Question about 1992 Honda Civic

1 Answer

Banjo nut Hi I was curious to know how I could remove a Banjo nut that is ceased. The Banjo nut is attached to my fuel filter.

Posted by on

  • walkjb Jul 16, 2008

    Thanks for the info but I need the banjo nut when when I replace the filter, so cutting it off won't do.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 117 Answers

They are a massive pain in the bum ,the only way is to either cut the head of the bolt off or drill it out

Posted on Jun 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

May have air in the gas line. where to bleed?


There is no good way to do it. It can be done at the banjo connection on the top of the fuel filter. It is found on the drivers side of the engine compartment just below the air filter. Make sure you get a wrench on the top nut just below the banjo connect to hold the fuel filter from turning while removing the banjo bolt. Place a rag over the fitting to keep gas from spraying all over and something to catch the drips. Once loose you can jumper the B+ terminal with the Fp terminal in the diagnostic connector. Then turn the ignition to the on position and the fuel pump will start running with out starting the car. You may need new copper washers to reseal the banjo connection.

Aug 16, 2012 | 1986 Toyota Camry

1 Answer

I need a picture of my motor in my celica gt 2000 so i ca locate my ful filter


Removal & Installation Look for the filter on the side of the fenderwell under the hood, if not on either side look on the firewall mounted with 1 bolt.

Print

CAUTION Observe all applicable safety precautions when working around fuel. Whenever servicing the fuel system, always work in a well ventilated area. Do NOT allow fuel spray or vapors to come in contact with a spark or open flame. Keep a dry chemical fire extinguisher near the work area. Always keep fuel in a container specifically designed for fuel storage; also, always properly seal fuel containers to avoid the possibility of fire or explosion.
There are two types of fittings used on fuel filter connections. The banjo fitting or union bolt type uses a bolt and two washers to prevent leakage between an eyelet and the filter. The flare fitting type uses no washers or bolts. It uses a thread interference pattern to make a tight connection.

  1. Unbolt the retaining screws and remove the protective shield (if equipped) for the fuel filter.
  2. Place a pan under the delivery pipe (large connection) to catch the dripping fuel and SLOWLY loosen the banjo fitting bolt or flare fitting at the bottom of the filter to bleed off the fuel pressure.



0996b43f802224c0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Place a pan under the filter, the remove the lower line


0996b43f802224bf.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the union bolt and two gaskets, then disconnect the inlet hose from the fuel filter

CAUTION To avoid personal injury, remember that the fuel system is under pressure. Release pressure slowly and contain spillage. Wear eye protection and observe no smoking/no open flame precautions. Have a dry powder fire extinguisher within arm's reach at all times.

  1. Remove the banjo bolt or flare fitting and drain the remaining fuel.
  2. Disconnect and plug the inlet line.
  3. Unbolt and carefully remove the fuel filter. It may still contain some fuel.

To install:
When tightening the fuel line bolts to the fuel filter, you must use a torque wrench. The tightening torque is very important, as under or over tightening may cause fuel leakage. Insure that there is sufficient clearance between the fuel filter, lines and any other parts.
  1. Coat the flare or banjo bolt threads along with the copper washers lightly with engine oil. Always use new washers.
  2. Hand tighten the inlet line to the fuel filter.
  3. Install the fuel filter then tighten the banjo type bolt to 22 ft. lbs. (29 Nm) or the flare fitting on the fuel pump side to 17 ft. lbs. (24 Nm) and all others to 22 ft. lbs. (30 Nm).


WARNING The fuel pump builds high pressure within the lines. If new gaskets are NOT used, a high-pressure leak may spray fuel onto the engine or other hot surface.
  1. Run the engine for a few minutes and check for any fuel leaks.
  2. Install the protective shield if removed.



0996b43f802094dd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Always use new gaskets when replacing a fuel filter


0996b43f802094de.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. A line wrench with an extension may be needed to loosen the inlet line at the filter-Corolla

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding Protective shield for the fuel filter If necessary, air cleaner hose and cap If necessary, charcoal canister. Slowly loosen the lower flare nut fitting until all the pressure is relieved Banjo fitting and 2 metal gaskets. Discard the gaskets Fuel line with the flared nut from the filter Filter from the mounting bracket

To install:
  1. Install or connect the following:

    New fuel filter Banjo fitting with a new metal gasket on each side and install the union bolt. Bolt: 22 ft. lbs. (30 Nm). Flare nut to the lower connection. Nut: 22 ft. lbs. (30 Nm). Charcoal canister Air cleaner hose and cap Protective shield Negative battery cable

Aug 02, 2012 | 2000 Toyota Celica

1 Answer

Best way to take it off


Acura Coupes and Sedans 1986-1993 Repair Guide
Fuel Filter

Print
The recommended change interval for the fuel filter on all models is 60,000 miles under normal service. Severe service will require more frequent changing of the fuel filter.
The filter is located in the passengers side of the engine compartment.

CAUTION Before disconnecting any fuel lines, be sure to open the gas tank filler cap to relieve any pressure in the system and wrap a shop towel around the fuel line fitting before opening. Observe all fuel handling precautions.


