Do you know off hand if the bulbs can be replaced from the back or the front by removing the cover. I tried to pull it out the back and just the connector came off. I dont want to start pulling things apart until I know for sure.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Easiest way is to stick your hand in front of the battery and take the dust cover off, twist the bulb and done. I'm lucky, have smaller hands! lol, If you can't get to it, remove the battery for easy access.
The passenger side requires removal of the aircleaner box.
the head light bulb is on the back side
there is two locking pins under hood holding the assembly in
rotate 1/4 turn and pull up pull assembly put and unplug
remove retainer ring and remove bulb
assemble in reverse test new bulb before mounting light assembly back in
If your car with xenon head light you don't try to replace bulb, it's need experience hand to do it, if it's jest normal light you can replace it, first open engine hood then have a look back side of the head light you can see back cover, on the cover you can see direction have mentioned open and lock turn the cove to open direction, after that you can see the electrical socket for bulb jest pull it out then have a good look the bulb have lock by the tensioned string lock, if you have good look you can see how it's can remove, it have hookup on bottom you have to press the lock for release from locking point after release from lock you have to fold it up and take bulb out, the bulb also have center lip to fix it right position you must have good look before remove the bulb and keep it in mind, center lip must be set upward, and install revers order, is this information helped you?
REACH BEHIND HEAD LIGHT ASSEMBLY.ROTATE THE SEALING COVER COUNTERCLOCKWISE TO REMOVE IT FROM THE HEAD LIGHT HOUSING.REMOVE THE BULB LOCKING SPRING. DISCONNECT THE BULB ELECTRICAL CONNECTOR.PULL STRAIGHT OUT ON THE BULB TO REMOVE IT.BY BULBS BEING HALOGEN.DONT TOUCH WITH BARE HANDS. OIL FROM HANDS WILL CAUSE BULB TO BLOW BY OVERHEATING.HANDLE BULBS WITH CLEAN GLOVES OR NEW CLOTH GLOVES.
There is one bolt on top of the radiator support and another in back. The assy fits into a pluug that keeps it aligned so it cam be tough to remove. Just wiggle it side to side while pulling and it'll slowly come out.
Are you looking to fix the bulb that is in the corner of the headlamp? You don't need to remove the head light for that. The is a black cap that screws off just beind it.
The actual light? or just the bulb inside the light?... If you mean the whole light then pop the hood and look around the lens and you will a few screws that hold it in place. Remove and replace. If you mean the bulb, pop the hood and and look behind the light cover and you will see where the light bulb attachment screws into the back. Unscrew the attachment and remove the bulb. When you replace with the new bulb be careful to not touch the bulb with your bare hands as a chemical reaction will cause the bulb to burn out faster than normal. Put it all back together as it was before and you are good to go.
I know it sound obsured but i found the easiest way without damaging anything or your hands is to take the front bumper off, it's about two hrs work.
Really there is no easy way unless you can find somebody with really small hands and even then its hard.hope this helps
Thank you for sharing the information on the light bulb. You just saved me money from having to take my 2003 Trailblazer in to have the low beam bulb replaced. I did exactly what you said.
1 Open hood and lock.
2. Take filter cover off (4 screws and they stay with the filter).
3. 3 inch cover pulls off.
4. Twist light bulb 1/8 turn.
5. Unclip the wiring harness to light bulb assembly.
6. Test by turning light switch on.
7. Align assembly with light housing and turn 1/8 until it snaps in.
8. Put 3 inch cover back on.
9. Place filter cover back on and hand tight the 4 screws.
10. Close hood.