Question about 1995 Toyota Camry

1 Answer

Head Gasket I need to know the order in which, I need to follow to replace a head Gasket

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,010 Answers

Replacing a head gasket is not a DIY job, unless the person has plenty of experience, knowledge, and the proper tools. The fact that a person would even ask, "How to replace a head gasket", would indicate to some that they should not trying to do that repair.
To replace a head gasket you must remove the intake manifold, exhaust manifold, valve train, and then the head. This is very involved and requires disconnecting lots of sensors and the ignition system. The head must then be checked to see if it is warped, or cracked, and repaired if necessary. You must then know how to put all this back together and torque all the bolts in the proper sequence. This takes training and skill which the average shade tree mechanic does not have.
There is a difference between say a over head cam (OHC) engine and a internal cam engine. And then if it is a V6 or V8 then both head gaskets must be replaced even if only one blew. And last but not least, you have to find out if there is other engine damage and what caused it to blow the gasket in the first place. Definitely not for an amateur.
The best answer to this question: Take it to a professional.
The second-best answer: Get a repair manual and follow directions. A repair manual does not provide the training necessary to do this repair correctly, and not near enough information, but it can provide more info than can be written out in an answer like this.
Below is the best answer we can provide in this format.
Parts
Exhaust flange nuts and bolts
Head Gasket (preferably OEM)
Ten head bolts
Two valve cover end seals
Tube of RTV silicone

Disassembly
1. Disconnect the battery negative terminal
2. Drain the cooling system
3. Raise the front of the vehicle and support it with jack stands .
4. Remove the two 13mm exhaust bolts holding the exhaust pipe to the exhaust manifold, lower the vehicle
5. Remove the air cleaner assembly
6. Remove the upper radiator hose
7. Loosen the 13mm nut holding the dipstick tube bracket to the thermostat housing and remove the coil (if it is attached to the thermostat housing) and unplug the coolant temperature sensor
8. Remove the spark plug wires from the plugs, remove the distributor water shield and the distributor cap (this step is so you don't damage the distributor cap).
9. Remove the two uppermost 15mm-head bolts from the top of the a/c , alternator bracket where it attaches to the head and unplug the single wire temperature sending unit
10. Remove the upper half of the timing belt cover
11. Remove the valve cover
12. Disconnect the wiring harness connector that is just to the right of the throttle body
13. Disconnect the throttle cables from the throttle body and remove the two 10mm head bolts holding the bracket
14. Disconnect the vacuum lines from the throttle body
15. Disconnect the fuel lines - NOTE : The fuel lines may be under pressure , use extreme care when removing them
16. Disconnect the throttle position sensor connector and the EGR valve connector (if equipped)
17. Carefully lift up the throttle body wiring harness , the fuel lines , and the vacuum lines together and use a bungee cord to hold them out of the way
18. Remove the ground strap that is attached to the intake manifold from the fire wall
19. Remove the 15mm-head bolt holding the battery ground cable to the engine
20. Disconnect the vacuum hose from the power brake booster and the heater hose from the intake manifold left side
21. Use two plastic tie straps to secure the timing belt to the camshaft pulley and remove the pulley . Hold upward tension on the pulley and secure it with a bungee cord to the right hood hinge - NOTE: be sure to hold the upward tension with the bungee cord so the timing belt doesn't jump a tooth on the lower pulleys
22. Remove the head bolts and lift the head off the engine block . (I suggest having an assistant help to lift off the head) With the head removed , carefully check the head casting for signs of cracks. Also use a straight edge to check the head casting for warpage (maximum allowable warpage is .00
23. Clean all the head gasket mating surfaces and wipe clean with a little brake cleaner on a rag. Use a round plastic bristled brush to clean out the head bolt holes in the engine block and blow them out with compressed air .

Reassembly
1. After the gasket surfaces are prepared, set the new head gasket in place and CAREFULLY place the head into position, take extreme care not to place the head on the head gasket until it is in the proper position.
2. With the head in place, install the head bolts. You will need to tighten the head bolts in a circular pattern starting from the center and working your way out. I recommend hand tightening all the bolts before beginning the torque sequence. Head bolt torque: For older style 10mm head bolts : 35 - 45 - 45 - and a 1/4 turn; For newer style 11mm head bolts : 45 - 65 - 65 - and a 1/4 turn
3. Use the two rubber valve cover end seals and a bead of RTV silicone to reseal the valve cover.
4. Do Not let the silicone skin-over before setting the valve cover into place and tightening the bolts, also be sure that both mating surfaces of the valve cover are clean and oil free .
5. After the head is reassembled you will need to reset the base timing to specs. You will also want to double check the timing belt position . Use a variable timing light and set the timing mark on zero degrees . Save the setting on the timing light and shine it through the inspection hole in the top of the upper timing belt cover . If the belt timing is correct , you will see the oblong hole in the camshaft sprocket centered in the inspection hole .
Other Answers
Here is what other FAQ Farmers have contributed:

