Question about Mercedes-Benz E320

1 Answer


Im having promblems tighting the serpatine belt ,ive had to replace it ..I have it in correct position .I cant seem to find where or how to remove the slack..Keith Williamson Thank you ..

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Go to autozone dot com and look around thier site they have the location of the tentioner.

Posted on Jun 27, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Mercedes clk 320 airbag

If the airbag light is on something in the system is broken. Go to AutoZone or similar and have them scan the airbag system for codes. My guess would be a faulty seat sensor or a faulty seat belt sensor

Jun 16, 2017 | 1999 Mercedes-Benz CLK

1 Answer

Serpatine belt mercadise c350 diagram

Serpentine belt routing diagram for Mercedes C 350:
272 HP / 6000 rpm - Engine code: 272.960

CS = Crankshaft
G = Guide pulley
Gen = Alternator
T = Tensioner
AC = Air Conditioning
PAS = Power Assisted Steering
WP = Water Pump

Please rate my response. Thanks!

May 22, 2010 | 2008 Mercedes-Benz Mercedes Benz C Class

1 Answer

Need diagram to replace belt on 95 Mercedes E 320

Hope this helps...not sure of the size of motor you have...or if it is a SOHC or DOHC.


Poly V-belt routing—3.2L engines

Mar 06, 2010 | 1995 Mercedes-Benz E-Class

1 Answer

Replaced the alternator on a 2001 Chevy Metro LSI and now I cannot seem to achieve proper belt tension, the belt squeaks very loudly, I applied belt dressing and tried several settings of tight and loose...

Belt dressing isn't advised for vechiles with serpatine belts. they are ment for the old V style belts. Use brake cleaner, carb cleaner to clean off the belt. Then recheck to see if everything is routed the correct way. Check the pulley on the new altenator. Is it the same size as the old one? If not, repalce with old pulley. These three items are the usual cause of poor tension. The tensionor could be going bad too but that isn't a very likely occurance.

Feb 21, 2010 | Chevrolet Metro Cars & Trucks

1 Answer

I need to know how to put a serpatine belt back on jeep cherakee 95 6cyl

Belt adjustment is done by loosening the bolts holding the poser steering on and screwing in/out the screw under the pump.(head is under the pump facing the left fender) Draw yourself a diagram before removing the belt so you don't have a problem putting it back on.

Jan 19, 2010 | 1995 Jeep Cherokee

1 Answer

My serpatine belt is either loose or too tight, how do I make it stop squeeling?

you have to replace it. There is a tension pully that you take a wrench to and loosen the tension to remove the belt.

Nov 11, 2009 | 2003 Kia Spectra

1 Answer

1999 serpatine belt

Hi,the serpentine belt is tensioned automatically by means of a spring loaded tensioner,this is released by using a long 1/2 inch extension bar which fits into a square hole, once pulled back the tensioner can then be held by a nail etc, which is inserted into a hole which aligns with another hole,thus holding the tensioner back in a pre-loaded position to allow you to replace the belt,once replaced you can then pull back the extension bar to remove the nail again and then slowly let off the tension, IF replacing the tensioner, The new one comes pre-loaded with a pin in location to hold it ,hope this is of some help, Bill.

Feb 20, 2009 | 1999 Saab 9-5

1 Answer

1985 mercedes benz

I took the car to a mechanic and am having him fix it.

Oct 04, 2008 | 1985 Mercedes-Benz 190

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

77499 Answers

Joseph Prosser

Level 3 Expert

772 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides