Question about 1995 Eagle Talon

1 Answer

Waterpump i am trying to change a water pump on the non turbo. the bolts are too long to get out of the bracket that is attached to the motor for the motor mount! which is preventing me to get it out along with the front timing beltcover. do you have any ideas?

Posted by on

  • shady10 Jul 02, 2008

    thats nice to know but that is if the engine is mounted inline with vehicle, that would work but this is transverse mounted!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,010 Answers

Disconnect battery, drain the radiator of coolant, move it out of the way, then remove the fan shroud that has a top section and a bottom section, once you have that out of the way, remove the upper and lower radiator hoses, the heater hoses that connect to the water pump too, now remove the fan from the water pump
you might have either ac, alternator or power steering in the way, and have other bolts. but basically after you have all the rest of the engine removed it is easy to get the water pump off. clean all new surface area's where gaskets touch , use indian head gasket sealer, its the best kind, when you put the new water pump on the engine make sure all the old gaskets are removed and wire brush the water pump housing, use gasket sealer, let it dry ,then put all the hoses back on, the power steering, alternator etc, all back in place, fill up the radiator, let it get to 190% temp, and make sure the thermostat opens, then you know everythings working,

Posted on Jul 01, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a water pump


First drain the coolant if possible (you will find a drain **** on the bottom drivers side of rad). Loosen the water pump pulley bolts while serpentine belt still attached (10mm X 4). Remove the serpentine belt, and plastic diagram bracket just above the waterpump. Remove the (8mm bolts X 5) holding the water pump to front engine housing. Note the little arrow or triangle at the top of waterpump when removing, it will help you to install new water pump in same location. Scrape off most of the old gasket material, use fine sand paper to clean engine surface as best as possible. Install new gasket to water pump, and align the holes (it only goes on one way, and maybe upside down if they don't line up). Locate arrow and reinstall, torque 5 bolts to 89 in/lbs tight but not too tight. Reinstall pulley, serpentine belt and bracket. Tighten the pulley bolts, refill coolant (close drain ****). Just above the waterpump there is a coolant hose with a little 7mm screw for a bleeder. Open the bleeder (engine off). Continue to fill rad with coolant until it comes out bleeder. Close bleeder and test run. Recheck the coolant level later when cooled.

Jan 26, 2011 | 1999 Chevrolet Venture

1 Answer

I need to change the crankshaft sensor switch, what are the steps for this procedure?


Hi, Please follow below steps :


-. Jack up front wheel and remove the tires
-. Remove the Motor Mount next to the Power Steering Pump and timing belt cover

-. Loosen the Alternator/Water Pump belt.
-. Loosen the Power Steering/AC/Tensioner belt by loosening the Tensioner Bolt first.

-. Remove the power steering pump bracket. Leave the pump attached to the bracket.
-. Remove the Water Pump Pulley.

-. Now it's time to remove the Crank Pulley.

-. Remove the Timing Cover bolts.

-. Remove and replace the crankshaft sensor

Jan 12, 2011 | 2004 Kia Optima

3 Answers

How do you replace water pump?


Assuming this is a 460 Ford Big Block:

REMOVAL

-Drain cooling system.
-Remove drive belts.
-Remove bolts attaching fan shroud to radiator.
-Remove fan blade from fan clutch and remove fan shroud.
-Remove fan clutch and water pump pulley from water pump.
-Remove four bolts and one nut attaching A/C compressor mounting bracket to cylinder head and water pump. Do not remove A/C compressor or power steering pump from A/C compressor mounting bracket.
-Pull A/C compressor mounting bracket forward to remove from stud on water pump.
-Remove bolt attaching generator adjusting arm to water pump. Remove four bolts attaching generator mounting bracket to cylinder head, cylinder block and water pump.
-Remove remaining water pump attaching bolts and remove water pump from engine front cover.
-Remove water pump cover from water pump. Discard water pump housing gasket and water pump cover gasket.
INSTALLATION
-Remove any gasket material from water pump cylinder front cover and separator plate mating surfaces.
-Position new water pump housing gasket and water pump cover gasket coated on both sides with Perfect Seal Sealing Compound B5A-19554-A or equivalent water-resistant sealer meeting Ford specification ESE-M4G115-A.
-Position water pump and water pump cover onto engine front cover. Install bolts and tighten to16-24 Nm (12-18 ft. lbs.).
-Install generator mounting bracket to cylinder head, cylinder block and water pump with four attaching bolts. Install generator adjusting arm to water pump with one attaching bolt. Tighten 7/16-inch bolts to 54-71 Nm (40-53 ft. lbs.) and 3/8-inch bolts to 41-54 Nm (30-40 ft. lbs.).
-Position A/C compressor mounting bracket over water pump stud and secure to cylinder head with four bolts tightened to 54-71 Nm (40-53 ft. lbs.) and secure nut to water pump to 41-54 Nm (30-40 ft. lbs.).
-Install water pump pulley and fan clutch to water pump hub with four bolts. Install fan blade to fan clutch with four bolts. Tighten water pump pulley, fan clutch hub bolts, and fan-to-fan clutch hub bolts to 16-24 Nm (12-18 ft. lbs.). Install fan shroud.
-Install drive belts.
-Fill and bleed the cooling system.
-Start the engine and check for leaks

