Question about 1991 Mazda 626

1 Answer

Wheel bearing I'm changing my wheel bearing on my 91 626 gt.but,I cant the wheel hub nut off.is there a special way to get it off?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 405 Answers

I've had that problem a few times myself, here's a few things you can do.

1.) Make sure you have the car in gear, this will keep the wheel assembly from spinning with the nut while you try to loosen it. Be sure the car is jacked up and secured with the e-brake.

2.) Ensure you have the right size socket for the hub nut, and use a long socket extention(breaker bar, the longer the socket extion the more torque you will get on nut) with a heavy duty socket wrench.

3.) If it still won't budge go grab a small blow torch and heat up the nut. You can also try penetrating oil to help loosen the nut. Alot of times if the bearings get really bad before being replaced they can sieze up alot of nuts.

It's a start, good luck and I hope this helps.

Posted on Jun 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change a bearing in 1983 ford f150 4 wheel drive


need special socket from parts store remove allen bolts from front alex, loose first axle nut. with neddle nose pliers pull out tab ring .then loosen second ring bearing will be next might have to wiggle wheel to get bearing to slid out. replace bearing snug first lock-nut against bearing keep track of lock nut with *** on it that one is first then {DON'T OVER TIGHTEN} then put ring with holes on next nake sure *** is in a hole, then tighten last lock ring watch how you take hub off make sure hubs are not locked in. after you are done with vech.in air lock hubs ane rotate tire to make sure front axel {drive shaft} turns . I use super blue wheel bearing. grease I pack my bearings every two years

Jun 05, 2011 | Ford F-150 Cars & Trucks

1 Answer

Where the hell can I get a FREE PDF download for my Ford fusion 2 for the removal and replacement of the rear wheel bearings as well as the torque settings for the final nut after replacement.All the so...


Rear Suspension - Rear Wheel Bearing Fusion 2002.75 (06/2002-)

-Removal and Installation

Special Tool(s)

Installer, Differential Bearing
205-062

Installer, Input Shaft Seal
307-210 (17-041)


General Equipment
Soft faced hammerWooden block

Removal

CAUTION: The brake drum and hub assembly removal in this procedure is for installing a new wheel bearing, not for access to brake system components.

-All vehicles

Remove the dust cap.
Remove the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

-Vehicles with rear drum brakes
Release the parking brake.
Remove the brake drum and hub assembly.
Remove and discard the wheel hub retaining nut.


-Vehicles with rear disc brakes
Remove the brake disc.
For additional information, refer to in this section.

Remove the wheel hub.
Remove and discard the wheel hub retaining nut.


-All vehicles

Remove and discard the wheel speed sensor ring (brake disc shown).
Remove the circlip (brake disc shown).
Using the special tool, remove and discard the wheel bearing (brake disc shown).

-Installation

-All vehicles

CAUTION: Support the wheel hub assembly on the wheel mounting face and not on the wheel nut studs.

Using the special tool, install the new wheel bearing (brake disc shown).

Install the circlip (brake disc shown).

CAUTIONS:

Make sure the wheel speed sensor ring is not knocked, damaged and kept free from metal fragments.

Protect the face of the wheel speed sensor ring with a non-ferrous flat block to prevent damage.

Make sure the wheel hub or brake drum is adequately supported and do not allow it to rest on the wheel studs..

Make sure the wheel speed sensor ring is pressed on slowly and squarely until fully seated.

Do not exceed a maximum load of 10 kN.

Using the special tool, install a new wheel speed sensor ring (brake disc shown).

Vehicles with rear drum brakes

CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the brake drum and hub assembly.
Apply the parking brake.

-Vehicles with rear disc brakes


CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the wheel hub retaining nut.
Install the brake disc.
For additional information, refer to in this section.


-All vehicles
Install the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

NOTE: If the dust cap is damaged a new dust cap must be installed.

Using a soft faced hammer and a wooden block, install the dust cap.


There is no real torque settings for the rear wheels, except to say, do not over tighten or you will stretch the lugs and the will loosen over time.

May 28, 2011 | Ford Fusion Cars & Trucks

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

Is there any special tools required to change front wheel bearing on 2003 mini


you will need a big socket to remove the axle nut--about 20 mm or so. Other than that, I don't think so. Procedures from autozone.com below. it doesn't mention having to press bearing into hub.


