Question about 2003 Toyota Camry

1 Answer

Rear seat bottom removal

How to remove

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

One of two ways. There may be two tabs at the bottom front of the seat bottom. Pull those out toward the front of the car, and then firmly pull up on the front of the seat bottom. Or, if there are no tabs, then just pull up very firmly on the front of the seat bottom.

Posted on Jul 14, 2008

6 Suggested Answers

polarcycle
  • 1392 Answers

SOURCE: 2005 Jeep Grand Cherokee rear seat removal

For the seat bottom, you just need to pull it up. The seat backs would have to be unbolted.

Posted on Mar 06, 2009

motor1258
  • 6674 Answers

SOURCE: how to remove rear seat from 2001 Audi allroad

Not 100% sure on yours but normally you'll either have a couple of bolts way down under seat cushion at front, near floor, or in some cases, you have to push seat cushion back toward rear window, hard & lift, to pop it out of notched catch under it.

Posted on Mar 14, 2009

smartr10U
  • 1305 Answers

SOURCE: remove rear seat impala2007

To remove the rear seat, pull up on the front of the seat bottom, it should be hooked in place by spring type clips. After you get the front edge up, pull out the seat. This should expose the bolts/screws that hold the seat back in. Look below and there should be a couple of screws holding the seatback to the car body. Remove these and then you can pull the seat back out of the car.
K

Posted on Aug 29, 2009

  • 185 Answers

SOURCE: how to remove rear struts from a avalon toyota

yes you will have to remove the rear seat. the bottom of the seat pulls straight up and out. the back of the seat has twelve mm bolts holding it at the bottom. once those are removed you lift straight up and out, its hooked at top.

Posted on Oct 15, 2009

  • 185 Answers

SOURCE: remove rear seat lexus es300 2008

the bottom of the rear seat pulls straight up at the front and out. its pretty tight, you need to pull very firmly.

Posted on Oct 20, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the back seat to get to the fuel pump?


On what? 3 possible ways the rear seat cushion is removed. On some the seat has clips that lift straight up. Or some have 2 small bolts at front bottom of rear cushion. Remove the bolts and seat slides out easily. The final way is old style: a heavy wire on bottom of cushion, one on each side, fits into slots that come up from the frame underneath. To remove, push cushion hard to the rear until the heavy wires can be removed (lifted up) from the slots. Do one side at a time. These are the most difficult to remove the rear bottom cushion. You have to push hard against the cushion near the bottom of it, pushing it backwards, so the wire comes out of the slot, and then cushion can be removed.

First try lifting straight up on the cushion. Since there is an access panel to the gas tank, it is very possible the cushion is easily removed by lifting straight up.

Jun 05, 2015 | Seat Cars & Trucks

1 Answer

Remove rear seat in a towncar


The rear seat bottom cushion is attached with hooks,no tools should be needed to remove the seat bottom.lift slightly up on the cushion with one hand,and use the other hand to "thump" the front of the cushion towards the back of the car.(one hook on each side,thump the seat about 12" from the side)

Jan 02, 2012 | Austin-Healey 3000 Cars & Trucks

3 Answers

How to remove back seat in 1972 buick skylark


Remove the seat cushion retaining bolts, detach the seat cushion and remove it up and out from the vehicle.

Remove the rear seat back retaining bolts at the bottom of the seat back. Pull up then out to disengage the upper frame from the hangers and remove seat back from the vehicle.

Installation is the reverse of removal.

Courtesy: Haynes GM repair Manual #38025. You can probably find a copy of it on Amazon or eBay cheap

Jun 20, 2011 | Buick Skylark Cars & Trucks

1 Answer

How to remove bottom of back seat need to remove seat to remove rear shocks..


PUSH IN CENTER FRONT EDGE CUSHION TO DISENGAGE PART OF SEATS WIRE FRAME FROM CLIPS.WITH CLIPS UNHOOKED LIFT UP AND REMOVE SEAT.IF REAR SEAT NOT HELD IN PLACE WITH CLIPS. LIFT UP THE REAR SEAT CUSHION AND PIVOT IT FORWARD. DETACH THE RETAINING BOLTS AT THE LOWER EDGE OF THE SEAT BACK AND IF NECESSARY REMOVE THE SEAT BELT ANCHOR BOLTS.LIFT UP ON SEAT BACK REMOVE IT..

Feb 06, 2011 | Jaguar X-Type Cars & Trucks

1 Answer

Truck lock is jammed by briefcase strap. can i get into the trunk from the back seat? such as does the back seat fold down?


I searched the owner's manual and there was no mention of folding the rear seats down. If you don't have a manual, you can get one here: http://www.extendedgmwarranty.com/owners-manual/buick/1999-Buick-Century.pdf

You can remove the seats following the instructions below from autozone.com.
Rear Seats
SEAT CUSHION


jturcotte_98.gif

Fig. Typical W-Body rear seat cushion removal

  1. Locate and remove the small bolts at the front lower edge of the seat cushion.
  2. Pull the tabs on the rear cushion retainers.
  3. Remove the seat cushion by lifting up and pulling out of the retainer.
  4. Installation is the reverse of the removal procedure. Make sure the retainer tabs are snapped into place. Tighten the bolts to 18 ft. lbs. (25 Nm).

SEAT BACK


jturcotte_99.gif

Fig. Typical W-Body rear seat back removal

  1. Remove the seat cushion as described above.
  2. Remove the anchor nuts securing the rear seat retainer at the bottom of the seat back.
  3. Grasp the bottom of the seat back and swing upward to disengage the offsets on the upper frame bar from the hangers.
  4. Lift the seat back upwards to remove from the vehicle.
  5. Installation is the reverse of the removal process. Make sure the hooks on the seat back are properly installed to the hangers. Tighten the anchor nuts to 89 inch lbs. (10 Nm).

Nov 07, 2010 | 1999 Buick Century

1 Answer

How to remove rear struts from a avalon toyota 1996 will the rear seat have to be remove or can it be done with out removing the rear seat, can I get instruction on line


yes you will have to remove the rear seat. the bottom of the seat pulls straight up and out. the back of the seat has twelve mm bolts holding it at the bottom. once those are removed you lift straight up and out, its hooked at top.

Oct 15, 2009 | 1996 Toyota Avalon

2 Answers

On a 1989 nissan maxima with sonar suspension II how do you disassemble the strut assembly? the mounting bracket for sonar adapters is in the way of the strut center bolt.


First you must remove the rear seat to gain access to the top strut mounts. The bottom of the rear seat comes out first. On the 91 model there are two tabs at the base of the seat bottm that you pull forward to release the seat bottom. I'm not sure if the 89 is the same. After removal of the rear seat bottom, you will see a bolt at the bottom of each side of the rear seat back that need to be removed. Fold down the arm rest and disconnect the vinyl cover at the base of the armrest to expose and remove two screws. Push up on the rear seat back to unhook three plastic hooks (center and one at each end) at the top of the rear seat back. Remove the seat back. Remove the large metal support panel that is behind the seat back. Safely jack up the rear of the car and support on jack stands so the rear wheels hang free. Doing one strut at a time, remove the two top strut mount bolts leaving the center strut stud nut in place. The strut and mount will lower out of the unibody. Disconnect the bottom strut mount. Remove the strut/coil spring assembly. Using a strut/spring compressor (some auto parts stores rent these) compress the spring. Carefully remove the top strut stud retaining nut, top strut mount, bumpers and strut boot. Carefully install compressed spring, strut boot, bumpers and top strut mount on new strut and install washer and retaining nut. Reinstall strut and etc. in reverse order.

Sep 15, 2009 | 1989 Nissan Maxima

1 Answer

How to remove interior back dash on 2006 hyundai sonata


The shop manual does not illustrate the procedure for removing the rear package deck (back dash). This will be a lengthy description for removing this deck
1. Remove the rear seat bottom (2 12mm bolts located in between the seams at the seat back and the seat bottom (lower the seat backs and you'll have to feel for them). Remove them
2. Remove the seat bottom (two spring loaded clips at the front of the seat bottom).
3. Remove the 12 mm bolts at the bottom of both LH & RH shoulder cushions. Lift UP and then forward (careful you don't break the should cushion clips at the back of the cushions).
4. Using a small screwdriver, remove the SRS caps at the C-Pillar moldings (behind them are either two phillips head screws or 10mm bolts) - remove them
5. Remove the C-Pillar moldings -- they are 'Clipped' into position (use a flashlight to locate them and a long shaft plane screwdriver to help 'unclip' them).

ff32eaf.jpg lower the seat backs down. Note the trunk accessway side moldings (approximately 8 to 10 phillips head screws) remove them and the accessway moldings (you can'r remove the deck unless you remove these accessway moldings).
6. Find the plastic clips which hold the rear deck in place (usually yellow or blue)


0fbe0c6.jpg Remove the rear package deck.
Now, depending on what you want to do now... it's up to you.
Reassembly is in reverse order.

Jun 19, 2009 | 2006 Hyundai Sonata

2 Answers

Help me plz


Please use this link and follow the instructions:

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800bcc6c



Good luck....

Sep 10, 2008 | 1996 Pontiac Grand Am

1 Answer

Honda Accord brake light removal


It's a lot of work for just cleaning.
Fold the rear seat down and remove the two 12mm bolts on the bottom corners of the seat back, pull the seat out.
Between the seat bottom and the carpet you will find two tabs you need to pull and then pull the seat bottom up and out of the car.
Remove the two 10mm bolts securing the seat bolsters to the area the seat bottom was covering. Pull the seat bolsters up and out of the car.
Pop the "C" pillar trim off of the car (above the parcel shelf and beside the rear glass) (side airbag vehicles have a slightly different procedure.)
Pull up on the parcel shelf carefully and evenly. Remove clean and put everything back together.

Aug 16, 2008 | 2005 Honda Accord

Not finding what you are looking for?
2003 Toyota Camry Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...