Question about 1996 Ford Probe

1 Answer

Front Exhaust Manifold

I'm looking to find a part for a 1996 Ford Probe GT 2.5 L. Part # F4209430A, and it's called Front Exhaust Manifold considered a catalytic converter, but not the real rear catalytic converter but one based right in the manifold itself. Does anyone have any help.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I have one i can sell and ship to you, call me at 218-435-1122

Posted on Aug 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Two codes


code p1443 - Evap canister purge system mafunction.possible cause faulty Evap canister purge valve.fuel vapor hose blocked between Evap purge valve and the FTP sensor or blocked between purge valve and intake manifold or vacuum hose blocked between purge valve and intake manifold.code po430 catalytic system efficiency bank 2 below threshold.possible causes. air leaks at the exhaust manifold or in the exhaust pipes. catalytic converter is damaged.ECT OR CHT SENSOR has lost its calibration.engine cylinders misfiring or the ignition timing off.engine oil is contaminated.front HO2S or rear HO2S is contaminated with fuel or moisture.both front HO2S OR REAR HO2S is loose in mounted hole. fuel pressure is too high due to faulty fuel pressure regulator.

Jan 02, 2013 | 1996 Ford Thunderbird LX

1 Answer

How many oxygen sensors are there on a 1996 ford explorer 8 cyl., 4.0 eng.


The answer depends on the type of exhaust system you have. You will have either 3 or 4 total O2 sensors on your V8. If you have single exhaust with a single catalytic converter then you will have 3 O2 sensors (2 upstream sensors & one downstream sensor - "up or down stream" meaning before of after the catalytic converter). If you have either dual exhaust and/or two catalytic converters then you have 4 O2 sensors (2 upstream & 2 downstream). If you have an MIL light (malfunction indicator light, or "check engine light") the code will indicate "front bank / bank one", which is one of the 2 upstream O2's before the catalytic converter(s), or "rear bank / bank two", which is one of the O2's after the catalytic converter(s).

Apr 22, 2012 | 1996 Ford Explorer

1 Answer

Where does the catalytic converter go


It is usually about three feet from the exhaust manifold. There should be the exhaust manifold an exhaust pipe that goes from the exhaust manifold and curves under the car to about right under the front seats. Then the catalytic converter.

Feb 08, 2012 | 2001 Ford Taurus

2 Answers

Where do we find the o2 sensor on a 99 ford expedition?


there is actually 4 o2 sensors all located in the exhaust, one on each manifold or just after the manifold and then there is one before the catalytic converter and one after it

Feb 14, 2011 | 1999 Ford Expedition

2 Answers

Where are the front 02 sencers located


There are 4 oxygen sensors on the Windstars They are divided into 2 banks of 2.
- Bank 1 is the for the rear 3 cylinders of the engine
- Bank 2 is for the front 3 cylinders.

Bank 1 / Sensor 1 (upstream) is located just below, in the pipe, the exhaust manifold on the back of the engine.

REMOVE TIP: you may have to bend part of the transmission heat shield out of the way - be sure to put it back when done.

Bank 1 Sensor 2 (downstream) is located just past the drivers side catalytic converter. Bank 2 Sensor 1 (upstream) is located just below the exhaust manifold, in the pipe, at the front of the van - access is from the top. Bank 2 Sensor 2 (downstream) sensor is located just past the passenger side catalytic converter.

NOTES: * Use lots of penetrating oil - allow to soak - to make removal easier and avoid damaging the exhaust pipe

* The sensors are screwed directly into the pipe at a 90 degree angle and look like spark plugs with either 8", 12", or 14" wires attached to them

zjlimited_167.gif


Hope this heslps (remember tp rate this answer).

Feb 08, 2011 | 2003 Ford Windstar

1 Answer

What are the torque specs for 1996 Buick Century 3.1 L intake manifold?