REMOVAL & INSTALLATION

See Figures 1, 2 and 3

  1. Disconnect the negative battery cable.
  2. Wrap a shop towel around the fittings and using a proper wrench, slowly loosen the fuel line fittings.
  3. Remove the 2 banjo bolts from the fuel lines.
  4. Remove the fuel filter clamp retaining bolt and the clamp.
  5. Remove the filter from the vehicle.

It is very important that ALL of the fuel line banjo bolt washers be replaced every time the banjo bolts are loosened. If the washers are not replaced the fuel lines will leak pressurized fuel causing the risk of fire or explosion.
  1. Install the new filter in position and tighten the clamp mounting bolt to 7 ft. lbs. (10 Nm).
  2. Attach the banjo fittings with new washers in place. On Legend and Vigor, tighten the fuel line flare connector to 28 ft. lbs. (38 Nm). On the remaining models, tighten the banjo fitting bolts to 20 ft. lbs. (27 Nm).
  3. Start the vehicle and check for leaks.



0900c152800494d0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Disconnecting the fuel lines from the fuel filter


0900c152800494d1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Fuel filter replacement-1991-93 Integra


0900c152800494d2.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Fuel filter replacement-Legend and Vigor

Jul 08, 2012 | 1991 Acura Legend

1 Answer

Where is the schrader valve


I assume you are looking for the test port for the fuel system?

If so you will not find a schrader valve. You will need a banjo style test fitting that will replace the banjo bolt that holds the fuel line to either the fuel filter or the fuel rail. you will then be able to attach a pressure gauge to the fitting and check fuel pressure.

Dec 13, 2011 | 1998 Honda Accord

1 Answer

How to replace cabin and fuel filters for 1996 acura 3.2 TL?


For the fuel filter:


Removal & Installation

Many Acura models are equipped with a theft deterrent audio system. Make sure you have the necessary code before disconnecting the battery.

  1. Disconnect the negative battery cable.
  2. Properly relieve the fuel system pressure, as outlined in Section 5 of this manual.

On 2.2L and 3.0L engines you may have to remove the engine wire harness bracket and power steering feed hose clamp.

  1. Wrap a shop towel around the fittings and, using a proper flare nut wrench, slowly loosen the fuel line fittings.


c17hydro_144.gif
  1. Remove the banjo bolts from the fuel lines.
  2. Remove the fuel filter clamp retaining bolt and the clamp.
  3. Remove the filter from the vehicle.

A through cleaning of the high pressure hoses is recommended before installation.

To install:

  1. Install the new filter and tighten the clamp mounting bolt to 7 ft. lbs. (10 Nm).
  2. Attach the banjo fittings with new washers in place.
  3. Tighten the banjo fitting bolts to 25 ft. lbs. (33 Nm).

On 2.2L and 3.0L engines you may have to reconnect the engine wire harness bracket and power steering feed hose clamp.

  1. Connect the negative battery cable, then start the engine and thoroughly check for leaks.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 35; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Jan 23, 2011 | 1996 Acura TL Series

2 Answers

Can not find fuel filter


On this model the fuel filter is inside the gas tank.

Dec 13, 2009 | Honda CR-V Cars & Trucks

1 Answer

Where is the fuel filter located on 93 sr5 v6 4wd ?


I did this last night and it took me about 3 hours. You will need some 12mm, 14mm, and 17mm wrenches and sockets, and a couple of long extensions for your socket. Disconnect your battery, remove the front passenger tire, and then disconnect your power cable on the starter (12mm nut). Remove the starter (one 14mm bolt on bottom, one 14mm nut on top). You'll probably have to use your extensions to get that top nut off. Then take the banjo nuts off the filter, let it drain a minute, and unbolt it from the engine. Put the new one in, tighten the banjo nuts with a torque wrench to 22lbs, and start reassembling everything. Assembly goes a lot faster than disassembly. Keep in mind that this thing is in the worst possible position, and there is no way for you to reach anything, fit your hand where it needs to go, and is a giant contortion act from beginning to end. I hope the sorry Japanese engineer that came up with this idiotic configuration reads this and commits seppeku, or at least gets some bad fugu

Aug 12, 2009 | 1993 Toyota 4Runner

1 Answer

Where is fuel filter in my 2005 camry


your filter should be visible from under the hood....or from under the nose of the car. will be bolted to the fender well.
0900c15280197a0d.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Always use new gaskets when replacing a fuel filter


0900c15280197a0e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. A line wrench with an extension may be needed to loosen the inlet line at the filter-Corolla
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding Protective shield for the fuel filter If necessary, air cleaner hose and cap If necessary, charcoal canister. Slowly loosen the lower flare nut fitting until all the pressure is relieved Banjo fitting and 2 metal gaskets. Discard the gaskets Fuel line with the flared nut from the filter Filter from the mounting bracket

To install:
  1. Install or connect the following:

    New fuel filter Banjo fitting with a new metal gasket on each side and install the union bolt. Bolt: 22 ft. lbs. (30 Nm). Flare nut to the lower connection. Nut: 22 ft. lbs. (30 Nm). Charcoal canister Air cleaner hose and cap Protective shield Negative battery cable

Jul 10, 2009 | 2000 Toyota Camry

1 Answer

Basic service


Here are detailed instructions on the location, removal, and re-installation of your fuel filter. Hope it helps and have a great day!

REMOVAL & INSTALLATION
Carbureted Engines
These vehicles use two replaceable fuel filters. A small one is in the fuel line under the hood; a larger one is located at the rear, just inboard of the left rear wheel.
Whenever the filter(s) are replaced, take great care to avoid the entry of dirt into the lines. Also, pay attention to the correct installation position. It is possible to install the filter backwards.
FRONT
See Figure 2
  1. If applicable, disengage the filter or hose from its retaining clip.
  2. Using two fuel line clamps, pinch off both fuel lines. Take care not to crush the lines; just clamp them shut.
If the fuel hoses are hard or cracked, it is necessary to replace them.
0900c1528005f267.jpgFig. 2: Front fuel filter used on carbureted engines
  1. Loosen the fuel line clamps and slide them back.
  2. Using a twisting motion, remove the fuel lines from the filter.
  3. To install, use a new fuel filter and reverse the removal procedures. Start the engine and check for leaks. Correct any leaks immediately.
REAR
See Figures 3, 4, 5 and 6
  1. Raise and safely support the rear of the vehicle. Remove the left rear wheel.
  2. Remove the bolts securing the filter and its basket to the fuel tank.
0900c1528005f268.jpgFig. 3: Remove the bolts securing the filter and its basket to the fuel tank ...
  1. Push the fuel filter retaining tab and release it from the basket.
0900c1528005f269.jpgFig. 4: ... then release the basket from the filter
  1. Using two fuel line clamps, pinch off both fuel lines. Take care not to crush the lines; just clamp them shut.
0900c1528005f26a.jpgFig. 5: Clamp the fuel lines shut. If the lines are hard, cracked or brittle, they must be replacedIf the fuel hoses are hard or cracked, it is necessary to replace them.
  1. Loosen the fuel line clamps and slide them back.
  2. Using a twisting motion, pull the fuel lines from the fuel filter; remove the filter.
0900c1528005f26b.jpgFig. 6: After sliding the retaining clamps back, the filter can be removed from the linesTo install:
  1. Use a new filter and reverse the removal procedures.
  2. Make certain the retaining tabs are engaged when the filter is installed in the holder. Tighten the bolts until snug.
  3. Install the left rear wheel. Lower the car to the ground.
  4. Start the engine and check for leaks. Correct any leaks immediately.
Fuel Injected Engines
See Figures 7, 8, 9, 10, 11 and 12
The canister fuel filter is located in the engine compartment. When buying the new filter, also buy new washers for the banjo bolts and the service bolt. Failure to replace these washers invites high-pressure fuel leaks. Replacing the washers is required, not recommended.
  1. Disconnect the negative battery terminal.
  2. The fuel system is under pressure. Release pressure slowly and contain spillage. Observe "no smoking/no open flame" precautions. Have a Class B-C (dry powder) fire extinguisher within arm's reach at all times.
  3. Disconnect the banjo bolts and/or threaded fuel line fitting from the fuel filter. Use of a flare nut or line wrench is recommended for disconnecting and attaching this fitting.
0900c1528005f26c.jpgFig. 7: Fuel filter used on fuel injected Accords through 1989 0900c1528005f26d.jpgFig. 8: Fuel filter on 1990-93 fuel injected Accords 0900c1528005f26e.jpgFig. 9: Fuel filter used on fuel injected Preludes through 1991
  1. Loosen the fuel filter clamp bolt, then remove the filter.
To install:
  1. Install the new filter and secure the clamp bolt.
  2. The upper and lower washers on each banjo bolt and the washer on the service bolt MUST be replaced whenever the bolts are loosened. Install the washers and banjo bolts. Tighten the banjo bolts to 16 ft. lbs. (22 Nm) on all models except 1992-95 Preludes. On these models, tighten the bolt to 20 ft. lbs. (28 Nm). If applicable, tighten the threaded fuel line fitting to 27 ft. lbs. (37 Nm).
0900c1528005f26f.jpgFig. 10: Fuel filter used on 1992-95 Preludes 0900c1528005f270.jpgFig. 11: Fuel filter used on 1994-95 4-cylinder AccordsIt will be necessary to use a crow's foot attachment on a torque wrench to properly tighten the threaded fuel line fitting.
  1. Tighten the service bolt to 9 ft. lbs. (12 Nm).
  2. Start the engine and check for leaks. The engine may crank longer than normal until full fuel pressure is developed. Correct any leaks immediately.
0900c1528005f271.jpgFig. 12: V-6 Accord fuel filter

Nov 23, 2008 | 1985 Honda Accord

Not finding what you are looking for?
1992 Honda Civic Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21984 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...