the relay. Never separate the flasher relay by pulling the harness off by the wires, always hold the plastic harness plug itself.
    Install the New Flasher Relay
    • 6Inspect the new flasher relay to make sure it isn't damaged. Hold the new flasher relay and the old one side by side and compare them, ensuring that they are exactly the same.
    • 7Carefully plug the wiring harness connector into the new flasher relay. Make sure no other wires are intertwined as you raise the flasher and harness back into position under the dashboard.
    • 8Secure the flasher relay by returning its mounting screw.
    • 9Unwrap the negative battery cable's connector and reattach it to the car's battery terminal. Turn the power on or start your car and test out the new flasher relay to make sure it's working properly

Nov 08, 2012 | 1998 Ford Taurus

1 Answer

04 navigator flasher relay location


Contrary to other posts, the 03-05 Lincoln Navigator turn signal flasher relay is not above the ODBII diagnostic plug above the accelerator. It is in a plastic box that is located six inches above the hood release lever. The plastic cap can be prised off by wiggling and pulling up. The flasher release is the larger of the two in the relay module Due to placement, this has to be done entirely by feel.

Sep 18, 2011 | 2004 Lincoln Navigator

1 Answer

Location diagram for1996 chev blazer turn signal flasher unit


Flashers: The convenience center is used to centrally locate various buzzers, relays, flashers and/or circuit breakers. The turn signal and hazard flasher units are usually located in the convenience center located just below the instrument panel on the drivers side. Replace the flasher by unplugging the old one and plugging in the new one. Confirm proper flasher operation.

Hope helps.

Aug 16, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

Turn indicator flasher not working


this could be just a fuse or the flasher relay has blown if its the relay blown just get another relay and plug it in were the old one is the flashers should work then

Nov 15, 2009 | 2003 Kia Spectra

2 Answers

Where is the flasher relay located for 1998 Toyota 4- Runner


Toyota Pick-ups, Land Cruiser, and 4 Runner 1997-00
Flashers -REPLACEMENT

The turn signal flasher is usually located in the convenience center, under the dash, on the left side kick panel. In all cases, replacement is made by unplugging the old unit and plugging in a new one.

Hope helped with this (remember rated this help) Good luck.

Nov 09, 2009 | 1998 Toyota 4Runner

3 Answers

My blinkers will not blink they stay solid


THE INDICATOR RELAY NEEDS TO BE REPLACED

Jun 15, 2009 | 1993 Jeep Cherokee Country

1 Answer

1 directional stuck on


find location of indicators/flasher relay h/book will indicate which relay or look at fuse box/relays cover underside ? it may have diagram? try another relay? and ensure contacts are clean where relay plugs in

Oct 26, 2008 | 1995 Mitsubishi Mirage

1 Answer

Turn signals/ flasher don't work


it's called a flasher relay and is either round and silver or black and square, you can pick it up for a couple of bucks at your local auto parts store. please rate this thanks

Sep 30, 2008 | 1993 Isuzu Rodeo

1 Answer

1991 Ford E150 turn signals do not work,emergancy flashers flash constantlly unless the flasher relay is unplugged from fuse block


Hi,

If I understand you right based on your post/description, the signal lights would still turn on even if any or both of the flasher relays are removed. Should this be the case, then the signal lights are not getting the power from the flasher relays but from the brake light circuit.

Perhaps your concern is not with any of the flasher, but simply missing or loose ground more particularly with the rear lights. Perhaps you could try determining which of the wires for the brake lights and signal lights (as they come out of the light assembly) would be ground . A test and even possibly a temporary workaround is to hard wire a second ground connection from the determined ground wire of the lights and attach it to any conveniently located bolt or screw to the body. it may be to your advantage to do this on all the rear lights assembly.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 05, 2008 | 2003 Ford E150

Not finding what you are looking for?
1996 Nissan Altima Logo

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

71525 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...