Question about 1998 Toyota Camry

1 Answer

Rear seatbelt How do I remove the left, rear seatbelt? Tension spring is not working.

Posted by on

  • 7 more comments 
  • olden bitter Jun 26, 2008

    it's a 1998 Camry

  • Anonymous Jul 21, 2008

    Same problem

  • Anonymous Aug 11, 2008

    Yes I have the same problem. A few years ago it was the right hand side and a panel beater fixed it on the cheap, But I havent been able to figure out how to fix this one. Apparently you need to replace the whole mechanism.

  • Anonymous Aug 28, 2008

    seatbelt doesnt roll back after use. what i already try was removing the seatbelt and tried to rewind the spring but that fail.

  • pooppy Sep 12, 2008

    Same problem!

  • DAFFY42 Oct 23, 2008

    How do you replace the rear seatbelt yourself if the spring doesn't work anymore?

  • yytt Nov 22, 2008

    I have the same problem on right side. The seat belt won't retract.

  • Anonymous May 16, 2009

    I have the same problem. 2000 Camry right rear seat belt.

  • Anonymous May 16, 2009

    me too

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

Yes, you need to replace the whole assembly once the tensioner gives out.

Posted on Aug 17, 2008

2 Suggested Answers

  • 160 Answers

SOURCE: rear seatbelt

fold rear down take outter seat off one twelve bolt at bottom remove clps and pck tray YOU GOT IT

Posted on Mar 16, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The back left seat seems to be stuck due to the locking of the middle seatbelt. Any idea on how to fix that?


When a seatbelt locks up it is usually due to dirt or corrosion in the automatic locking mechanism. The mechanism can't release because it is under tension. If you get into the cover that houses the release mechanism for the seatbelt, you may be able to hit it with a little wd-40. You do have to release that tension so that the lock will spring back to the open position and allow the seatbelt to retract. Try the lube. Sometimes the galvanized coating on the internal parts causes a seize.

Apr 07, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

How to remove and clean and replace the rear brakes on a 2008Toyota yaris


REMOVING REAR BRAKE DRUM SUB-ASSEMBLY
1. Release the parking brake and remove the rear
brake drum.
If the rear brake drum cannot be removed easily,
do the following:-
2.Remove the hole rubber and insert a screwdriver
through the hole into the backing plate, and hold the
automatic adjust lever away from the adjuster.
3.Using another screwdriver, contract the brake shoe
by turning the adjuster.
4. Take out the brake drum from the flange.
5. remove the shoe hold down spring cup, shoe hold down spring, pin and front side brake shoe.
6. Remove the tension spring. Remove the shoe return spring from the rear brake shoe and remove the parking brake shoe strut set.
7. Remove the shoe holding spring cup, shoe hold spring, pin and rear brake shoe.
8. separate the parking brake cable.
9. Remove the automatic adjust lever tension spring and remove the automatic adjust lever.
10. remove the C-washer and remove the parking brake shoe lever.
NOTE: Do not use any solvent like gasoline to wash the brake parts.
Always wear safety goggles and mask before using compressed air.



Dec 28, 2013 | Cars & Trucks

1 Answer

2002 Mazda Protege5. While changing rear struts, the rear seatbelts had to be unmounted. I allowed the seatbelt to retract and now it will not extend (only retracts/takes in) far enough to mount it back....


Hi, these retractors or sensitive to direction so that if the are not sitting properly they will not release. as if in a roll over situation. try holding the retractor at the angle at which it was mounted and then apply slight tension on the belt pulling out. Don't take the plastic covers off or the spring inside will come a part and you will be buying new belt assembly's

Aug 27, 2010 | 1999 Mazda Protege

1 Answer

How do I take the strut off the rear of a 92 LincCont? There is this spring deal that fits into a bracket on the strut and its tremianl ends are coiled and affixed to the sway bars. Are these springs under...


if the strut is through the center of the spring yes it will have tension on the spring remove the three nuts off the top of the strut mount plate unbolt it from the sway bar and spindle (removing any brake hoses or wires attached of course) remove from vehicle. there are spring compressors that have 2 hooks and a large bolt to draw off the spring tension you could probley borrow them from any local parts place with the tension released unbolt strut dont attempt to remove strut without taking the tension off could end up nasty!!!

