Question about 1994 Honda Civic

1 Answer

Inserting new antennia

Can not get the wire to the bottom of car can not locate where it comes out at

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 43 Answers

What kind of a car is it? civic or del sol?
the antenna wire usually runs through the top of your car through the driver metal divider between the front windshield and the drivers door, (i hope you understand that explaination. then it runs through your dash to your radio. if you already yanked the former antenna what i would do is run a long beaded metal rope down your antenna hole and on the other side with a long slender magnet fish it out.

good luck.

Posted on Oct 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace windshield washer pump on 1996 cherokee 1996 xj


washer bottle pump will be located at the bottom end of washer bottle tank,disconnect water hose and electrical connector .
gently twist and wiggle out.
To re install insert new seal in bottle apply some lub and push into washer bottle .
reconnect hose wire electrical terminal .
all should be good now..

Mar 23, 2015 | Cars & Trucks

Tip

How to Replace the O2 Sensor in Mercury villager?


O2 sensor needs to be replaced when you get low gas mileage in car.
The procedure to replace is as follows: ----
1) There is primary and secondary O2 sensor connector.
2) Do the replacement of the O2 sensor only when the engine is completely cool.
3)You will see primary O2 sensor on the exhaust manifold.The secondary O2 sensor is located after the catalytic converter.
4)Put the car on jack stands on the rack, this will give you proper sensor location in the car.
5)Remove the O2 sensor with a socket wrench and O2 removal tool extension. Turn the O2 sensor counterclockwise to remove.
6) Most of the times the O2 sensor comes out very easily but if its bit hard to remove it then you can use "FREEZE spray" to make it gets loose.
7)The spray will make it come out easily.
8)When the O2 sensor is getting removed, some of the wiring's will also come out.
9)Before removing the O2 sensor, take the note of the wiring's and the position of wiring so while inserting new O2 sensor you don't get confused.
10) Now after you remove the old faulty O2 sensor out. Carefully insert new O2 sensor in same position.
11) And reverse/refit all the wires / parts which you removed while replacing the old O2 sensor.
This will help. Thanks.

on Mar 22, 2010 | Mercury Villager Cars & Trucks

Tip

How to Replace the O2 Sensor in a Buick Century Car?


O2 sensor needs to be replaced when you get low gas mileage in car.
The procedure to replace is as follows: ----
1) The oxygen sensor is located under the car.
2) Put the car on jack stands on the rack, this will give you proper sensor location in the car.
3) The sensor has to be turned a bit then it can be easily removed.
4) Most of the times the O2 sensor comes out very easily but if its bit hard to remove it then you can use "FREEZE spray" to make it gets loose.
5) The spray will make it come out easily.
6) When the O2 sensor is getting removed, some of the wiring's will also come out.
7) Before removing the O2 sensor, take the note of the wiring's and the position of wiring so while inserting new O2 sensor you don't get confused.
8) Now after you remove the old faulty O2 sensor out. Carefully insert new O2 sensor in same position.
9) And reverse/refit all the wires / parts which you removed while replacing the old O2 sensor.
This will help. Thanks.

on Mar 22, 2010 | Buick Century Cars & Trucks

1 Answer

Ever so often, my 98 S10 will simply not start. It will start 97 times out of 100. Someone said it was probably the clutch starter safety switch. Well, I bought one, but am not sure how to install it.


The clutch switch is located near the clutch pedal. Depress the locking prongs and it should come right out. Unplug from wiring, plug in new switch, insert new switch in old bracket. Done.

Oct 17, 2013 | 1998 Chevrolet S-10 Pickup

1 Answer

Why is water coming in my car while a/c is on


the drain tube for your evaporator is plugged, and it needs to be cleared-use a stiff, thin and fairly long piece of wire (a coat hanger cut to utilize the straight bottom section works) inserted into the tube from underneath the car is fast and usually a 5 minute or less deal-locate the tube, it is directly in front of the passenger's feet but in the engine compartment, just past the firewall-it usually requires jacking the car up (use jackstands) to have room to see/work on it.

Jun 21, 2011 | Toyota Highlander Cars & Trucks

Tip

How to Replace the O2 Sensor in a Audi All road Car?


