Question about 1993 Ford Crown Victoria

1 Answer

Door panel on 1993 Ford Crown Vic

I need to learn how to take off the door panel so i can fix the window which is off track

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I just finsished working on this problem. There are three screws that hold the door panel on. One on the opposite side of the rear-view mirror. Another just below it (seen with the door open) and one in the middle on the bottom. When these three screws are removed, carefully pry the plastic trim from around the door handle. You can use a screwdriver. Then gently slide the panel up.

Good luck.

Posted on Jul 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2007 crown victoria driver side window wont go up or down what's the problem ?


if it is electric window check fuse box or the window motor or the connections or switch

Jan 24, 2016 | Cars & Trucks

1 Answer

Where is the a.c. heater blend door actuator located on a 2005 crown victoria


images for Where is the a.c. heater blend door ...

Fix Heat Door Actuator. - YouTube

? 6:17
https://www.youtube.com/watch?v=NkUPsacbYzc
Oct 7, 2012 - Uploaded by zephmont
My 2005 Crown Vic is blowing out a little heat at times but not how it normally does. .... actuator to press the ...

2003 ford crown vic Heat blender actuator fix - YouTube




Nov 26, 2015 | Cars & Trucks

1 Answer

My 1993 Ford crown vic the driver side door needs to be adjusted is there anyway to do it?


It is possible to adjust the door however you need to be sure that there is no play in the hinges. Open the door and look at the latch and striker (where the latch goes against). If there is wear on either part then the hinges are probably worn. Lift up on the door and check for excessive play. If play is present the hinges should be checked and replaced if necessary. You may be able to adjust the door to the correct position if there is little to no wear in the hinges. The hinge attaching bolts need to be loosened but left snug. A floor jack with padding can be installed under the door for support. Move the door to the desired position and retighten the bolts. It may tke several tries before you get in right. It helps to make the hinges before moving them so that you have a refernce point. Good luck.

Apr 07, 2011 | 1993 Ford Crown Victoria

3 Answers

On my 2000 ford crown vic. the power door locks work except for the drivers side. sounds like something is rattleing in the door. any ideas on what and how to fix


the power lock in that door may have broke the rod. remove the door panel to inspect its operation and replace the necessary part. hope this helps

Jan 31, 2011 | 2000 Ford Crown Victoria

1 Answer

How do i remove the door pannels


remove the screws for the catch all box ot the bottom of door, remove the window switch and the two hex head screws that hold the door panel on under the switch. remove the screws under the arm rest and remove it. When that is done it just un snaps from door

Mar 12, 2010 | 1989 Ford Crown Victoria

1 Answer

2001 Ford Crown Victoria Passenger window will not close.


The window may be off track. Remove the door panel (careful not to break the plastic clips) and attempt to roll the window back up. It it still does not move, you may have a blown window motor for that door. You will be able to lift the window to the closed position if weather is a factor until you get the new motor.

Jan 10, 2010 | 2001 Ford Crown Victoria

1 Answer

How do I remove the inner door panel on a 96 ford crown vic without damage?


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

May 03, 2009 | 1996 Ford Crown Victoria

3 Answers

94 crown vic driver power window does not work can


The window regulator can be broke. Its made of plastic and they break often.

May 03, 2009 | 1994 Ford Crown Victoria

2 Answers

Driver Side Front Window Replacement


You just drop it down from the top at a slight angle. Then put the bolts back in and check to make sure that it moves freely.

Dec 21, 2008 | 1993 Ford Crown Victoria

1 Answer

2004 crown victoria lx smashed driver side window


normally you have to loosen the track and it comes out as one whole assembly stop by a dealer in the parts department and ask them to print out a diagram or show them the part you are having the problem with

Aug 27, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
1993 Ford Crown Victoria Logo

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...