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Front wheels Hub nut Brake caliper Rotor ABS sensor Wheel hub from steering knuckle and driveshaft Wheel bearings
To install:
  1. Install or connect the following:

    Wheel bearing into hub Wheel hub to steering knuckle and driveshaft; torque bolts to 41 ft. lbs. (56 Nm) ABS sensor; torque to 6 ft. lbs. (8 Nm) Brake rotor and caliper New flanged hub nut; torque to 134 ft. lbs. (182 Nm)

Oct 05, 2010 | 2003 Mini Cooper

1 Answer

How technical is it to replace a front wheel bearing on a 2005 Pontiac SV6 and can I do it without any specialized tools


you will need a big socket (20 or 21 mm) and 1/2 inch drive to remove axle nut and torque wrench to reinstall. The book DOES call for a special tool to get the hub off the axle, but I have never used one before.


Removal & Installation


  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the wheel drive shaft nut.
  4. Remove the brake caliper and wire aside.
  5. Remove the brake rotor.
  6. Disconnect the electrical connector from the wheel speed sensor.
  7. Remove the wheel speed sensor connector from the bracket by depressing the locking tabs.
  8. Remove the 3 hub and bearing assembly bolts.
  9. Install Wheel Hub Removal tool J-42129 to the hub and bearing assembly in order to remove the hub and bearing assembly from the wheel drive shaft.
  10. Remove the hub and bearing assembly from the steering knuckle.

To install:
  1. Install the hub and bearing assembly to the steering knuckle.
  2. Install the 3 hub and bearing assembly bolts and tighten to 85 ft. lbs. (115 Nm).
  3. Install the wheel speed sensor connector into the bracket until the locking tabs click into place.
  4. Connect the electrical connector to the wheel speed sensor.
  5. Install the axle nut to the wheel drive shaft and hand tighten.
  6. Install the brake rotor.
  7. Use a screw driver or similar tool to stop the rotation of the brake rotor.
  8. Tighten the wheel drive shaft nut to 159 ft. lbs. (215 Nm).
  9. Install the brake caliper.
  10. Install the tire and wheel.

Sep 24, 2010 | Pontiac Montana SV6 Cars & Trucks

1 Answer

How to replace a Jaguar X Type fron wheel bearing


Jaguar 2000-06

Wheel Bearings
Removal & Installation
  1. Remove the brake disc.
  2. Remove and discard the retaining clip. Detach the ABS sensor.
  3. Remove and discard the O-ring seal.
  4. Remove the wheel hub and bearing retaining bolts.
  5. Remove the wheel hub and bearing.
  6. Prior to applying sealer, clean the ABS sensor sealing surface and the ABS sensor aperture sealing surface.
  7. Install a new O-ring seal.
  8. Apply a 2.5mm bead of Loctite Ultra Blue 587 Silicone (RTV) sealer to the ABS sensor sealing surface.
  9. Install a new ABS sensor retaining clip.
  10. Install the hub/bearing assembly. Tighten to 90 Nm.

  1. Remove wheel knuckle.
NOTE When removing the wheel hub from the wheel knuckle the bearing will be destroyed and the bearing inner ring will remain on the wheel hub.
d752c5a.jpg

Fig. Using special tools, remove the wheel hub-X-Type
  1. Using special tools, remove the wheel hub.
  2. Using a suitable tool, remove the bearing inner ring.
  3. Using special tools, remove the wheel bearing.
  4. 2125147.jpg

    Fig. Using a suitable tool, remove the bearing inner ring-X-Type

    ee51ce7.jpg

    Fig. Using special tools, remove the wheel bearing-X-Type

To install:

b506586.jpg

Fig. Insert special tool 204-312 in to 204-309-X-Type
  1. Insert special tool 204-312 in to 204-309.
  2. Support the wheel knuckle on special tools.
NOTE Make sure wheel bearing is correctly orientated with the colored side facing inboard.
  1. Align the bearing over special tool.
  2. Using special tools, press bearing into wheel knuckle.
  3. Change special tool 204-312 to 204-313.
  4. Align the bearing and wheel knuckle over special tool.
  5. Slide wheel hub over the guide and align to the bearing.
  6. Using special tools install the wheel hub.
  7. Install the wheel knuckle.

  8. 5a457fa.jpg

    Fig. Using special tools, press bearing into wheel knuckle-X-Type

    b9fcc3f.jpg

    Fig. Change special tool 204-312 to 204-313-X-Type

    be319f2.jpg

    Fig. Align the bearing and wheel knuckle over special tool-X-Type

    8a9e0dc.jpg

    Fig. Slide wheel hub over the guide and align to the bearing-X-Type
  1. Raise front of vehicle and support on stands.
  2. Remove appropriate road wheel.
  3. Using wire or string, secure brake caliper to road spring to take weight off brake hose.
  4. Raise vehicle sufficient to provide access for special tool 204-111.
  5. Install special tool 204-111 in road spring.
  6. Slacken tool adjuster to suit spring length.
  7. Install adaptor and thrust collar.
  8. Position stem of tool in center of spring passing dowel through slot in suspension turret.
  9. 24ce878.jpg

    Fig. Install special tool 204-111 in road spring-XJ Range and XK Range

    1d0063e.jpg

    Fig. Position stem of tool in center of spring passing dowel through slot in suspension turret-XJ Range and XK Range

NOTE When turning tool adjuster, ensure that tool stem does not rotate and disturb position of dowel in suspension turret.
  1. Engage dowel of special tool 204-111 in suspension turret and rotate to position across slot.
  2. Lower vehicle onto stands.
  3. Rotate tool adjuster to tension spring.
  4. Remove wheel speed sensor securing screw and withdraw sensor from vertical link.
  5. Remove nut securing tie rod outer ball joint to steering arm.
  6. Release ball joint from vertical link.
  7. Install special tool 211-098 on tie rod outer ball joint.
  8. Tighten tool bolt to release taper pin from vertical link.
  9. Remove special tool from ball joint and position tie rod for access.
  10. Remove nut securing upper control arm ball joint to vertical link.

  11. 3af9a83.jpg

    Fig. Install special tool 211-098 on tie rod outer ball joint-XJ Range and XK Range

continue...

Aug 03, 2010 | 2002 Jaguar X-Type

1 Answer

Do i need any special tools to change hub bearing on a 95 honda passport


No special tools needed, this Honda has the old type inner and outer wheel bearing's, remove cotter pin, spindle nut slide rotor out, remove wheel bearing, repack new bearing with grease and don't forget to replace grease seal's, install new part's adjust spindle nut and install cotter pin.Good luck,hope this was very helpful.

May 13, 2010 | 1995 Honda Passport

1 Answer

Replacing the right wheel bearing how do u remove that hub do u need a special tool for it


is it a 4x4? the wheel bearing comes with a new hub assembley . Just find out what size the front half shaft nut/ lock nut/axle nut- is. its probably a 33mm thats the only special tool you will need. Unscrew it, take your outer tie rod off the spindle/steering knuckle, theres 3 bolts behind it, take them off then disconect the abs harness and pry out the old hub assembley use a rubber hammer (dead blow hammer) to tap the half shaft out if seized. when installing the new wheel bearing see your manufacturer specs. for torquing the axle nut back on.

Feb 16, 2010 | 2001 GMC Jimmy

1 Answer

2002 ford explorer rear wheel bearing removal


Rear Wheel Bearing
REMOVAL AND INSTALLATION

1. Remove the wheel knuckle.

Wheel Knuckle
REMOVAL AND INSTALLATION

CAUTION: Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied.

1. Remove the wheel and tire assembly.

NOTE: Have an assistant press the brake pedal to keep the axle from turning.

2. Remove the nut and washer and discard the nut.

3. Remove the parking brake shoes.

CAUTION: Do not damage the boot while separating the toe link from the knuckle.

4. Remove the nut and bolt and separate the toe link from the wheel knuckle and discard the nut.

CAUTION: Do not damage the boot while separating the ball joint from the knuckle.

5. Remove the nut and bolt and separate the upper ball joint from the wheel knuckle and discard the nut.

CAUTION: Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.

6. Using the special tool, press the outboard CV joint until it is loose from the hub.

7. Remove the nut and bolt and the wheel knuckle, hub and bearing as an assembly and discard the nut.

(Return to)
Rear Wheel Bearing
REMOVAL AND INSTALLATION

2. Remove the three bolts.

CAUTION: Make sure that the press adapter outside diameter is slightly smaller than the hub outside diameter or damage to the knuckle will result.

3. Using a suitable press, remove the hub from the bearing and discard the hub.

NOTE: The retainer ring is tapered and must be installed flat side down.

4. Remove and Discard the retainer ring.

5. Using a suitable press, remove the bearing from the wheel knuckle and discard the bearing.

CAUTION: The hub and bearing cannot be reused after disassembly.
To install, reverse the removal procedure.

