Can not remove front tire, all lug nuts removed tire will not come off

Loosen all of the nuts on the tire while it's still flat on the ground before you Jack it up Do not leave any boats Tighten while is on the ground you can actually bring them all way to the end of the stud before you jack it up

Forget removing tire from its current position. Taking it off without the right tools is next to impossible and ............

Bang the lug nuts with a nice lump hammer to loosen up any corrosion. Then try heating the nuts with a torch, and with a good pair of vise grips and and an extension for them loosen the nuts to remove the rim.

Before doing anything make sure you have air in your spare..,A good Jack and spare tire removal kit....The kit should be under or behind the passenger seat..I don't like the factory Jack it comes with because sometimes you need a good strong block of wood to achieve the height you need to contact the vehicle..and sometimes they don't work correctly...Some spare tire release tools are under the hood..It is a long skinny rod ...You have to use rod or rod kit to stick through the rear bumper at the slot and turn the rod counterclockwise after you feel the rod connect with the release mechanism..,Lower the spare until it touches the ground then keep turning so you can have enough slack to remove cable from spare tire...Set parking brake while in park and use the lug nut removal tool to break loose the lug nuts before raising vehicle..They are removed counter clockwise..Don't take nuts off just break them loose...Block front wheels for safety with anything solid you can find if you are stranded..If you can't find anything rely on parking brake..It should be safe in park but safety first....Jack vehicle up..,remove all lug nuts put them in a safe clean place don't lose them..Remove flat tire..Install spare..Start each lug nut and tighten them all tight by hand..Snug each nut clockwise in a star pattern ..Get them good and tight but don't try to hurt yourself or break the stud...Lower vehicle,remove Jack..Snug each lug nut once again for safety..Put flat in truck bed for now rather than back in the spare storage area because it has to be repaired..Crank spare cable that held spare under truck clockwise until it stops.Remove tool..,Gather all tools used., remove blocks from front tires.,Head to a tire store...

The large nut you see is most likely the axle retention nut.

It is NOT used to hold on the wheel.

The wheels on a 2000 Acura TL are secured to the wheel hub by 5 lug nuts.

If after removing the "lugs" the tire and wheel may be difficult to remove after a long period due to corrosion betweem the wheel and hub.

If this happens, tap the tire at opposite ends (like 12 and 6 o'clock) with a rubber or plastic mallet.

This should help to loosen the wheel so you can remove it.

remove wheel cover then with tire on the ground just loosen lug nuts just a little dont remove lug nuts then safely raise support vechicle.then remove front tires.

jack up vehicle, remove tire. knock out old stud with a hammer and punch. put new stud in from back if need be. to draw it up tight.use a lug nut with something under it so when you tighten the nut it brings the stud into position. remove the nut you put on. and replace the tire. good-day! if the brakes and rotor are in the way. you will have to remove them to replace the wheel stud.

Only the four wheel lug nuts need to be removed to get the rim and tire off the car. That large center nut holds in the front axle shaft.

Loosen tire lug nuts. Jack up the car and remove lug nuts and tire. Remove two bolts holding the caliper in place. Remove the the two bolts holding pads in place. Hang caliper with a wire from wheel so brake line is not stressed. Mount new calipers in correctly and tigthen pad bolts. Put caliper on and tighten caliper bolts. Replace tire and lugs nuts. Jack car down and tigheten lug nuts.

turn lug nuts counter clockwise while the tires are still on the ground then raise the front end and take off loose lug nuts and wheels. reverse steps when done

The owners manual shows where to put the jack. I no manual sometimes there are illustrations where the jack is stored in its compartment. First loosen the lug nuts before you jack up the vehicle, prevents the tire from turning. After jacking up the vehicle finish removing the lug nuts then remove the tire. The spare tire on the door may have a locking lug nut which requires a key to unlock before removing the lug nuts. Key us usually on the ignition key ring. Remove the lug nuts and put tire on the drivers side. Tighten up the nuts on the wheel and after the car is let down from the jack, finish tightening the lug nuts.