Jan 10, 2011 | 1997 Ford F350 Crew Cab

1 Answer

Were changing the water pump on a 1993 buick lesabre but have run into a problem. Can't get the motor mount out so we can get to the water pump. Have removed 2 bolts and a nut on the engine and all the...


Water Pump REMOVAL & INSTALLATION CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old. 1987-95 Vehicles EXCEPT 1995 VIN 1 ENGINE
  1. Disconnect the negative battery cable.
  2. Drain cooling system into a suitable container.
  3. Remove the serpentine drive belt, as outlined in Section 1 of this manual. NOTE: On some engines, removing the alternator provides better clearance for removing the water pump. For alternator removal and installation procedures, please refer to Section 2 of this manual. Fig. 1: After removing the alternator, remove the brace 89633p01.jpg

  4. Unfasten the water pump pulley bolts, (long bolt removed through access hole provided in the body side rail), then remove the pulley. Fig. 2: Pull the water pump pulley from the pump 89633p03.jpg

  5. Disconnect the radiator and heater hoses from water pump. Fig. 3: Use a screwdriver to loosen the hose clamp screws, then disconnect the hoses from the water pump 89633p02.jpg

  6. For 1992-95 vehicles, remove the torque axis mount, as follows:
    1. Use a suitable engine support fixture and lifting bracket to raise the engine slightly to take the weight off of the engine mounts.
    2. Remove the through-bolt from the torque axis (front) engine mount.
    3. Lift the engine with the support fixture until the power steering reservoir touches the strut tower cross brace.
    4. Loosen the bottom two bolts on the torque axis (front) engine mount.
    5. Remove the A/C line clip and top two bolts on the torque axis engine mount, then remove the mount.
    6. Remove the 2 bolts and nut attaching the engine torque axis mount bracket assembly to the front of the engine. NOTE: On some engines, when you remove the 13mm bolts, coolant will flow from the bolt holes, so make sure to position a drain pan under the pump before unfastening the bolts.
  7. Remove the water pump attaching bolts, then remove the water pump from the vehicle. Remove and discard the gasket. Thoroughly clean the gasket mating surfaces. Fig. 4: Unfasten the water pump mounting bolts (see arrows for locations of top bolts) . . . 89633p04.jpg
    Fig. 5: . . . then remove the water pump from the engine 89633p05.jpg
    Fig. 6: Use a gasket scraper to carefully clean the water pump's mating surface 89633p06.jpg
    Fig. 7: You can also use Scotchbrite® or equivalent non-abrasive scouring pad to clean the water pump gasket mating surface 89633p07.jpg
    Fig. 8: When using a scraper to clean the gasket mating surfaces, be careful not to gouge the engine and cause leaks 89633p10.jpg
    Fig. 9: Exploded view of the water pump mounting - 1994 vehicle shown, others similar 89633g37.gif
    To install:
  8. Apply a suitable sealant to the bolt threads. Fig. 10: Coat the bolt threads with a suitable sealing compound 89633p09.jpg

  9. Position a new gasket, then install the water pump to the engine and tighten the retaining bolts, as follows: Fig. 11: Place a new gasket on the water pump mounting surface 89633p08.jpg
    1. For 1987-94 vehicles, tighten the long bolts to 29 ft. lbs. (39 Nm) and the short bolts to 97 inch lbs. (11 Nm).
    2. For 1995 vehicles, tighten the water pump-to-block bolts to 22 ft. lbs. (30 Nm) and the water pump-to-front cover bolts to 11 ft. lbs. (15 Nm), plus an additional 80°rotation.
  10. For 1992-95 vehicles, install the torque axis mount, as follows:
    1. Attach the torque axis engine mount bracket assembly to the front of the engine using the 2 bolts and nut. Fig. 12: Install the torque axis engine mount bracket and secure with the 2 bolts and nut 89633g34.gif

    2. Replace the 2 upper bolts previously removed from the torque axis engine mount, and attach the mount and plastic clip for the A/C lines.
    3. Tighten the 2 lower bolts that were previously loosened on the torque axis engine mount. Fig. 13: Exploded view of the torque axis engine mount and tightening specifications 89633g35.gif

    4. Adjust the engine height to align the torque mount with the torque axis mount bracket.
    5. Insert the through-bolt, attach the retaining nut and tighten to the specifications shown in the accompanying figure. Remove the engine support and lifting fixture. Fig. 14: Insert the torque axis mount bracket through-bolt 89633g36.gif

  11. Install the water pump pulley and secure with the retaining bolts.
  12. Connect the radiator and heater hoses to the water pump.
  13. Install the serpentine drive belt.
  14. Connect the negative battery cable.
  15. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Check for leaks and top-off the coolant.

Dec 17, 2010 | Buick LeSabre Cars & Trucks

1 Answer

How do i replace a water pump on a 1993 geo


1 disconnect battery ground cable
2 drain cooling system
3 on models with a/c, proceed as follows:

a discharge a/c system
b loosen upper and lower compressor bolts and remove compressor drive belt
c remove a/c line from top of radiator shroud

4 remove water pump drive belt
5 remove reservoir tank from radiator bracket
6 remove radiator shroud and fan/clutch from vehicle
7 remove waterpump pulley from waterpump
8 remove timing tensioner and timing belt
9 remove dipstick tube
10 remove alternator mounting bracket at water pump
11 remove water pump mounting bolts and water pump
12 reverse procedure to install, using new gasket and rubber seal

Feb 18, 2010 | 1993 Geo Tracker

1 Answer

I need step by step instructions on removing and installing a water pump for a 318 Dodge motor... need torque specs also.


1. Drain Coolant 2. Take fan clutch off 3. Take fan shroud off 4. Take the serp. belt 5. Take the brace on the A/C and Alt. bracket 6. Take the A/C compressor off the bracket (but do not recover freon) 7. Take the idler pulley off 8. Take the bracket off but leave the alt. attached to bracket 9. Pull the wiring off the temp.gauge on the intake by the tstat housing 10. Take the bypass hose clamps off by using a hose clamp pliers. 11. Take the lower radiator hose off 12. Take the bolts out of the waterpump and take the pump off with a little tap with a hammer or pry it off. 13. Clean off old gasket 14. Install in reverse

Oct 06, 2009 | 1999 Dodge Ram

1 Answer

1999 Buick Park Avenue Water Pump Removal


Hi once you have all the bolts off for the mount raise the front of the motor up till you can remove the center part of the mount
I use a floor jack and a 2x4 across the oil pan then remove the studs for the motor mount bracket now remove the bracket and now you can get the water pump out
hope this helps

May 10, 2009 | 1999 Buick Park Avenue

1 Answer

1999 Park Avenue water pump removal


if thats got the 3800 or 3100 in it your taking out the wrong bolts!!!!!!!
your trying too remove the whole housing
you dont need too do that !!!
take off the 4- 10 mm bolts on the waterpump pully,then remove the bolts behind it i belive that there are 8 of them that takes the pump from the housing!!

May 10, 2009 | 1991 Buick Park Avenue

1 Answer

Water pump r&r on a 95 buick riviera supercharged.


No. Unfortunately for us 3800 owners, GM decided to put a bolt in that hole instead of a stud with a nut on the end. Yes, you are going to have to take off the motor mount along with the idler pulley bracket. Just make sure you don't put a cheap-o part on and you won't have to do it for another 15 years.

Apr 30, 2009 | 1998 Buick Riviera

Not finding what you are looking for?
1995 Eagle Talon Logo

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Stewart Dibbs

Level 2 Expert

267 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...