O2 sensor needs to be replaced when you get low gas mileage in car.
The procedure to replace is as follows: ----
1) The oxygen sensor is located under the car.
2) Put the car on jack stands on the rack, this will give you proper sensor location in the car.
3) The sensor has to be turned a bit then it can be easily removed.
4) Most of the times the O2 sensor comes out very easily but if its bit hard to remove it then you can use "FREEZE spray" to make it gets loose.
5) The spray will make it come out easily.
6) When the O2 sensor is getting removed, some of the wiring's will also come out.
7) Before removing the O2 sensor, take the note of the wiring's and the position of wiring so while inserting new O2 sensor you don't get confused.
8) Now after you remove the old faulty O2 sensor out. Carefully insert new O2 sensor in same position.
9) And reverse/refit all the wires / parts which you removed while replacing the old O2 sensor.
This will help. Thanks.

on Mar 22, 2010 | Audi AllRoad Cars & Trucks

Tip

How to Replace the O2 Sensor in a Chevrolet Cavalier Car?


O2 sensor needs to be replaced when you get low gas mileage in car.
The procedure to replace is as follows: ----
1) The oxygen sensor is located under the car.
2) Put the car on jack stands on the rack, this will give you proper sensor location in the car.
3) The sensor has to be turned a bit then it can be easily removed.
4) Most of the times the O2 sensor comes out very easily but if its bit hard to remove it then you can use "FREEZE spray" to make it gets loose.
5) The spray will make it come out easily.
6) When the O2 sensor is getting removed, some of the wiring's will also come out.
7) Before removing the O2 sensor, take the note of the wiring's and the position of wiring so while inserting new O2 sensor you don't get confused.
8) Now after you remove the old faulty O2 sensor out. Carefully insert new O2 sensor in same position.
9) And reverse/refit all the wires / parts which you removed while replacing the old O2 sensor.
This will help. Thanks.

on Mar 22, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

I need to replace the windshield washer pump. i think it is located near the bottom of the washer fluid tank. i cannot see it from the top. can anyone tell me what i have to remove to get to it?


pull the washer reservoir out. the black insert in the bottom which has a tube and two wires coming out of it is the pump. a dealer parts guy can tell you if it can be replaced. if so get a new pump at a patrs store, they are all pretty much the same.

Dec 15, 2010 | 2006 Chevrolet Suburban

1 Answer

Where is the windshield washer pump located on the Kia Sephia 2000? Is it only accessible from underneath the car? Thank you.


You know i have a Hyundai and they are made by the same company as KIA. I also have a Subaru, and have had many many different cars over the years. I can not say for sure on a KIA but the washer pump is always in the bottom of the reservoir where you add the fluid. So find the bottom of the reservoir, where you see the hose and wires coming out of a black disc inserted into the side of the reservoir, that is the end of the pump.

Aug 06, 2010 | 2000 Kia Sephia

2 Answers

How do you change headlight bulb in a 1998 suzuki x90?


Behind the headlight assembly is a large weather boot. Grasp the small portion that the wires come into and pull it straight out to remove the wiring harness. Grasp the large weather boot from the bottom and pull it up. Work your way around the rim and remove it. Yank it off the headlight bulb.

You should then see the headlight bulb and a large wire holding it in place. At the bottom of the assembly is a clasp that holds the wire in place. Work the wire out of the clasp and pull it all the way up.
The headlight should now be free and able to be removed. Remove it and replace it with a new one. Align the three tabs of the bulb accordingly; you'll see two of the slots for these tabs at the bottom, the third is at the top. Make sure that the bulb is inserted completely underneath the wire hold-down. This hold-down is required to keep the bulb from moving around. Ensure that you do not touch the bulb with your bare fingers.

With the bulb inserted, push the wire hold-down down into place and lock it into the clasp. Push the large weather boot back on, taking note of the "TOP" label. Push the center portion of this boot around the back of the headlight bulb.
Reinstall the wiring harness and test the light.

Jan 26, 2010 | 1998 Suzuki X-90

Not finding what you are looking for?
1994 Honda Civic Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...