Jan 24, 2010 | 2002 Ford Explorer

1 Answer

Replace front right wheel bearing assembly on a 2001 ford taurus


please rate as solved if this helps

SECTION 204-01: Front Suspension 2001 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub
Material Item Specification Rust Penetrant and Inhibitor
F2AZ-19A501-A ESR-M99C56-A High Temperature Nickel Anti-Seize Lubricant
F6AZ-9L494-AA ESE-M12A4-A
Removal and Installation
s1h~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Suspension fasteners are critical parts because they affect performance of vital components and systems and their failure can result in major service expense. A new part with the same part number must be installed if installation is necessary. Do not use a new part of lesser quality or substitute design. Torque values must be used as specified during reassembly to make sure of correct retention of these parts.
  1. Remove the wheel knuckle (3K185). For additional information, refer to Wheel Knuckle in this section.
Wheel Knuckle
Special Tool(s) s1h~us~en~file=st1516a.gif~gen~ref.gif Remover/Installer, Front Wheel Hub
204-069 (T81P-1104-C) s1h~us~en~file=st1517a.gif~gen~ref.gif Adapter, Wheel Hub
205-237 (T86P-1104-A1) s1h~us~en~file=st1515a.gif~gen~ref.gif Installer, Halfshaft
204-067 (T81P-1104-A) s1h~us~en~file=st1518a.gif~gen~ref.gif Remover, Wheel Stud (Metric)
204-085 (T83P-1104-BH1) s1h~us~en~file=st1263a.gif~gen~ref.gif Remover, Steering Arm
211-003 (T64P-3590-F) s1h~us~en~file=st2461a.gif~gen~ref.gif Adapter for 211-S200
211–211 (T96P-3010–A1) s1h~us~en~file=st1106a.gif~gen~ref.gif Remover, Tie-Rod End
211–001 (TOOL-3290–D) or equivalent
Removal
s1h~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Suspension fasteners are critical parts because they affect performance of vital components and systems and their failure can result in major service expense. A new part with the same part number must be used if installation is necessary. Do not use a new part of lesser quality or substitute design. Torque values must be used as specified during reassembly to make sure of correct retention of these parts.
All vehicles
  1. s1h~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Discard the wheel hub retainer (3B477). It is a torque prevailing design and cannot be reused. If loosened, the retainer must be removed and a new one installed.
    NOTE: Make sure the steering wheel is in the unlocked position.
    Remove the hub cap or wheel cover, the wheel hub retainer, and the washer. Discard the retainer.
  1. Remove the front brake disc. For additional information, refer to Section 206-03 .
  1. Remove and discard the cotter pin and nut.
  1. s1h~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the tie-rod end boot when installing the special tool.
    NOTE: Remove the adapter from the ball end of the special tool. Apply a small amount of grease to the tie-rod end stud and the ball of the special tool.
    Using the special tools, disconnect the tie-rod end.
Vehicles equipped with ABS
  1. Remove the bolt and detach the ABS sensor.
  1. Unclip the ABS sensor wire retainer and position the sensor out of the way.
All vehicles
  1. Remove and discard the nut.
  1. Remove and discard the nut.
  1. Using the special tools, disconnect the ball joint from the lower arm.
  1. Using a pry bar, push the lower arm down until the ball joint is free of the arm.
  1. s1h~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow the halfshaft to move outboard. Over-extension of the tripod CV joint can result in separation of internal parts, causing failure of the halfshaft.
    NOTE: Hold the threaded rod while turning the nut.
    Using the special tools, press the halfshaft from the wheel bearing and hub. Wire the halfshaft in a level position.
  1. Remove the flag bolt and the knuckle.
  1. If necessary, remove the wheel hub and bearing. For additional information, refer to Wheel Bearing and Hub in this section.
  1. s1h~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care not to damage the knuckle or dust shield when drilling out the rivets.
    If necessary, remove the dust shield.
    1. Using a 5.5 mm (0.22 in) drill bit, drill out the rivets. If a larger bit is needed, do not use a bit larger than 6 mm (0.24 in).
    1. Remove the dust shield.
---------------------------------------------------------------
  1. s1h~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The wheel bearing and hub is not pressed into the knuckle. Do not use a slide hammer or strike the inner race of the bearing. Damage to the bearing can result.
    NOTE: If necessary, lubricate the knuckle and bearing with rust inhibitor meeting Ford specification.
    Remove the bolts and the wheel hub and bearing (1104). Discard the bolts.
  1. s1h~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The knuckle bore must be clean enough to allow the wheel bearing and hub to seat completely by hand. Do not press or draw the wheel hub and bearing into place.
    Clean and inspect the knuckle bearing bore. If the knuckle is cracked, install a new knuckle.
  1. Lubricate the knuckle bearing bore with anti-seize lubricant meeting Ford specification.
  1. To install, reverse the removal procedure.

May 16, 2009 | 2001 Ford Taurus

Not finding what you are looking for?
1991 Mazda 626 Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...