Question about 1991 Toyota MR2

1 Answer

Light hights my off side front light rides a bit high when switched off.can i adjust this.

Posted by on

  • v1k1ng Oct 29, 2008

    sorry reply is late pc problems.sorted problem.with lights left up there is 4 scews holding a black casing.take it off n look under the light.there is a rubber stopper.its hard to get to but theres an adjuster at the bottom.cheers bud.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

You should be able to, there will be a adjustment knob around the light assembly, it may be hiding under some plastic trim

Posted on Aug 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights dont come on and the Shifter will not come out of PARK?


Most likely the stop light switch is to blame; it's either failed or is very far out of adjustment. This is especially common in Hondas... They're a manufacturer that uses the brake light/ stoplight switch to control the brake lights, shift lock and even cruise control. That's probably your point of failure. The good news is that it's easy to get to and fairly inexpensive, it's located right above the brake pedal pad on the front side of it.

May 05, 2016 | 2006 Nissan Titan

1 Answer

Beam one side replace hight lite works but one low do not


you need a new light bulb. there are two different bulbs for high and low beam or 2 filements in one bulb. ether way you need a new light bulb

Mar 13, 2013 | Cars & Trucks

1 Answer

I need to know how to adjust my headlights eg/ how far back should I be parked and how high up the wall should the beams be for high and low beam


12 METERS THE LOW BEEN SHOULD BE THE HIGHT OF A BUMPER , CONCENTRATED LIGHT SHOULD BE STRAIGHT ON THE LEFT SIDE AND THE RIGHT SIDE A LITTLE BIT TURNING TO THE RIGHT.

Jul 31, 2010 | Toyota Camry Cars & Trucks

1 Answer

Front is low !!


To alter the vehicles ride hight is a drastic and costly solution. The shock adsorbers will not alter the ride hight as it's the strut assy that determines the vehicles hight, Also ensure there are no excessively heavy items in the trunk . A broken exhaust mounting will lower underside clearences. Check and inspect all mountings. It would be worth measuring your kerd side height with a similar vehicle. I presume you don't mean , side skirts added at a later date on vehicle. Good Luck

Apr 11, 2010 | 1999 Mercedes-Benz E-Class

1 Answer

1998 Ford F-150, 6 cylinder, Beverly Hills, CA, December 26, 2009, 16:15 no heater head lights on no dash lights head lights off dash lights air bag light on all the time 4 way flasher lights on all the...


surely this didn't just happen one day. did you mess with the wiring harness or have someone mess with it . you can also check the fuses under the hood . you have some major stuff happening there. good luck

Dec 28, 2009 | 1998 Ford F150 Regular Cab

2 Answers

What is ride level on 1990 cadillac brougham


Ride level is exactly what it says it is. It has an electronic suspension system with air shocks which monitors the ride hight and adjust it as needed due to road conditions or speed, to make the ride quality more comfortable

Oct 17, 2009 | 1990 Cadillac Brougham

2 Answers

I need to know the hight ,,when adjusting the


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 11, 2009 | 2001 Pontiac Grand Prix

1 Answer

2001 ford focus headlights


check the hight beam switch and see if it is broken, when you pull on it to turn on the hight beams it should click if not replace the switch and your problem whould be fixed

May 19, 2009 | 2001 Ford Focus

1 Answer

Lexus is300 headlamp adjustment


Is the car lowered? mine does that too but is has 1.4 inch lowering springs. i readjusted the hight of the lights manually and they work fine now.

Jul 17, 2008 | 2001 Lexus IS 300

Not finding what you are looking for?
1991 Toyota MR2 Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...