Question about 1992 Mitsubishi Diamante

1 Answer

ALternator Belt and pulley

Hi. I have a 92 Diamante and I need a diagram of the pulleys. Specifically I need a diagram of the alternator belt and pulley so that I can repair it. Thanks.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

What type of engine do you have

Posted on Sep 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the power steering belt on a 4g13



ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.


REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines


0900c15280037bf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt


0900c15280037bf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Loosen the adjuster lock bolt . . .


0900c15280037bf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the alternator belt from the engine

  1. Loosen the alternator support nut.
  2. Loosen the adjuster lock bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the adjuster bolt clockwise until the proper tension is reached.
  3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT


0900c15280037bfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .


0900c15280037bfb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the power steering belt from the engine

  1. Remove the alternator belt as described above.
  2. Loosen the power steering pump adjusting bolts.
  3. Remove the power steering pump fixed bolt on the rear of the bracket.
  4. Rotate the pump toward the engine and remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the pump until the proper tension is reached.
  3. Tighten the adjusting bolts on the pump.
  4. Tighten the fixed bolt on the rear of the bracket.
  5. Install the alternator belt.

A/C COMPRESSOR BELT
  1. Loosen the tension pulley and remove the belt.
  2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines


0900c15280037bfc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)


0900c15280037bfd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the front undercover.
  2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
  3. Remove the belt.

To install:
  1. Install the belt on the crankshaft and alternator pulleys.
  2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
  3. Tighten the fixing nut to hold the adjustment.
  4. Install the undercover and lower the vehicle to the floor.
  5. Connect the negative battery cable.

POWER STEERING BELT
  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the undercover.
  2. Remove the alternator and A/C compressor belt.
  3. Lower the vehicle and remove the cruise control pump link assembly.
  4. Place the power steering hose under the oil reservoir.
  5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:
  1. Install the power steering pump drive belt.
  2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
  3. Tighten the fixing bolts.
  4. Raise the vehicle and install the alternator and A/C compressor belt.
  5. Install the undercover and lower the vehicle.
  6. Connect the negative battery cable.

3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.

To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

Mar 21, 2013 | 1996 Mitsubishi Mirage

1 Answer

Diagram for 5 pulley belt 98 pontiac transport.


start from bottom crankshaft pulley and ac compressor turn belt tensioner counterclockwise or lift forward then run pulley belt around crankshaft pulley and around AC compressor,run pulley belt around power steering pump then around alternator,once drive belt around alternator you done make sure drive is center of crankshaft pulley and AC compressor pulley.and belt back is center against water pump pulley before releasing the belt tensioner.

Aug 27, 2012 | Pontiac Trans Sport Cars & Trucks

1 Answer

JUST A DIAGRAM OF THE SERPENTINE BELT ROUTE


The diagram can be found here.
Remove the upper fan shroud and aircleaner assemblies for easy access.
To release tension on the belt turn the tensioner pulley nut clockwise and slip the belt off the alternator pulley. To refit the belt route as shown over every pulley except the alternator, once again release the tensioner and fit the belt to the alternator. See that the belt is properly seated over every pulley before restarting the engine.

Nov 11, 2010 | Isuzu VehiCROSS Cars & Trucks

1 Answer

I need a diagram to see were my tension-er is


I don't have the figure for your car, but the below figure shows how to remove the A/C belt.
the other belts should have a simple slot in the bracket for adjusting. If you have more questions, let us know.

6f92dc6.jpg
3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.
To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

NOTE The manufacturer does not provide a torque specification for the bolt that secures A/C tensioner pulley.
  1. Connect the negative battery cable.

Oct 06, 2010 | 1994 Mitsubishi Diamante

2 Answers

I need a routing diagram for the alternator belt on my 92 plymouth acclaim


This might help. 2 belts on here, one for AC, other for rest of pulleys.8ccb572.jpg

Jul 12, 2009 | 1992 Plymouth Acclaim

2 Answers

Need diagram showing how to install belt belt came off need to know how it go on and how to ajust it


first jack up the right front tire side of your car and remove cover under your car motor, so you can see your pulleys from underneath your car, remove black cover where your timing chain belt is thats on the top center between alternator and powersteering pulleys, ok,looking at all your pulleys from your right side of your front end, starting from your top left is your alternator pulley,put belt on it and go underneath the motor mount to your right top powersteering pulley,then go down around the bottom right ac pulley,then to your left bottom crankshaft pulley,the back side of the belt thats on your top alternator pulley wraps around the soft edge pulley thats above your center waterpump pulley,then wrap around the idler pulley that's under your top alternator pulley,then wrap the backside of your remaining belt around the tensioner pulley that's in on your right, under your top ac pulley, use a 13 mm wrench to adjust by turning towards the back of your car so you can slide the belt on

alt ps

soft edge

idler wp tensioner


cs ac

Jul 12, 2009 | 1999 Ford Escort

1 Answer

Alternator removel on a 95 mitsubishi diamante


3.0 SOHC. TURN OFF RADIO. THEN DISCONNECT BATTERY NEGATIVE CABLE.REMOVE AIR CLEANER ASSEMBLY.LOOSEN THE TENSIONER PULLEY.REMOVE ALTERNATOR DRIVE BELT .REMOVE ACCELERATOR CABLE.REMOVE.BRAKE BOOSTER VACUUM HOSE.REMOVE EGR VALVE.REMOVE ALTERNATOR ELECTRICAL CONNECTORS. THEN REMOVE MOUNTING BOLTS THEN REMOVE ALTERNATOR. THE 3.0 DOHC DISCONNECT NEGATIVE BATTERY CABLE.REMOVE SURGE TANK.REMOVE AIR DELIVERY HOSES TO GAIN ACCESS TO THE ALTERNATOR .IF YOU HAVE AIR CONDITIONER .REMOVE THE CLAMP .RAISE THE SUCTION HOSE.USE SOMETHING TO HOLD IT OUT OF THE WAY.LOOSEN TENSIONER PULLEY .AND REMOVE THE ALTERNATOR DRIVE BELT .DISCONNECT THE OXYGEN SENSOR CONNECTOR .DISCONNECT THE ALTERNATOR ELECTRICAL CONNECTORS.REMOVE ALTERNATOR BRACKETS AND MOUNTING BOLTS .REMOVE THE BRACKET AND ALTERNATOR AS A ASSEMBLY.SEPARATE THEM ON A WORK TABLE.

Jul 05, 2009 | 1992 Mitsubishi Diamante

1 Answer

Instructions


Just did mine today.....Jack up the front as high as possible, remove front passenger wheel, put jackstands under car so it doesn't come down on you, remove the plastic inside fender well by taking out the 2 bolts and 3 plastic toggles, you need to remove the alternator belt to get to the power steering belt so loosen the center nut on the idler pulley/tensioner and then loosen the idler using the bottom nut/bolt to take the tension off the belt, remove the alternator belt first drawing a picture of how the belt is routed on all the pulleys for reassembly. Now loosen the 2 face nuts/bolts on the power steering belt idler pulley/tensioner and then use the nut/bolt on it's bottom to take the tesion off the belt and then remove the belt. Reinstall the belt and reverse everything to get it back together. Put on a new alternator belt on while your at it.

Jul 22, 2008 | 2001 Mitsubishi Diamante

2 Answers

All belts came off , 1986 740 gle 4 cly. with air nedd to know diagram


On the 92, the belt closest to the engine goes around the power steering pump, water pump, and crankshaft pulley.

The second belt goes around the alternator and the crankshaft pulley.

The third belt goes around the a/c and crankshaft pulley.

Jun 26, 2008 | 1991 Volvo 740

Not finding what you are looking for?
1992 Mitsubishi Diamante Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...