  • Water is a by product of combustion, therefore water dripping from the exhaust should be an indication that your engine is operating efficiently, especially if there is no sign of water in your oil. There are other signals that would indicate a blown head gasket, such as loss of compression/loss of power, unexplained coolant loss, and clouds of white smoke from your exhaust, especially noticeable upon acceleration. Overpressurizing of the cooling system can also result in overheating.

  • A lot more information is needed. For example, what kind of car is it, etc. This is a major service and should be done by an experienced technician.

  • The short answer: Remove the head, check the head for warp-age and cracks, and install a new gasket.

  • This depends on the type of engine that you have. You will need a well stocked tool box which must include a torque wrench. Import car engines will require a good selection of metric tools. You will need to drain and recycle the engine oil and coolant. It is best to rotate the engine so that the piston in number one cylinder is at top dead center of the compression stroke. At this point, take careful note of the position of the distributor rotor and make match marks as necessary so that it can be realingned when it is reassembled into the engine. Older American made V8 engines will usually require the removal of the intake manifold, exhaust manifolds,ignition distributor and associated wiring harnesses. If you are replacing the head gasket on an engine with dual overhead cams, the situiation is complicated by having to remove timing chain covers, cams and timing chains. These parts must be replaced exactly as they were removed. Manifold and cylinder head bolts should be removed in the reverse of the installation and torque sequence to avoid warping and possible cracking. This is especially important when dealing with aluminum parts. The cylinder head bolts must be tightened and torqued in a specified sequence and Foot/pound specification as per the engine manufaturer. The best advice would be to obtain a maintenance manual for the vehicle you intend to service. Most aftermarket parts dealers either stock or can order this for you. In the manual you will usually find step by step instructions that are for the specific engine/vehicle that you are servicing.

  • Before attempting a gasket replacement you should consider what else might be done. Since it requires removing the exhaust header, intake and cylinder head from your car, you might want to see what other work needs to be done at the same time. The first thing is do a check up on your car: 1. Check spark plugs to see what they tell you about the condition of the engine. 2. Do a compression check. Then determine why it failed and what you need to rebuild. If you take the cylinder head off then you might want to replace it with a rebuilt one. Or at least get a valve job done. If you decide to do this yourself ensure you either rent all the tools or purchase them. For the first timers I would recommend a rebuilt head they will run between $150-$300 with a core exchange. Or you can bring it to a local shop and expect to pay around $150-$250 for labor and parts to have your rebuilt.

Posted on Jul 01, 2008

  • allanzodiac Dec 29, 2010

    An amazing and very helpful reply from chiquititas. I have a 1992 Windom, with a blown head gasket (similar engine to a camry) and have been pondering the thought of replacing the head gaskets , which I realised wasnt an easy job to do (not like the cars I drove in my youth, when it was a simple job to do)
    So after reading Chiquititas`s reply, he`s saved me a lot of time and stress, and skinned knuckles, and lots of money too,in even trying to do a head job as complicated as that.
    So rather than even contemplate doing the job, sending the car to the wrecking yard seems to be the best option for me, and they are even paying up to $500 for cars to wreck, in New Zealand, these days.

    Cheers, and thanks, Chiq,
    Allan

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bolt torque sequence on 1991 jaguar xj6 4.0 intake manifold?


intake manifold or head gasket? i know head gasket need a sequential order followed by how many degrees and Lbs of pressure. if its on the intake i doubt it needs an specific torque. just try not to crack the intake manifold since its made of plastic.

Oct 29, 2012 | 1991 Jaguar XJ6

1 Answer

Fix head gasket


For leaking head gasket it has to be replaced. For head gasket leaking and other troubleshooting, there are help links provided. Its suggested to click the link below and go through the troubleshooting procedure to confirm the issue :-----Leaking head gaskets? http://schematicsdiagram.blogspot.com/2011/12/leaking-head-gaskets.html
-----------Water in engine oil? http://schematicsdiagram.blogspot.com/2011/12/water-in-engine-oil.html
-----------How to replace head gasket on car?http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-head-gasket-on-1994.html-------------How to know what is faulty Cylinder head or Head gasket?http://schematicsdiagram.blogspot.com/2011/12/how-to-know-what-is-faulty-cylinder.html
-------------- Can I just replace Head Gasket on 1991 Buick Century?http://schematicsdiagram.blogspot.com/2011/12/can-i-just-replace-head-gasket-on-1991.html Location of Head Gasket ?

