Question about 1994 Toyota Corolla

2 Answers

Toyota corolla changing front wheel bearing in a1994 corolla sedan

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Remove wheel, brake cliper, cliper mounting bracket, brake pads and rotor.
Remove tie rod end and strut from spindle,
Remove large drive axle nut from center of hub by removing cotter pin and nut cover
Remove the ball joints 2 nuts and 1 bolt
Pull assy. lose from drive axle.
Take complete Hub assy with new bearing to an automotive machine shop and have them disassemble hub and replace bearing.
Reverse steps to reinstall

Posted on Feb 21, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 117 Answers

Remove wheel
pop off centre cap
take out split pin
remove nut and you will be able to just pull the outer bearing out.
to get to the inner bearing you will need to take off the whole hub and do it off the car

Posted on Jun 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace steering wheel of toyota corolla 1990 model


The steering shaft has splines that allow the steering wheel to be positioned correctly with the front wheels.
Try tapping behind the streering wheel with a hammer to loosen so you can pull the steering wheel off.
If this does not work then you need a wheel puller to pull the steering wheel off the steering shaft.

Jun 10, 2012 | 1990 Toyota Corolla

1 Answer

2001 toyota corolla I have a loud roaring seens like it from the right front wheel.


THIS NOISE IS CAUSED BY A POSSIBLE WHEEL BEARING
WHEN YOU DRIVE THE VEHICLE YOU SHOULD HEAR A ROARING NOISE AND AS YOU GO FASTER THE NOISE WILL GET LOUDER AND WHEN YOU TURN THE WHEEL FROM SIDE TO SIDE THE NOISE WILL FADE IN AND OUT. THIS IS AN INDICATION THAT THE WHEEL BEARING IS BAD.
ALSO ANOTHER WAY WOULD BE TO JACK UP THE FRONT OF THE VEHICLE, BLOCK OFF THE REAR WHEELS SO THE CAR DOES NOT ROLL BACK ON YOU, THEN PUT THE CAR IN NEUTRAL AND GO TO THE WHEEL PUT YOUR HAND ON THE STRUT BASE AND SPIN THE TIRE WITH YOUR OTHER HAND YOU SHOULD FEEL A GRINDING NOISE. IF SO THE WHEEL BEARING ON THAT PARTICULAR SIDE IS BAD AND IT NEEDS TO BE CHANGED

Jan 12, 2011 | 2001 Toyota Corolla

1 Answer

Change the front wheel bearings toyota corolla 1992


front wheel bearings on this vehicle are part of a hub assy. you will have to completely remove the steering knuckle, press out the old bearing hub and rear seal and press in the new one.

Aug 03, 2009 | 1993 Toyota Corolla

1 Answer

Wheel bearing replacement left front wheel Hello Everyone, I may need to replace the wheel bearing on my right front wheel of my Corolla wagon. How can I know for sure? And how can I find out how to do...


Diagnosing the bearings can be tricky depending on severity of wear. Typically - drone noise at highway speeds, squeeling, clicking or grinding noises at low speeds that reduce during braking, or pull off the wheel and brake assembly and check the bearing for slack or smoothness of rotation by hand. While doing this, check the brake assembly thoroughly - generally a more likely culprit of wheel noise.

Wheel bearing replacement is not for the novice backyard mech. - you will need pullers, press, etc. If you can get a rebuilt assembly - much easier.

Apr 23, 2009 | 1996 Toyota Corolla

1 Answer

I want to repack front wheel bearing of my 1995 Toyota 4 door sedan. How to go about it. Thanks.


In a nutshell, you can't. They are sealed when installed and self destruct if you remove them. If they are noisy, replacement is your only option. This is not an easy job and must be taken to a good shop for this service if required.

Mar 23, 2009 | 1995 Toyota Corolla

1 Answer

Wheel bearing


HI, For replace the front wheel bearing. on a toyota corolla 03
You need a hydrualic bench.
Because they goin pressed.
I recomend go to a repair shop, is not easy.
It's take about 2 hour to do. with the right tools.

Jun 28, 2008 | 2003 Toyota Corolla

Not finding what you are looking for?
1994 Toyota Corolla Logo

707 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74418 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7254 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...