Question about 1991 Dodge Dynasty

2 Answers

91 dodge dynasty blower motor

I went to replace the blower motor, and once the new one was installed its not working. All fuses were ohmed, even the one under the hood. During a voltage check there is no power coming to the wires for the blower motor, even when the switch is on high with a/c running. What am I missing?

Posted by on

  • miamibrice Oct 12, 2008

    Does a resitor have anthing to do with motor not working??

×

2 Answers

Check the blower motor resistor located behind the windshield washer fluid. just replaced one and it worked.

Posted on Oct 19, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

Trace the two wires by analyzing which power are you missing...

run a wire from the positive of the battery and put the red wire of the volt meter to it and place the black wire of the meter to the black that goes to the motor.

if there is 12 volts, you have a negative terminal to the motor.

if you dont have, then you dont have the negative terminal to the motor.

next transfer the wire from the positive terminal of the battery to the negative terminal of the battery.

now put the bllack wire of the meter to the wire and test the red /or blue wire that goes to the motor.

it should have a reading of 12 volts.

if there is no reading , then there is no positive 12 volt present on the blue/red wire.

from these test, you can know which wire does not have the power.

that is what you are missing..

tnx 4 using fixya,

cheers,

drcool


p.s.

you could have just missed the black wire to be screwed on the housing of the blower motor.

Posted on Aug 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 DODGE caravan a/c blower fan inop have replaced reistor and control head rear fan works have checked all relays and fuses


Hi Jim, I will try my best to help you. First off, let see what we are losing at the blower motor. Three things I want you to do. #1-With a multi-meter check the power side at the blower motor connector and see if you have a full 12 volts. #2-With a test light hooked to the battery positive terminal, check the ground side at the blower motor connector to see if you have a good ground, the test light should be good and bright. #3-With the multi-meter set on ohm's check across the actual blower motor connector a resistance reading of up too 7 ohms is OK, but if you have a reading above like 14 to 22 ohms then replace the motor. Hope this helps and have an awesome day Jim!

May 23, 2014 | 2010 Dodge Grand Caravan

1 Answer

Need to replace ac/heater fan resistor I am not sure of the location does anyone know? Thank You


The Blower Motor Resistor is located on the passenger side firewall, not far from your A/C's H-Valve (or expansion valve), going inside of the vehicle. The blower motor resistor has a 4 or 5 way black connector plugged into it and this is the only visible portion of the Resistor you will see. Remove the wiring connector and remove the 2 or 3 screws with an 8 mm or 5/16" socket (8 mm and 5/16" are the same). Once the screws or fasteners are removed, just pull the blower motor resistor out of the firewall and if you look at it, it will have various coils of wire on it, sometimes it will show burnt coils, but you can always check the various coils with an Ohm-meter.

Aside from that, install the new Blower Motor Resistor and Voilà! Your inside Blower Motor should work just fine.

A brief note here, if your fan doesn't work when the fan switch is on High, then it's not the Blower Motor Resistor, but possibly the Blower Motor itself. Should this occur, please get back to me insofar as how to replace the blower motor and why the blower motor's wires have to be twisted...even with the new blower motor fan.

Best of Luck,

"00 Buck"

"Still living on the Right Side of Dirt..."

Jun 05, 2010 | 2001 Dodge Caravan

1 Answer

1993 Dodge Dynasty


the blower motors armature could of gone bad, if any noises were heard before hand it was caused by a worn bearing. it will lock solid if this was the case

Feb 20, 2010 | 1993 Dodge Dynasty

1 Answer

HYow to find and replace blower motor on 1990


on rh side under glove box is motor

Feb 05, 2010 | 1990 Dodge Dynasty

1 Answer

I get noheat except a little defrost what could


YOU DIDN'T MENTION IF THE BLOWER WAS WORKING, I'M ASSUMING IT'S NOT, CHECK THE BLOWER MOTOR OR RESISTER, I'D REPLACE BOTH

Nov 14, 2009 | 1990 Dodge Dynasty

3 Answers

Serpentine belt diagram for a 3,3l dodge dynasty with ac


For the 1991 DODGE DYNASTY - V6 3.3L 201ci GAS FI N R , review this informacion:

Belt Routing Diagram
- Multiple Accessory, w/o A.C. (Mfg. After 2/27/91)
- Multiple Accessory, w/A.C. (Mfg. After 2/27/91)
- Multiple Accessory, w/o A.C. (Mfg. Before 2/27/91)
- Multiple Accessory, w/A.C. (Mfg. Before 2/27/91)
684ce70.jpg


Remove the serpentine belt by using a breakover bar, rachet or serpentine belt removal tool with the correct size socket for the pulley mounting bolt. Rotate tensioner arm to release tension. Remove the belt.

Hope helped with this (remember rated this help) Good luck.

Nov 12, 2009 | 1991 Dodge Dynasty

1 Answer

The heater/a/c air or blower does not work. I check the fuse and is ok. How can I change or fix the problem


The blower motor has a resistor. This is with the resistance coils that give you the various speeds of the blower motor. These resistors go out fairly often. On my 99 dodge it is located in the cabin, under the dash, just above where the carpet ends and on the vent/heater housing, It is about just less than an inch and 2 to 3 inches long. Held in by two screws. About a 7 mm size. Should be an electrical connector. Take care not to break the locking tab. These go out, when a motor gets older or gets dirty, or any reason that there might be more drag on the motor. I once fixed a bad resistor by soldering a fuse in line. After replacing a couple of the resistors. A volt ohm meter, would show an open, no circuit, when tested across the resistor. Ohm setting. This would tell you it's bad. LB

Jul 18, 2009 | 1993 Chrysler New Yorker

2 Answers

I HAVE A 1990 DODGE DYNASTY.HOW DO I FIX THE HEATER BLOWER THAT STOPPED WORKING?


it could be a 7 dollar resistor thats bad. Thats located behind the fluid washer resovoir.

Oct 08, 2008 | 1993 Dodge Dynasty

1 Answer

Blower motor


Blower motor is located under the passenger side of the dash behind the glove compartment.

Jun 14, 2008 | 1990 Dodge Dynasty

Not finding what you are looking for?
1991 Dodge Dynasty Logo

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...