http://schematicsdiagram.blogspot.com/2011/12/location-of-head-gasket-on-1994-grand.html

------------------------
HOW TO REPLACE A HEAD GASKET

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-head-gasket.html

----------------
How to replace Exhaust Manifold?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-exhaust-manifold-on.html

-------------------
How to replace Intake Manifold?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-intake-manifold-on-acura.html

---------------
How to replace Cylinder Head ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-cylinder-head-on-acura.html

---------
Is it Easy to replace head gasket?

http://schematicsdiagram.blogspot.com/2011/12/is-it-easy-to-replace-head-gasket-on.html

------------
Should I only replace head gaskets or complete head gasket assembly?http://schematicsdiagram.blogspot.com/2011/12/should-i-only-replace-head-gaskets-or.html


---------

This will help. Thanks.

Feb 27, 2012 | Renault Cars & Trucks

1 Answer

Oil leak from head gasket can it be replaced


For leaking head gasket it has to be replaced.For head gasket leaking and other troubleshooting,there are help links provided.Its suggested to click the link below and go through the troubleshooting procedure to confirm the issue :-----Leaking head gaskets? http://schematicsdiagram.blogspot.com/2011/12/leaking-head-gaskets.html
-----------Water in engine oil? http://schematicsdiagram.blogspot.com/2011/12/water-in-engine-oil.html
-----------How to replace head gasket on car? http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-head-gasket-on-1994.html-------------How to know what is faulty Cylinder head or Head gasket? http://schematicsdiagram.blogspot.com/2011/12/how-to-know-what-is-faulty-cylinder.html
-------------- Can I just replace Head Gasket on 1991 Buick Century? http://schematicsdiagram.blogspot.com/2011/12/can-i-just-replace-head-gasket-on-1991.html Location of Head Gasket ?

http://schematicsdiagram.blogspot.com/2011/12/location-of-head-gasket-on-1994-grand.html

------------------------
HOW TO REPLACE A HEAD GASKET

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-head-gasket.html

----------------
How to replace Exhaust Manifold?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-exhaust-manifold-on.html

-------------------
How to replace Intake Manifold?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-intake-manifold-on-acura.html

---------------
How to replace Cylinder Head ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-cylinder-head-on-acura.html

---------
Is it Easy to replace head gasket?

http://schematicsdiagram.blogspot.com/2011/12/is-it-easy-to-replace-head-gasket-on.html

------------
Should I only replace head gaskets or complete head gasket assembly? http://schematicsdiagram.blogspot.com/2011/12/should-i-only-replace-head-gaskets-or.html
-----------FOR oil leak issue check the following help links:---Common Causes of Car Oil Leaks? http://schematicsdiagram.blogspot.com/2011/12/common-causes-of-car-oil-leaks.html --------Troubleshoot Car Oil leak? http://schematicsdiagram.blogspot.com/2011/12/troubleshoot-car-oil-leak.html
---------Car oil leak?

http://schematicsdiagram.blogspot.com/2011/12/car-oil-leak.html

---------
Car oil leaks from valve cover gasket? http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html
---------This will help.Thanks.

Jan 30, 2012 | 2006 Scion tC

2 Answers

Oil leak from head gasket


For leaking head gasket it has to be replaced.For head gasket leaking and other troubleshooting,there are help links provided.Its suggested to click the link below and go through the troubleshooting procedure to confirm the issue :-----Leaking head gaskets? http://schematicsdiagram.blogspot.com/2011/12/leaking-head-gaskets.html
-----------Water in engine oil? http://schematicsdiagram.blogspot.com/2011/12/water-in-engine-oil.html
-----------How to replace head gasket on car?http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-head-gasket-on-1994.html-------------How to know what is faulty Cylinder head or Head gasket?http://schematicsdiagram.blogspot.com/2011/12/how-to-know-what-is-faulty-cylinder.html
-------------- Can I just replace Head Gasket on 1991 Buick Century?http://schematicsdiagram.blogspot.com/2011/12/can-i-just-replace-head-gasket-on-1991.html Location of Head Gasket ?

http://schematicsdiagram.blogspot.com/2011/12/location-of-head-gasket-on-1994-grand.html

------------------------
HOW TO REPLACE A HEAD GASKET

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-head-gasket.html

----------------
How to replace Exhaust Manifold?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-exhaust-manifold-on.html

