Question about 2000 Jeep Grand Cherokee

1 Answer

Driver Door After removing a security box provided by my auto dealer from underneath the steering wheel my driver door want register as being close, all the lights stay on in the car and all function are lost to every door panel. i connected the only wire that dealer had cut when removing their device.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 232 Answers

THE INSTALLATION OF SECURITY SYSTEMS ON CHEROKEES IS A RATHER COMPLEX INSTALLATION, IT REQUIRES A LOT OF WIRES TO BE ALTERED FOR IT TO WORK PROPERLY, THERE R MORE WIRE AND ADDITIONAL PARTS THAT MUST BE REMOVED FOR THE SYSTEM TO WORK CORRECTLY, TAKE THE VEHICLE TO A CAR AUDIO INSTALLATION SHOP FOR FURTHER REPAIR

Posted on Aug 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I used csorb's instructions to reprogram a master key for my 2000 Lexus RX300. The ignition works perfectly, but the doors don't lock or unlock.


Hi!!
I believe your alarm is in the PASSIVE MODE, here is how it works.

PASSIVE MODE Setting (Arming) Anti-Theft System The system will automatically set 30 seconds after following methods are performed: Remove ignition key from ignition switch. Exit vehicle, and close all doors. After performing this, anti-theft indicator on left side of instrument panel will light continuously for about 30 seconds. After 30 seconds, anti-theft indicator will blink once per second. When system is set, doors cannot be locked or unlocked using door lock control switch.
CANCELING THE ALARM AND REPROGRAMING MAY SOLVE YOUR PROBLEM.
Canceling Anti-Theft System Setting (No Alarm) When system is set (armed), but alarm is not sounding, use one of following methods to cancel system setting:
  • Unlock left or right front door using key.
  • Unlock all doors using remote keyless entry system.
  • Insert key in ignition switch and turn to ON position (this is operative only when anti-theft system has not been triggered).
HERE IS HOW TO REPROGRAM THE ALARM IN CASE YOU NEED TO RESET IT.
PROGRAMMING
PASSIVE MODE NOTE:Initial mode is passive mode off. If there is a different signal in middle of programming, signal is invalid.
Programming Passive Mode Off
  • Remove ignition key from ignition key cylinder. Ensure all doors (including back door) and engine hood are closed and unlocked. Perform all of following methods within 30 seconds:
  • Lock or unlock any door with key or remote keyless entry system.
  • Open driver door.
  • Lock and unlock driver door lock knob 3 times.
  • After performing this, system should start force lock after 2 seconds. Perform all of following methods within 20 seconds:
  • Unlock driver door lock knob.
  • Close and open driver door 2 times.
  • Lock and unlock driver door lock knob.
  • After performing this, system should start force lock after 2 seconds. Passive mode should now be off.
Programming Passive Mode On
  • Remove ignition key from key cylinder. Ensure all doors, engine hood and luggage compartment door are closed and unlocked. Perform all of following methods within 30 seconds:
  • Lock or unlock any door with key or remote keyless entry system.
  • Open driver door.
  • Lock and unlock driver door lock knob 3 times.
  • After performing this, system should start force lock after 2 seconds. Perform all of following methods within 20 seconds:
  • Unlock driver door lock knob.
  • Close and open driver door 4 times.
  • Lock and unlock driver door lock knob.
  • After performing this, system should start force lock after 2 seconds. Passive mode should now be on.
If you need further assistance, please provide an email address to send more info on your security system
Good Luck!! A 4 THUMBS UP rating would be greatly appreciated for this solution. Thank you for using FixYa!!

Mar 01, 2011 | Lexus RX 300 Cars & Trucks

1 Answer

The auto door lock, side mirror, and "driver 1/driver 2" auto controls don't work on the driver side. The power windows do work on the driver side. The auto door lock works on the passenger...


I have the same problem only now the door won't register that it is even closing! So I have to drive with the door ajar light on, and the inside lights stay on too unless I turn off all the paneling lights. I am not sure what is going on. But I am taking it into the shop on Monday to find out what is going on. I could handle not having my controls on the driver side, but this door thing is wigging me out! Hope you get yours fixed

Dec 29, 2010 | 2004 Dodge Durango

1 Answer

Where can i find fuses for my 1994 lexus sc 300


there are two fuse boxes. One is under the hood, a long black box with a removable lid on the driver's side, above the wheel well. The second is also on the driver's side, inside the car, close to the door; left side of steering wheel on the under side of the dashboard behind a hinged pocket-door that comes out if you open the pocket-door and pull gently it up and out, which allows the pocket-door to snap out of the hinge detents. At which point you'll see the fuses hiding behind.

Sep 11, 2010 | Lexus SC 300 Cars & Trucks

1 Answer

What battery do i need for a 1999 323 key fob


It should be a CR2025 battery, u will also need to program the remote again.
REMOTE PROGRAMMING PROCEDURE:
Preparation
1. Close all doors, trunk, and hood.
2. The security system must be in disarm mode and key must be removed from the ignition key slot.

Enter Code learning mode
3. Open trunk and leave it opened.
4. Open the driver's door and sit in the driver's seat.
5. Close the driver's door.
6. Cycle ignition switch 5 times between Off and On (DO NOT START ENGINE, just quickly turn key to the position that illuminates all of the lights in the instrument cluster 5 times.)
The red status light will illuminate continuously, and the siren will chirp once to indicate that the code learning mode has been initiated.
The ignition switch cycling must be performed within 10 seconds.
The sequence in steps 1-6 must be performed within 45 seconds.

