Question about 2004 Chrysler Sebring

1 Answer

2004 sebring How do I reset the oil sensor

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 46 Answers

If you are talking about the change oil message on your cluster. You need to press step until oil change mileage appears on screen and then just press reset.

If you are inquiring about the oil pressure swith on the engine there is no reset procedure. If you just replaced the oil pressure switch and still have no oil pressure, you are going to have to use a manual oil pressure gauge to make sure that you have engine oil pressure. If you have oil pressure with the manual guage there is a problem with the wiring or engine computer.

Posted on Aug 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change oil ressure switch in 2004 chryler sebring lxi 2.7 engine


first off if the oil warning light is on, u need to check the oil pressure with a gauge with the engine at operating temp. and make sure oil pressure is up to spec. a bad switch can cause it to come on also. on the backside of the engine there is an aluminum heat shield covering the switch held on with 3 15mm bolts. after you remove the shield the switch can be removed with a deep socket. dont over tighten the new one when you put it in.

Feb 24, 2015 | 2004 Chrysler Sebring

1 Answer

I have a 2004 Chrysler Sebring Convertable 2.7 Liter. The oil light comes on even after ive just changed the oil. Is there a way to reset it?


Is your oil sending unit bad??? U can reset everything by unhooking the negative battery cable for a few minutes but i dont know if it will help your oil light..Check your connection at the oil sending unit and insure its got a good connection and check for shorts...

Nov 18, 2011 | 2004 Chrysler Sebring

2 Answers

2004 sebring engine light on


If engine is quiet as usual, lots of oil in sump,( Check dipstick)--Usually the light will reset after a certain time period--unless other problem. If over 100,000 miles --have oxygen sensor tested.

Feb 07, 2011 | 2004 Chrysler Sebring

1 Answer

Where is the oil sending unit on a 2004 v6 sebring


The oil pressure sensor is located on the back of the engine, behind a heat shield. you will need to be able to work from under the vehicle to access it.

Jan 20, 2011 | 2004 Chrysler Sebring

2 Answers

2004 chrysler sebring idle speed is too slow. HOw


why do you want your rpms higher while idling? you don't want them high because your gas bill will reflect that. slow shouldn't matter but if it's dying while on idle it could either be your mass air flow sensor or your fuel filter being clogged

Mar 23, 2010 | 2004 Chrysler Sebring

1 Answer

Oil sending unit on 2004 chrysler sebring V6


Should be located close to the oil filter. It will screw in like a spark plug. It has a harness plug. Easy to change, save yourself $70 in labor. You will need a fairly large wrench to remove

Jan 03, 2010 | 2004 Chrysler Sebring

1 Answer

Changed oil and oil light still on


Try disconnecting neg battery cable for 10 minutes, then plug back in. It should reset the code. Otherwise use an obd2 scanner to reset it. If light is still on, the sensor may be bad. You can check with a voltmeter.

Oct 28, 2009 | 2004 Chrysler Sebring

1 Answer

2003 chrysler sebring conv. 2.7 flex fuel, car was running and and all of a sudden it died and would not start. Engine will start if Cam posistion sensor is unplugged but runs rough, did notice sludge when...


Yes it would. But, With no oil Running through it There are a Number of other things that could go wrong. You are on the Correct path Though. Start with the Cam Sensor and see where you are at.

Jan 21, 2009 | 2004 Chrysler Sebring

3 Answers

Oil light??


I was lucky on mine. It was just a bad oil sender switch that needed to replaced, plus the cable connector up-grade. Oil was leaking past the switch. Oil pressure was measured at full spec, both at idel and running.

Dec 27, 2008 | 2004 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Logo

454 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

71288 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7009 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...