-------------------
How to replace Intake Manifold?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-intake-manifold-on-acura.html

---------------
How to replace Cylinder Head ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-cylinder-head-on-acura.html

---------
Is it Easy to replace head gasket?

http://schematicsdiagram.blogspot.com/2011/12/is-it-easy-to-replace-head-gasket-on.html

------------
Should I only replace head gaskets or complete head gasket assembly?http://schematicsdiagram.blogspot.com/2011/12/should-i-only-replace-head-gaskets-or.html
-----------FOR oil leak issue check the following help links:---Common Causes of Car Oil Leaks? http://schematicsdiagram.blogspot.com/2011/12/common-causes-of-car-oil-leaks.html --------Troubleshoot Car Oil leak?http://schematicsdiagram.blogspot.com/2011/12/troubleshoot-car-oil-leak.html
---------Car oil leak?

http://schematicsdiagram.blogspot.com/2011/12/car-oil-leak.html

---------
Car oil leaks from valve cover gasket?http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html
---------This will help.Thanks.

Jan 30, 2012 | 2006 Scion tC

1 Answer

Replaceing head gasket


For leaking head gasket it has to be replaced.For head gasket leaking and other troubleshooting,there are help links provided.Its suggested to click the link below and go through the troubleshooting procedure to confirm the issue :-----Leaking head gaskets? http://schematicsdiagram.blogspot.com/2011/12/leaking-head-gaskets.html
-----------Water in engine oil? http://schematicsdiagram.blogspot.com/2011/12/water-in-engine-oil.html
-----------How to replace head gasket on car?http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-head-gasket-on-1994.html-------------How to know what is faulty Cylinder head or Head gasket?http://schematicsdiagram.blogspot.com/2011/12/how-to-know-what-is-faulty-cylinder.html
-------------- Can I just replace Head Gasket on 1991 Buick Century?http://schematicsdiagram.blogspot.com/2011/12/can-i-just-replace-head-gasket-on-1991.html Location of Head Gasket ?

http://schematicsdiagram.blogspot.com/2011/12/location-of-head-gasket-on-1994-grand.html

------------------------
HOW TO REPLACE A HEAD GASKET

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-head-gasket.html

----------------
How to replace Exhaust Manifold?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-exhaust-manifold-on.html

-------------------
How to replace Intake Manifold?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-intake-manifold-on-acura.html

---------------
How to replace Cylinder Head ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-cylinder-head-on-acura.html

---------
Is it Easy to replace head gasket?

http://schematicsdiagram.blogspot.com/2011/12/is-it-easy-to-replace-head-gasket-on.html

------------
Should I only replace head gaskets or complete head gasket assembly?http://schematicsdiagram.blogspot.com/2011/12/should-i-only-replace-head-gaskets-or.html

---------This will help.Thanks.

Jan 28, 2012 | 2002 Kia Sportage

1 Answer

Head gasket


For leaking head gasket it has to be replaced.For head gasket leaking and other troubleshooting,there are help links provided.Its suggested to click the link below and go through the troubleshooting procedure to confirm the issue :-----



Leaking head gaskets?

http://schematicsdiagram.blogspot.com/2011/12/leaking-head-gaskets.html
-----------Water in engine oil? http://schematicsdiagram.blogspot.com/2011/12/water-in-engine-oil.html
-----------How to replace head gasket on car?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-head-gasket-on-1994.html-------------

How to know what is faulty Cylinder head or Head gasket?

http://schematicsdiagram.blogspot.com/2011/12/how-to-know-what-is-faulty-cylinder.html
--------------

Can I just replace Head Gasket on 1991 Buick Century?

http://schematicsdiagram.blogspot.com/2011/12/can-i-just-replace-head-gasket-on-1991.html

-----------

Location of Head Gasket ?

http://schematicsdiagram.blogspot.com/2011/12/location-of-head-gasket-on-1994-grand.html

------------------------
HOW TO REPLACE A HEAD GASKET

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-head-gasket.html

----------------
How to replace Exhaust Manifold?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-exhaust-manifold-on.html

-------------------
How to replace Intake Manifold?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-intake-manifold-on-acura.html

---------------
How to replace Cylinder Head ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-cylinder-head-on-acura.html

---------
Is it Easy to replace head gasket?

http://schematicsdiagram.blogspot.com/2011/12/is-it-easy-to-replace-head-gasket-on.html

------------
Should I only replace head gaskets or complete head gasket assembly?

http://schematicsdiagram.blogspot.com/2011/12/should-i-only-replace-head-gaskets-or.html

---------This will help.Thanks.

