Brakes go to the floor, no brake fluid - 2004 Dodge Stratus

The rear brakes could need adjusted or replaced.. Also the master cylinder could have blown a seal.

check the backside off all wheels.you problably have a leak.

catastrophic failure , DO NOT DRIVE
so find leak, see leak location, that is BAD.
MC (master cylinder)
or slaves (calipers or drum cylinders.
or hoses. (any)
pipes, (aka, hard lines)
junctions.
aBS?

why not post source of leak, or better photos.
or better yet, call a mech. for help .

floor, floor of cab, floor of garage, just a tiny hint on floor
and what 4 corners of car. inside or outside.
,fluid can leak down both sides of any MC

You need to add BRAKE fluid. After that, blead your brakes. You need to find out where the brake fluid went. If there are no leaks, you need to check the remaining life on all four brake sets. If you have no leaks, chances are pretty good that you need new brakes.

ck the brake fluid level. if its out, then fill it up, pump the pedal and find the leak.

For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.

1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

The brake lines still have air in them that is why you are getting very little fluid out. Pump the brakes until they are stiff then open the bleeder screw on the caliper once the pedal goes to the floor close the screw and repeat the process until you get a solid flow of fluid. Start at one wheel and work your way around until all four wheels do this. As you are releasing fluid remember to check your master cylinder and to keep the fluid level right in it since you are releasing fluid through the bleeder screw, if fluid gets low in the master cylinder you will have to start all over again.

usually an indicator of either a loss of pressure due to low fluid and/or air in the system (brake fluid leak) or extremely worn rear brakes (if drum brakes in rear). possible causes include master cylinder (internal fluid pressure leak), external fluid leaks (calipers, lines, wheel cylinders), rear drum brakes extremely worn down or severely out of adjustment. normally worn disc brakes may reduce pedal height SOME, but seldom "to floor". but the "mushy" quote combined with the "floor" quote suggests a hydrolic fluid pressure problem.

bad power booster

When you fixed the brakes, did you take the lid off the master cylinder. I just wonder if you spilled out your brake fluid. The only reason the pedal should go to the floor is if the brake fluid is gone or the master cylinder is not working. Check the fuse. Check the brake fluid level. The pedal only goes to the floor if there is no back pressure in the lines between the master cylinder the lines to the brake pistion on the calipers. Please give me a good ratin and keep me informed.