Register/Delete ID Code(s)
7. Open driver's door (remain seated in driver's seat.)
8. Close driver's door.
9. Press and release any button on the remote you wish to register into the system. The status led will shut off momentarily to indicate that one ID code has been registered.
10. Repeat steps 7 to 9 to register the remain the ID codes (remotes).

Exiting code learning mode
11. Open driver's door and exit vehicle, leaving the door open.
12. Close trunk.
13. Close driver’s door. The LED will turn off and the siren will chirp

Mar 15, 2010 | 1999 BMW 323 Series

1 Answer

Windows will not work from drivers side master switch or the single door switches lock not working also remote mirrors dont 2001 jeep grand cherokee ltd


First thing to check is the fuses. Look underneath the drivers side steering wheel (to the left) for a covered fuse box. Remove the cover and find the fuse that controls the locks and windows and mirrors (two-three separate fuses) Pull them out "one by one" and see if they are burned out. If they are, replace them with the correct number fuse.If it is not the fuse, the door lock actuator has failed (for the door locks) or the master switch that controls the locks is bad. Go to your local junk yard and find a replacement for cheap

http://forums.automotive.com/70/16389/general-auto-repair/2001-jeep-grand-cherokee-power-windows-defect/index.html

Feb 17, 2010 | Jeep Grand Cherokee Cars & Trucks

1 Answer

I just need to know where the fuse box is located that holds the fuse for the turn signals for a 96 monte carlo, found the two underneath the hood but did not contain the fuse i was looking for. i looked...


you have to remove the cover on the drivers side or passenger side of the dash, the part that the door closes on. it should have a hole in it and say fuses on it

Oct 30, 2009 | Chevrolet Monte Carlo Cars & Trucks

2 Answers

Navigation screen 07 Denali is black?


THERE IS USUALLY A FUSE BEHIND THE UNIT IT SELF AND CHECK YOUR FUSE BOX

IT MIGHT BE UNDER THE STEERING WHEEL CLOSER TO THE DRIVER DOOR OR UNDER THE HOOD CLOSE TO THE BATTERY OR ACROSS ON THE PASSENGER SIDE

Jul 19, 2009 | 2007 GMC Yukon

2 Answers

Alarm wont disarm and unlocking doors does not work any suggestions?


I just had the same problem with my 1995.. believe me its a pain! by the way on the driver side below the steering wheel close to the door there should be a hidden pink (or any color) plastic box which basically controlls the cars security system... i removed it and i was good to go...try that... the only thing though is that you wont be able to lock the doors automaticaly, ull have to do it manually

May 17, 2009 | 1993 Jeep Grand Cherokee

4 Answers

Fuse box


under the drivers side dash by the door

Aug 27, 2008 | 1988 Ford Crown Victoria

1 Answer

Why does my key fob only open drivers door


this how a dealer does it:
DOOR CONTROL TRANSMITTER
REGISTRATION
1. REGISTRATION OF RECOGNITION CODE
HINT:
 The add mode is used to retain the already registered codes while registering a new recognition code.
This mode is used when adding a transmitter. If the number of the registered codes exceeds 4, the previously
registered code will be correspondingly erased in order, starting from the first registered code.
 The rewrite mode is used to erase all the previously registered codes and register only new recognition
codes. This mode is used when exchanging the transmitter or the door control receiver for new one.
 The prohibition mode is used to erase all the registered codes and cancel the wireless door lock function.
Use this mode when the transmitter is lost.
 The confirmation mode is to confirm how many recognition codes have already been registered before
an additional registration of a recognition code.
 All the following registration procedures must be performed in order continuously.
(a) The vehicle should be in the following conditions.
(1) The key is not inserted in the ignition key cylinder.
(2) Driver’s door is OPENED. (The other doors are CLOSED)
(3) Driver’s door is UNLOCKED.
(b) Perform the following operations to select the desired mode.
(1) Insert and remove the key from the ignition switch twice within 5 seconds.
(2) After the above operations, close and open the driver door twice within 40 seconds. Then insert the
key into the ignition key cylinder and remove it.
(3) After the above operations, close and open the driver door twice within 40 seconds. Then insert the
key into the ignition key cylinder and close the door.
(4) Turn the ignition switch from LOCK to ON and back to LOCK at approximately 1 second interval 1
to 5 times to select a mode.(2 times for rewrite mode) Then remove the key from the ignition key cylinder.
(5) After selecting a mode, the integration relay automatically performs the power door
LOCK-UNLOCK operation within 3 seconds to inform the selected mode.
(c) Register the new recognition codes :
(1) Within 40 seconds after the add mode or the rewrite mode has been selected, press the LOCK and
UNLOCK switches on the transmitter switch simultaneously for 1.0 - 1.5 seconds.
Within 3 seconds after the previous operation, press either one of the switches for more than 1.0
seconds.
(2) Within 3 seconds after the transmitter switch has been turned OFF, the LOCK-UNLOCK operation
will be automatically performed once if the registration of the recognition code of the transmitter is
completed correctly. In case the LOCK-UNLOCK operation is performed twice, the registration of
recognition code has failed. Perform the registration procedure from the beginning once again.
(3) If the multiple transmitter to be registered, repeat step (c) within 40 seconds after the previous registration.
this is why the dealer charges for this

Jun 19, 2008 | 2003 Mini Cooper

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...