Replace a rear view mirror - 1997 Chevrolet Lumina

question edited for clarity.
Question moved to sub category.

Check out the link

https://www.google.com/search?q=2018+Infiniti+QX30+replace+the+rear+view+mirror

..

if rear view mirror base plate fell off with the rear view mirror. you can go to auto parts store buy rear view mirror repair kit.

Most cars have the rear-view mirror and the little metal mount that it slides into. If the whole thing has fell off it is an easy fix.
Go to an auto parts place and tell the counter person you need the glue to glue your mirror mount to the windshield. They will know what to give you.
Then you clean the spot the mirror was hung with alcohol. Let dry
Then follow package directions. Basically you do a dab of glue on mount and press to windshield and hold for a bit of time. Then you wait like 12-24 hrs before sliding the mirror onto the mount.

On the other hand if you are asking for a new mirror you can get one from the Buick dealership - parts dept. or a junkyard or just attach any kind of rear-view mirror. Sorry I can't help you if you have a wired mirror.

glass and motor availbable separately

Removal
NOTE: Do not remove the mirror assembly when repairing the individual mirror part. Individual mirror parts can be installed without removing the mirror assembly.

1. Remove the front door trim panel; refer to Section 501-05.

1. Remove the outside rear view mirror access water shield.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect and remove the speaker.

1. Disconnect the outside rear view mirror electrical connector.

1. Remove the outside rear view mirror.
   1. Remove the nuts.
   1. Remove the outside rear view mirror.
      • Feed the outside rear view mirror wiring through the opening in the front door.

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

is it just the glass that broke?

Exterior Mirror Glass Removal

1. Position the inner edge or the exterior rear view mirror glass to its maximum travel.

1. WARNING: Place a shop towel between the exterior rear view mirror glass and the hand to avoid personal injury in the instance of glass breakage.
   Grasp the outboard edge of the exterior rear view mirror glass and pull outward.

1. Remove the exterior rear view mirror glass.
   • If equipped, disconnect the heated rear view mirror glass electrical connectors.

Installation

1. If equipped, connect the heated rear view mirror glass electrical connectors.

1. NOTE: An audible click will be heard during installation.
   Press firmly in the center of the exterior rear view mirror glass until it snaps onto the exterior rear view mirror motor.

go to auto parts store and get a tube of rear mirror adhesive, which is two part adhesive. must follow the direction on the package.

SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal

1. Remove the front door trim panel. For additional information, refer to Section 501-05 .

1. Remove the upper speaker.
   1. Disconnect the electrical connector.
   1. Remove the bolts.
   1. Remove the speaker.

1. Position the watershield aside.

1. Remove the exterior rear view mirror access panel.

1. Disconnect the exterior rear view mirror electrical connectors.
   • Release the wiring harness locator.

1. Remove the exterior rear view mirror.
   • Remove the bolts.
   • Feed the wiring harness through the door opening.

YOU HAVE 2 TAKE OFF THE DOOR PANEL AND TRACE THE WIRE 2 THE PLUG