Question about 1997 Ford F350 Crew Cab

1 Answer

Ford f 350 xlt cab

The engine light comes on and stays, and when the codes were checked 1351 is displayed, please help!

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 98 Answers

That is your IDM circuit, install EEC-V breakoutbox (014-00950) leaving PCM disconnected measure resistance between IDM/START jack of intermittent ignition analyzer test pin. No. 48 at the breakout box. if resistance is less than 5 ohms, repair open circuit and retest. if resistance is more than 5 ohms, wiggle test roving = turn ignition off. connect PCM to breakout box. using jumper wire, connect ROVING jack of intermittent ignition analyzer to test pin No. 48 at the breakout box. turn wiggle test switch on. set MODE switch to "B". press RESET button and wait 5 seconds for initialization. if all fault memory LEDs are off, fault cannot be duplicated at this time. these are for the 4.2 through 5.4 if you need the other 2 engines just let me know and i will give you the test instructions for those either way its your IDM, im just going the extra exhausting mile of writting how to test it ; ) take care now and let me know if you get it fixed or not, throw some blue if this helped,

Posted on Sep 13, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Engine light comes on and stays on for a while then it goes off for week so.

Take to autozone or any auto parts store that will check your engine lights on for free . the code will probablty be there and my guess is it will be an o2 sensor but check to make sure. if this was helpful please leave good feed back

Feb 19, 2014 | 2006 Ford F 350 Super Duty

1 Answer

Low power and check engine light is coming on 7.3 Powerstroke Ford F-350

you need to have the code pulled out of the pcm to know were to go next in diagnosing.

Apr 28, 2011 | 1997 Ford F350 Crew Cab

1 Answer

How does one disconnect the check engine light on a 1996 ford f 150 pick up? engine light stays on and has been checked by ford repair with no insuing issues. light still remains on.

The check engine light comes on because the computer has detected a problem. You need to have the truck scanned for fault codes. Try going to Autozone or similar place to get the scan done. Once you have the codes, you can post them here for an expert to evaluate.

Oct 08, 2010 | 1996 Ford F150 Regular Cab

1 Answer

What does the wrench light mean when it comes on in the instrument panel of my 2006 f350 4x4 crew cab?

Your on board computer has detected a concern with the electronic throttle control. You need to have the codes pulled like when you have a check engine light on. If the light is staying on,the vehicle will run in a back up mode.

Jan 03, 2010 | 2006 Ford F 350 Super Duty

1 Answer

Vehicle misfire... diagnostic code is 1351

Code 1351 is for the ignition control module.Ignition control circuit high.This module is on the same bracket as the coil.Before you buy a new one.Try a salvage yard and get a used one.

Nov 19, 2009 | 1997 GMC Sierra

1 Answer

Temperature gauge barely moves and the check engine light came on and the engine is'nt hot to the touch. 2002 ford ranger xlt

sounds like you have a bad temp. sending unit. Go to a parts store and have them scan your computer and they can translate the code and tell you for sure. Check your coolant and make sure it is full and clean.

Oct 27, 2009 | 2002 Ford Ranger Regular Cab

2 Answers

Engine light on intermitting power loss

Take it to Advance auto or Auto zone, let them connect a scanner, (free of charge) , they can read the codes & most cases tell you what part or system is failing.

Sep 09, 2009 | 2007 Ford F-350 Super Duty XLT

1 Answer

My 2000 f-350 fords ABS light first flikers after start-up then stays on for a period of time. Then goes out and comes back on and stays on.

The only thing you can really do on your own is pull the wheels off and check for any obvious signs of wear or damage to sensors and circuits. Otherwise, the module will have to be scanned to pull codes for further diagnosis.

Aug 12, 2009 | 2000 Ford F350 Super Duty Super Cab

1 Answer

Where are the door pins for the door ajar light

The door ajar switches are located inside the door they are attached to the door latch assembly, they twist in, you will need to remove the rear window glass run channel to access them, this is your problem, the switches stick and cause this problem. There is a TSB concerning this problem as well.

May 14, 2009 | 1999 Ford F350 Regular Cab

Not finding what you are looking for?
1997 Ford F350 Crew Cab Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides