Question about 1996 Ford Ranger SuperCab

3 Answers

Head bolt torque for a 1996 ford ranger 2.3liter

Head bolt torque specs

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It is in the haynes repair manuel and chad is right

Posted on Apr 05, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 148 Answers

Tighten first to 26lbs,then go back do 56lbs

Posted on Jul 07, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

The torque specs and tightening sequence can be found in Haynes repair manual #36071.Ford Ranger 1993-2005

Posted on Jun 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for intake manifold on a 1998 ford windstar


what are the torque specs for the head and intake as well as

www.justanswer.com > Ford
... as well as - 47. Find the answer to this and other Ford questions on JustAnswer. ...Intake Manifold Support to RH Cylinder Head, 40-55 Nm. Degas Tube to ...

infamous windstar 3.8L intake gasket - Car Forums and Automotive ...

www.automotiveforums.com > ... > Ford > Windstar
Feb 24, 2006 - infamous windstar 3.8L intake gasket Windstar Car Forums. ... In fact, I may have torqued them in sequence initially to a lower value and then again to the final value in sequence. ... Using the Ford manifold torque pattern pictures can be misleading. ... '96 through '98 use pretty much the same intake.
Intake torque specs ' FordForumsOnline.comwww.fordforumsonline.com > Ford Tech Forums > Engine & DrivetrainMay 7, 2010 - 2 posts - ‎2 authorsISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).Torque Specifications - AutoZonewww.autozone.com/.../Ford-Windstar.../Specifications/Torque-...AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Torque specs for 2008 ford ranger 4x2 front axle


Torque Specifications

Description Nm lb-ft Axle-to-frame bolt 66 49 Axle damper-to-frame bolt 34 25 Brake caliper guide pin bolt 33 24 Differential bearing cap bolt 61 45 Differential housing cover bolt 29 21 Ring gear bolt 122 90 Tie-rod nut 91 67 U-joint spider retainer bolt 19 14 Upper ball joint pinch bolt 48 35

Sep 18, 2014 | 2008 Ford Ranger 2WD

1 Answer

Ford torque specs


depends on size of engine. what size is your engine?

Jun 24, 2014 | 1992 Ford Ranger

1 Answer

Steps to change a valve cover gaket on a 1992 ford ranger


its not very hard at all. once you get the heads off just make sure you follow the proper sequence to tighten the bolts. always remember to tighten from the center bolts out to the end bolts so the heads seat flat and even. and make sure you have the proper torque specs for those head bolts. 1) hand tighten. 2) torque to half of the OEM spec. 3) full torque spec. all of this takes a while to do so be patient.

Sep 27, 2013 | 1992 Ford Ranger

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

What is the torque pressure on cylinder head bolts for a ford ranger 2.3l engine


The torque specs for the head bolts are 51 ft.lbs.then an additional 90-100 degrees(angle).Hope this helps.Good luck.

Dec 10, 2010 | 1996 Ford Ranger SuperCab

1 Answer

Need torque specs for oil pan bolts


torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.

May 17, 2009 | 1997 Ford Ranger SuperCab

1 Answer

Torque specs 7.5 inch rear axle 96 ford ranger


Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Jan 30, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
1996 Ford Ranger SuperCab Logo

924 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...