Jan 27, 2012 | 1992 Plymouth Voyager

1 Answer

Hi can you tell me how much torque spectification to replace head gasket bolts, camshaft caps bolts, and camshaft pully bolts for 1994 GS 300 lexus Thank you very much for your help



  1. 60293.gif

    Cylinder head bolt tightening sequence - 1993-97

  2. Remove the head from the engine. If prying is necessary, use a protected blade; take great care not to damage the mating surfaces of the head and block.

  3. Clean the head and block of all gasket material. Take great care not to gouge or scratch the mating surfaces.

To install:

  1. Place a new gasket on the cylinder block. Make sure it is positioned correctly. Install the cylinder head in position.

  2. Lightly coat the head bolt threads and plate washers with engine oil. Install the bolts in the head.

  3. Uniformly tighten the head bolts in several passes in sequence, to 25 ft. lbs. (34 Nm).

  4. Mark the front of each bolt with a dot of paint. Following the correct order, tighten each bolt an additional 90 degrees. When complete, all the paint marks should face to the side of the engine.

  5. Again following the correct order, tighten the bolts another 90 degrees of rotation. When complete, the paint marks should face the rear of the engine, exactly 180 degrees away from the original starting point. Correct bolt torque is expressed as 25 ft. lbs. (34 Nm) + 90° + 90°.


Jan 07, 2011 | 1994 Lexus GS 300

1 Answer

At 115,000 my 4 cyl is leaking coolant into #4 cyl, no detectable coolant in oil,no oil in coolant. I assume head gasket problem. I need advice and opinion and recommendation of what manual to purchase so...


tricky job ...but ok ..just make sure you lock the cam gears if its 16 valve, sometimes you can use a wine cork if you dont have the tool , just put it between the cam s to prevent it from spinning inward ,,when reassembling after the following, so you can keep timing right while you replace the belt ....make sure you replace the belt dont reuse it...while your in there replace the water pump as well if it runs off the timing belt....its due with 115k....as well as cam seals head gasket valve cover gasket kit...intake manafold gasket..exuast gasket....also it is recommended that you replace head bolts in order to get the best tork spec.....and make sure the timing marks are correct and that your top dead center on the compression stroke #1 cylinder.....since thers no oil in the radiator its probly just a head gasket ..but send the head out have it magnaflexed check for cracks and have it decked ..milded flat if needed..it may be warped just alittle...you never know but after all that work you want to be sure...you cuold also replace front main seal while your in there...and valve seals on the head since its off anyway napa charges about 180.00 to redue the head..goodidea........

Jan 05, 2011 | 1992 Toyota Pickup

2 Answers

How big of a hassle would it be to repair a blown head gasket


That depends on several factors:
1. How much time do you have to accomplish the repair?
2. How much experience - hands on - do you have on your car?
3. Do you have the repair manual for this year/make?
4. Do you have the necessary tools and place to perform it?

If you're sure it's a blown head gasket, are the replacement gaskets available (check online with autozone - they have an instock/availability feature)? Without indepth knowledge of your situation (referenced above 1-4) a best guess would be an entire day from start to finish 8am - 10pm if you're inexperienced with the car, but determined and knowledgeable with the required tools. You shouldn't need anything out of the ordinary - just sockets/wrenches etc, a good light and the service manual for a step by step. It would be worth your while to get the service manual anyway and look through the necessary steps so that you'll be able to make an informed decision yourself. Any service manual will give the steps in order required to perform the head gasket replacement. One further question; How do you know you have a blown head gasket? Is it visibly leaking to the outside? Have you performed a compression check and you get leakeage to an adjacent cylinder? Best advice is to purchase the manual (or check one out from your local library - they've always had the one I wanted - before I bought it). The manuals have instructions for troubleshooting this kind of issue. Good luck!

Sep 23, 2010 | 1992 Acura Legend

1 Answer

Head gasket?


You remove air filter and other parts.
Then you remove head cover.
Then you unscrew and remove the head,
Clean a bit the block
Replace gasket.
Screw back the head
Follow head tourqe settings and screw orders on diagrams when mounting back the head.

The whole thing is not thst easy as it may seem, if you want to DIY you will need to buy the Haynes manual for your car. There you find a step by step procedure with pictures.

Here is a repair manual.

Also enquiry to Haynes.Haynes manuals are the best.

Here is how to replace head gasket on a Honda,
with lots of pics, procedure is the same, torque values and screwing order are different. It is not a job for absolute beginners


Do not forget to rate the solution

Thanks.

Aug 31, 2008 | 2000 Daewoo Leganza

Not finding what you are looking for?
1995 Toyota Camry Logo

867 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...