Front Pipe REMOVAL & INSTALLATION Pipe Without Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal..
  2. Raise and support the front of the vehicle on jackstands.
  3. Remove the exhaust pipe-to-manifold nuts.
  4. Support the catalytic converter, then disconnect the pipe from the converter. Remove the pipe.
  5. Remove the exhaust gaskets. To install:
  6. Be sure to use all new gaskets when required. Assemble the system, check the clearance and tighten the bolts to about 15-30 ft. lbs. (20-41 Nm). Fig. 1: Front exhaust pipe connection common on vehicles with the catalytic converter not included 86813320.gif

  7. All clamps should be tightened to about 18-25 ft. lbs. (24-34 Nm). Do overtighten the clamps. If pipes become dented they can leak.
Pipe With Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal.
  2. Raise and support the vehicle.
  3. On some vehicles you will need to remove the brace from the transaxle.
  4. Remove the exhaust pipe nuts from the manifold.
  5. Support the catalytic converter pipe bolts from the rear of the converter.
  6. Lower the catalytic converter/front pipe assembly from the vehicle. To install:
  7. Be sure to use all new gaskets when required.
  8. Attach the new catalytic converter/front pipe assembly to the vehicle. Tighten the pipe to manifold nuts to 20-40 ft. lbs. (27-55 Nm).
  9. Attach the bolts at the rear of the catalytic converter/front pipe. Tighten them to 30-35 ft. lbs. (41-47 Nm).
  10. Connect the brace at the transaxle if removed.
  11. Lower the vehicle. prev.gif next.gif

Dec 18, 2010 | Buick Century Cars & Trucks

1 Answer

Where do we find the o2 sensor to replace it on 1996 ford explorer v-6 4.0


Item Part Number Description 1 52 Exhaust Inlet Pipe 2 N803420-S2 Exhaust Manifold-to-Inlet Pipe Bolts
(4 Req'd) 3 5E212 Three Way Catalytic Converter 4 5230 Muffler 5 N620482-S2 Exhaust Inlet Pipe-to-Converter Nut
(3 Req'd) 6 5B266 Exhaust Converter Inlet Pipe Gasket 7 N620481-S2 Nut 8 5E269 Exhaust Converter Frame Bracket 9 N620481-S2 Nut 10 5260 Exhaust Outlet Pipe Frame Bracket 11 5E269 Exhaust Converter Frame Bracket 12 39006 Screw and Washer 13 5E241 Exhaust Converter Outlet Gasket 14 5G215 Exhaust Pipe Flange Hold Down Spring 15 N802641-S2 Nut and Retainer 16 — Rear Heated Oxygen Sensor (HO2S) A — Tighten to 34-46 Nm
(25-34 Lb-Ft) B — Tighten to 20-25 Nm
(15-19 Lb-Ft) C — Tighten to 34-46 Nm
(25-34 Lb-Ft)

ee3a51c.gif

Apr 03, 2010 | 1996 Ford Explorer

1 Answer

Po420" Problems 1996 plymouth van


A code P0420 may mean that one or more of the following has happened:
  • Leaded fuel was used where unleaded was called for
  • An oxygen sensor is not reading (functioning) properly
  • The engine coolant temperature sensor is not working properly
  • Damaged or leaking exhaust manifold / catalytic converter / exhaust pipe
  • Retarded spark timing
  • The oxygen sensors in front and behind the converter are reporting too similar of readings

Some suggested steps for troubleshooting a P0420 code include:
  • Check for exhaust leaks at the manifold, pipes, catalytic converter. Repair as required.
  • Use a scope to diagnose the oxygen sensor operation (Tip: The oxygen sensor in front of the catalytic converter normally has a fluctuating waveform. The waveform of the sensor behind the converter should be more steady).
  • Inspect the downstream heated oxygen sensor (HO2), replace if necessary
  • Replace the catalytic converter

Oct 19, 2009 | 1996 Plymouth Voyager

2 Answers

Looking for a picture of the engine of a 1996 ford probe


no, if the oil pressure is eratic the first thing i would check is the oil pump. unless lots of black smoke is coming out the tail pipe. in that case your engine seals are bad and you will have to do a compleate rebuild on the engine.

Aug 14, 2009 | 1996 Ford Probe

2 Answers

Were is the front oxygen sensor located on a 1996 lincoln tow car


passenger side of manifold, before the catalytic converter. this system may have more than one on the frontside of the cat.

Feb 27, 2009 | 1996 Lincoln Town Car

Not finding what you are looking for?
1996 Ford Probe Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...