Question about 1991 Mercury Tracer

1 Answer

Ignition We have a 1991 Mercury Tracer that we lost the keys for and we've tried the opening the panel and using the 'screwdriver method' but that doesn't work. We want to hotwire the car so that we can drive it to a mechanic but don't know which wires to use and can't find a diagram anywhere that says which ones are the 'on' wires. Can you help?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

Sadly even if you hotwired it you wouldnt be able to drive it far. The steering wheel would lock up and you wouldnt be able to turn. However you can call a locksmith who can cut you a new key usually right in your own driveway. Normally they dont charge that much as long as you dont ask them to come over at this very second.

Posted on Dec 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1991 mercury tracer. It runs good in park but has no power in drive. What could be the problem?


Sounds like a loose connection or a short somewhere in the wiring harness. Exaimine the wiring with a good light.

Jul 17, 2014 | 1991 Mercury Tracer

1 Answer

How do i change bulb in headlight on mercury tracer? 1991.


1. Open the hood and remove the screws holding the headlight assembly in place. These screws are located on the back side of the headlight assembly.

2. Slide the headlight assembly forward.


3. Unplug the electrical connector running to the headlight ballast.


4. Slide the new headlight assembly and bulb into place, connect the connector to the headlight ballast and secure the assembly with the factory screws.

Feb 24, 2011 | 1991 Mercury Tracer

1 Answer

How do you locate the starter on a 1991 mercury tracer?


its under the intake manifold, best to get at it from under the car. assuming its a 1.8lt

Jan 21, 2011 | 1991 Mercury Tracer

1 Answer

Ignition turns off immediately after turning. wont hold in run is there an easy fix or bypass? 1991 mercury marquis


They get real sloppy the ignition switches on most older fords.....unhook your battery then put the key in the run position and on the bottom of the steering column there is a small hole that is acceess to the release pin for that ignition swich ..you need a small screwdriver of lung thin punch to push that in and your ignition switch just comes our .
Go to the local wreckers or dealer and get a replacemen ........Keep in mind the key will be different from before so make sure the used one comes with a key

Aug 18, 2010 | 1991 Mercury Grand Marquis

1 Answer

91 mercury tracer 4 door sedan stalled while driving... wont start. Changed Spark plugs and wires and ignition coil. spark plugs are getting spark and the car is getting fuel. any suggestions?


You Know in the trunk is a fuel cut off switch i read in the manuel it will trigger even if u hit the smallest bump causing the car not to start before u mess with it please read up on it

Aug 12, 2010 | 1991 Mercury Tracer

1 Answer

Where is the fuel filter located on my car?


It will be on the rail under the car on drivers side

Jun 02, 2010 | 1991 Mercury Tracer

1 Answer

I need to know how to put a trans in a 1991 mercury tracer


OH BOY, THATS A PAIN TO REPLACE. SOME GUYS JUST REMOVE ENGINE AND TRANNY OUT TO MAKE THE PROCESS EASIER. ITS HARD,

Jan 23, 2010 | 1991 Mercury Tracer

Not finding what you are looking for?
1991 Mercury Tracer Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

69014 Answers

Ron Lankford

Level 3 Expert

5383 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...