Feb 25, 2010 | 1992 Lincoln Continental

2 Answers

Subaru legacy 93 retractable seatbelts work then dont work wat is the cause of this?is the tract dirty or something?


Are both right and left sides inop? Check the switches on the door jams. They could be going bad.Make sure they are working. Check the motors that retract the belts.

Jul 26, 2009 | 1993 Subaru Legacy

1 Answer

I have a 94 jeep wrangler front left axle seal bad. I took the left side apart and not sure how to get the seal back in. Do I need to open the inspection cover on the diff. and take the gears out?



Rear Axle Notes
  1. Raise and support vehicle.
  2. Remove rear wheels.
  3. Scribe alignment marks on propeller shaft and axle for proper assembly, then disconnect propeller shaft from axle.
  4. Disconnect the track bar from axle mounting bracket.
  5. Disconnect parking brake cable at equalizer.
  6. Disconnect shock absorbers at axle tubes.
  7. Disconnect hydraulic brake hose at rear axle Tee-fitting, then tape ends of hose and fitting to prevent contamination.
  8. Disconnect axle vent tube from axle.
  9. Remove U-bolts and tie plates.
  10. Loosen spring mounting bolts.
  11. If equipped, disconnect ABS wiring connections at axle.
  12. Support axle with suitable jack.
  13. Remove spring-to-shackle attaching bolts and lower spring to the floor.
  14. Remove axle assembly.
  15. Reverse procedure to install.

Front Axle Notes
  1. Raise and support vehicle at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Jul 21, 2009 | 1994 Jeep Wrangler

1 Answer

Remove and replace rear brake shoes on 2004 honda accord


Brake Shoes Removal & Installation To Remove:
  1. Raise and safely support rear of vehicle.
  2. Remove rear wheel assemblies.
  3. Release parking brake.
  4. Remove brake drum.
Rear brake shoe assembly


6c57c70.gif
  1. Using an appropriate brake spring tool, unhook upper return spring from rearward brake shoe.
  2. Push retainer springs IN and turn to remove tension pins.
  3. Lower brake shoe assembly and remove lower return spring.
  4. Remove brake shoe assembly from back plate.
  5. Disconnect parking brake cable from lever and remove brake shoe.
  6. Remove parking brake lever from brake shoe.

To Install:

d36458c.gif
  1. Install parking brake lever to rearward brake shoe.
  2. Secure lever to brake show with a NEW U-clip.
  3. Pinch U-clip closed.
  4. Connect parking brake cable to rearward brake shoe.
  5. Install self-adjuster lever spring on front brake shoe.
  6. Assemble clevises, adjuster bolt and upper and lower return springs.
  7. Apply a light coat of grease (Molykote 44MA or equivalent) to sliding surfaces.
  8. Install brake shoe assembly onto back plate.
  9. Install tension springs.
  10. Using an appropriate brake spring tool, unhook upper return spring to rearward brake shoe.
  11. Install brake drum.
  12. Install rear wheel assembly.
  13. Lower vehicle.
  14. Adjust self-adjusting brakes by pressing brake pedal several times.

Jul 13, 2009 | 2004 Honda Accord

1 Answer

Rear seatbelt


fold rear down take outter seat off one twelve bolt at bottom remove clps and pck tray YOU GOT IT

Mar 07, 2009 | 1997 Toyota Camry

1 Answer

How to increase the seatbelt pre-tension...2004 f350.


REMOVE THE COVER AND WD-4O THE MECHANISM.THE TENSION IS SET BY A MANUFACTURING PROCESS THAT YOU CANT INCREASE.ALSO IT COULD BE DEADLY TRYING TO DUE TO THE PRESET ACCIDENT LOCKING FEATURE,TRY WD-40 /IF IT WORKS GREAT IF NOT TRY A SALVAGE YARD/NEW PARTS STORE.

Jan 16, 2009 | 2005 Ford F 350 Super Duty

1 Answer

99 maxima rear drivers side seatbelt does not retract.


Inertia reels get stuck permanantly if pulled out suddenly over time or after an accident. You may be able to remove it or pull lightly out with little tension and tap on it, if not you may need to replace the inertia reel.

Jan 06, 2009 | 2000 Nissan Maxima

Not finding what you are looking for?
1998 Toyota Camry Logo

Related Topics:

918 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...