Question about 1985 Ford F150

1 Answer

Oil pump do I jack the engine up or will it clear in the v6

I hear its a nightmare

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

If you have to raise the engine to remove the oil pan then you will be able to get at the oil pump it only two bolts once you have the pan off and yes its a real pain

Posted on Aug 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 dodge dakota,v6,rear main seal replacement


Did you look on youtube ? A video is worth a 1,000 words ! you may need to pull the transmission an pull the oil pan to do it . To get the oil pan off you will need to loosen the motor mounts jack up the engine so it will clear the cross member .May be !

Jul 24, 2016 | Dodge Dakota Cars & Trucks

1 Answer

I'm replacing the oil pump on my 2001 blazer with a 4.3 V6. How do I get the oil pan off without removing the entire engine from the vehicle.? What part of the engine do I place the jack under to lift


its not that straight forward as the engine is held in place by the engine mounts, so just jacking up the engine will lift the whole front end , you will need to disconnect engine from mounts and place a holding bar across the top of engine to stop it falling ,then you can jack it up , best thing for you to do is get a good workshop manual as will give you step by step instructions and will have for future reference, good luck

Oct 24, 2014 | 2001 Chevrolet Blazer

1 Answer

How do i replace oil pump on 01 monte carlo ss


If the oil pan will clear the steering components without jacking up the engine then drop the pan and unbolt the oil pump. You'll need to get a new pan gasket for the oil pan too.

Sep 25, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

I dont know how to change the oil pan


YOU'LL HAVE TO REMOVE ENGINE MOUNT BOLTS! UNBOLT OIL PAN, AND JACK UP ENGINE JUST HIGH ENOUGH TO CLEAR OIL PUMP, AND CROSSMEMBER!

Feb 20, 2011 | Eagle Talon Cars & Trucks

3 Answers

Locate the oil pump how to change it


The location of the oil pump is located inside the engine oil pan. The oil pan being on the very bottom of the engine. This would be a fairly difficult job for a beginner. Highly suggest obtaining a manual with specific directions. Disconnect battery, Make sure to remove intake plenium for clearance when jacking engine after disconnecting engine mounts, and losen only on the rear transmission mount. It will also be necessary to disconnect radiator connections hoses and transmission lines if automatic, on the safe side many people just remove the radiator all together to avoid damageing it with the engines bottom pulley when lifting/jacking engine. The engine will have to be lifted enough to facilitate the removal of the oil pan. Caution, sometimes the oil pump/ pick up screen tube assy. will have to be disconnected before the pan will clear these can just be dropped into the pan. Also, it is not uncommon to have to rotate the crank by the front pulley in order to get the cranks throws to clear the pan as well. Remember going back together you may have to slide the oil pan in place first then put the new oil pump in. This will be tight work and you may do a lot of swearing! Caution again never work in these close areas without supporting the engine on some wooden blocks! I have used short pieces of 4x4's in the past, make sure the engine is securely supported. Remember when going back together to retighten everything you loosend make a list. Before doing all this work please do an oil pressure check and not just rely on the gauge as an indicator to change the oil pump. Also, if an engine has not been serviced regularly the engine oil pan could have a build up of sluge blocking the oil pump's pickup screen therefore decreasing the oil pressure. God Bless

Sep 21, 2009 | 1993 Ford F150 SuperCab

1 Answer

Noise in right bank of V6 engine


this engine produces timing chain noises at aprox. 50.000 miles (80000kms) depending oil service intervals

Jun 10, 2009 | 2005 Suzuki Grand Vitara

3 Answers

Timing belt or chain


Ummmm woahhh hold up here...every 2.7 litre V6 i've been associated with had timing CHAINS. The chains ran the water pump and dual over head camshafts.
The 2.7l engine was manufactured by Mitsubishi for Chrysler and had an internal water pump with defective seals that allowed coolant to leak & mix with the oil causing severe sludging problems and eventual engine FAILURE...This has been a nightmare for Chrysler AND OWNERS !
MANY owners have contacted ISG Impartial Services Group 1-(866)332-3746 for a settlement with Chrysler
Attached is a cutaway view of the 2.7 litre, and as you can clearly see it is chain driven.
I've been a MOPAR enthusiast all my life...sadly, this engine was one of the worst to ever hit the streets.
Good luck Doug...i hope this helps.

2519ac2.jpg

May 26, 2009 | 1999 Dodge Intrepid

1 Answer

1998 dakota w/ 3.9 v6 blown oil pump


you may have to jack up the motor and loosen the motor mounts to get it clear and try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 19, 2009 | 1997 Dodge Dakota

2 Answers

Replace Oil Pan on 1996 Volvo 850GL


Your motor mounts may inhibit jacking the engine far enough up to clear the oil pump so it may be necessary to loosen one or more. This is not a critical point so retightening them shouldn't cause any problems.

Jan 12, 2009 | 1996 Volvo 850

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

fordexpert

Level 3 Expert

5426 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...