Question about 1999 Nissan Quest

1 Answer

Cranshaft position sensor

Could you please tell me where the cranshaft position sensor is locate.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It is located on top of the tranny in behind the exhaust manifold..

Posted on Jul 21, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the crankshaft sensor located on toyato yaris 02.thanks

The cranshaft sensor is located behind the pulley at the 7o'clock position

Aug 02, 2017 | Cars & Trucks

1 Answer

Where cranshaft sensor location

Crankshaft Position Sensor is on the engine. Typically near the front or belt/pulley area. 9 out of 10 times near the bottom of the engine very near the largest pulley on the motor. Some vehicles( less than a third) have more than one. The 2nd would usually be located near the coil/coil pack(s) of ignition system.

Apr 24, 2014 | 2000 Jaguar S-Type

1 Answer


The 2002 Santa Fe came with three (3) possible powertrains (engines). The 4 cylinder, and two different V6 engines - i.e. 2.4L 4 cylinder, the 2.7L V6 and the 3.5L V6.

The crankshaft position sensor on the 4 cylinder and the 3.5L V6 are in the same place - Front Crank Shaft behind the pully (behind the timing belt cover.

On the 2.7L V6, the Cranshaft Position Sensor is located in the engine block (Left Hand Side)
near the flywheel (adjacent to the LH (Bank 2) exhaust manifold.

Note: Left Hand Side means the radiator side (front) Bank 1 is the firewall side.

Jun 30, 2011 | 2002 Hyundai Santa Fe

2 Answers

How do check the CPS on a 2000 Ford Explorer?

you cannot check crankshaft postion sensor if your car has hard starts or does not start your crankshaft postion sensor is faulty it tells cars pc when to fire spark and to what cylinder to fire it to

if it helps please leave a 4 thumbs review if it helps

May 10, 2011 | 2000 Ford Explorer

3 Answers

Truck died while driving on interstate. turns over but will not start. is a 1996 ram 1500 V6, 3.9L

Hi, suspect a fuel delivery issue. first check for fuel, then check for spark.

Please see my tip at . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Jan 01, 2011 | 1996 Dodge Ram

1 Answer

How to install a cranshaft position sensor on a 2007 chevrolet malibu


the cam shaft positioning sensor is where the distributor used to be. the cam turns the probably dont have a distributor and now there is a cam position sensor in its place. assming you have distributerless ignition,and coil packs.

if it has a distributor, the sensor is located under the rotor and is held by 2 screws, but in order to remove it, you have line up the the notch in the mounting plate for the rotor with the sensor or you wont be able to get it out, its a very tight fit.

Best regards.

Oct 29, 2010 | Chevrolet Malibu Cars & Trucks

1 Answer

Where is cranshaft position senser on 97 nissan pathfinder

The Crankshaft Position Sensor (CKP) is mounted on the top of the transmission bell housing. Assuming you are talking about the 3.3L V6.
The crank position sensor (ckp) is located at the back of the motor,driver's side, mounted to the transaxle housing. It gets it's single from the flywheel teeth. First unplug it and then remove the retaining bolt and pull it up and out. Reverse precedure to install.

Sep 29, 2009 | 2000 Oldsmobile Alero

2 Answers

We can not find the cranshaft position sensor on

should b on the driver side center bottom of axel

Sep 01, 2009 | Dodge Stratus Cars & Trucks

2 Answers

2001 concorde dont start

Check the cranshaft position sensor located under the timing cover. Also check the camshaft sensor located near the camshaft.

Feb 06, 2009 | 2001 Chrysler Concorde

1 Answer

No Spark: Were is the cranshaft sensor located?

The crankshaft position sensor is located on the bell housing (forward area of transmission where torque converter is located). It can be reached from below (driver side). It has one wire plug in, and one (maybe 2) mounting bolts.countrycurt0

Aug 03, 2008 | 1988 Jeep Cherokee

Not finding what you are looking for?
1999 Nissan Quest Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

78267 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides