Question about 1995 Acura Integra Coupe

2 Answers

1995 Integra pulleys

How do i remove the crankshaft pulley i can't get it loose

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

You need an assistant hold a large screwdriver wedged in the ring gear teeth on the fly wheel. than loosen the pulley with a socket and breaker bar.Have to turn counterclock. TRY IT

Posted on Apr 12, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Acura Master
  • 14,036 Answers

You need a chain wrench and a 1/2 inch break bar with a deep socket.

Posted on Apr 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 Eagle Talon Esi 2.0L 4cyl non-turbo. Removing crankshaft pulley in midst of water pump replacement. Haynes Manual diagram shows smaller diameter outer section of pulley (A/C & Power Steering...


i have the same car and did the same thing,,, pop the engine mount off and lower the engine slightly with a jack, it will have just enough clearance to squeeze the pulley out :)

Oct 05, 2010 | 1995 Eagle Talon

1 Answer

Can't get the crank pulley loose. is it left our right threads. i am replacing the water pump.


TURN CRANKSHAFT BOLT COUNTERCLOCKWISE TO LOOSEN. YOU HAVE RIGHT HAND THREADS.ENGINE TURNING CLOCKWISE.YOU NEED A STRAP WRENCH HOLD CRANKSHAFT PULLEY WHILE LOOSEN IT.BUT YOU NEED A CRANKSHAFT DAMPER REMOVAL TOOL.OR HARMONIC BALANCER REMOVAL TOOL.YOU NEED STRAP WRENCH TO HOLD CRANKSHAFT PULLEY WHEN TIGHTEN IT.TORQUE CRANKSHAFT PULLEY BOLT 90 - 98 FT LBS. MAKE JOB EASIER.HAVE A HELPER HOLD STRAP WRENCH WHEN YOU LOOSEN OR TIGHTEN CRANKSHAFT PULLEY.

Sep 19, 2010 | 1995 Mercury Villager

1 Answer

Timing belt removal 94 mercury villager


Hi, Disconnect battery ground cable, then drain coolant. Remove accessory drive belts. Remove A/C compressor drive belt idler pulley (tensioner) bolts, then idler pulley (tensioner). Remove upper radiator hose bracket bolt. Loosen two upper radiator hose clamps, then remove upper hose and bracket. Remove coolant bypass hose between thermostat housing and intake manifold coolant outlet. Disconnect main wiring harness from upper front cover (timing belt) cover, then remove eight upper timing belt cover bolts, then the upper cover, Fig. 20. Raise and support vehicle. Remove right front wheel and tire assembly and splash shield. Use strap wrench tool No. D85L-6000-A, or equivalent, to hold water pump pulley while removing water pump pulley bolts. Remove water pump pulley from water pump. Remove crankshaft pulley. Remove five lower timing belt cover attaching bolts and the cover. Rotate crankshaft in a clockwise direction to align crankshaft and camshaft sprocket timing marks, Fig. 21. If timing belt is to be reused, mark direction of rotation. Loosen timing belt tensioner nut, then remove timing belt. CAUTION: With timing belt removed, avoid turning camshaft or crankshaft. If movement is required, exercise extreme caution to avoid valve damage caused by piston contact.
Take care

Jul 24, 2010 | 1995 Mercury Villager

2 Answers

I am planning to replace the timing belt on my daughter's 95 Corolla and was wondering what I need to align where before removing the belt eg How do I find TDC? Camshaft pulley and Crankshaft pulley...


TDC is top dead center/ remove spark plug on cylinder no. 1/ rotate the crankshaft pulley using a socket wrench and power handle and check if the piston on your cylinder no. 1 reach the top center that is TDC/ remove timing belt cover and locate a synchronized marking on your camshaft and crankshaft pulley/ remove old timing belt/ install a new one but make sure that the mark on your camshaft and crankshaft is perfectly synchronized before putting the cover/ manually rotate the crankshaft pulley again and see if it rotates 360 deg. freely then you can be sure you did the job correctly.

Apr 06, 2010 | 1995 Toyota Corolla

1 Answer

Replace timing belt


1993–96 2.3L and 2.6L Engines
  1. Disconnect the negative battery cable.
  2. Loosen and remove the engine accessory drive belts.
  3. Remove the cooling fan assembly and the water pump pulley.
  4. Drain the fluid from the power steering reservoir.
  5. Unbolt and remove the power steering pump. Unbolt the hydraulic line brackets from the upper timing cover and move the pump out of the work area without disconnecting the hydraulic lines.
  6. Disconnect and remove the starter motor if a flywheel holder (part No. J–38674) is to be used.
  7. Remove the upper timing belt cover.
  8. Rotate the crankshaft to set the engine at TDC/compression for the No. 1 cylinder. The arrow mark on camshaft sprocket aligns with mark on the rear timing cover.
  9. Remove the crankshaft pulley.
  10. Remove the lower timing belt cover.
  11. Verify that the engine is set at TDC/compression for the No. 1 cylinder. The notch on the crankshaft sprocket aligns with the pointer on the oil seal retainer.
  12. Release and remove the tensioner spring to release the timing belt's tension.
  13. Remove the timing belt.
  14. Unbolt the tensioner pulley bracket from the engine's front cover.
  15. If necessary, unbolt and remove the camshaft sprockets. Use a puller to remove the crankshaft pulley if necessary. Don't loose the crankshaft sprocket key. To install:
  16. Install the camshaft and crankshaft sprockets if they were removed. Align the timing marks and be sure to install any keys. Tighten the camshaft sprocket bolt to 43 ft. lbs. (59 Nm).
  17. Install the tensioner assembly. Tighten the tensioner mounting bolt to 14 ft. lbs. (19 Nm). Tighten the cap bolt to 9 ft. lbs. (13 Nm).
  18. Make sure the crankshaft and the camshaft sprockets are aligned with their timing marks. Install the timing belt onto the sprockets using the following sequence: first, crankshaft sprocket; second, oil pump sprocket; third, camshaft sprocket.
  19. Loosen the tensioner mounting bolt. This will allow the tensioner spring to apply pressure to the timing belt.
  20. After the spring has pulled the timing belt as far as possible, temporarily tighten the tensioner mounting bolt to 14 ft. lbs. (19 Nm). NOTE: Remove the flywheel holder before rotating the crankshaft. Reinstall the holder to torque the crankshaft pulley bolt.
  21. Rotate the crankshaft counterclockwise two complete revolutions to check the rotation of the belt and the alignment of the timing marks. Listen for any rubbing noises which may mean the belt is binding.
  22. Loosen the tensioner pulley bolt to allow the spring to adjust the correct tension. Then, retighten the tensioner pulley bolt to 14 ft. lbs (19 Nm).
  23. Install the lower timing cover and the crankshaft pulley.
  24. Tighten the crankshaft pulley bolt to 87 ft. lbs. (118 Nm). Tighten the small pulley bolts to 6 ft. lbs. (8 Nm).
  25. Install the upper timing cover.
  26. Install the starter if it was removed. Tighten the bolts to 30 ft. lbs. (40 Nm).
  27. Install the power steering pump. If the hydraulic lines were disconnected, refill and bleed the power steering system.
  28. Install the water pump pulley and tighten its nut to 20 ft. lbs. (26 Nm).
  29. Install the cooling fan assembly.
  30. Install and adjust the accessory drive belts.
  31. Connect the negative battery cable.

Jun 26, 2009 | 1995 Isuzu Trooper

2 Answers

Crankshaft Pulley..98 Subaru Forester


just a socket set will do the job.But remove the bolt and put thread lock-tight on the threads and tighten to manufacturers toque

May 30, 2009 | 1993 Buick Park Avenue

1 Answer

Crankshaft pulley


no it doesnt,to undo fit a appropiate socket and using a big knuckle bar wedged in suspension turn starter motor to undoo the bolt

Dec 14, 2008 | 1990 Acura Integra Hatchback

1 Answer

Crankshaft pulley (vibration damper) moved forward.


the pulley is also a dampener often times they seperate from each other. replace pulley/dampener.

Nov 18, 2008 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...