Question about 1994 Ford Mustang

1 Answer

Aode selector shaft seal

Can the seal be replaced from the outside

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

No you need to go inside big job call local junk yard for a tranny

Posted on Jul 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Aode-w transmission manual


I hav a 95 Ford Mustang gt with an AODE rebuilt tranny, all internals have been upgrated. I have gears with the exception of overdrive, what could possibly caused this other than a loose overdrive band?

Apr 15, 2013 | Ford F-150 Cars & Trucks

1 Answer

Skoda gear selector assembly manual gearbox 1998 felicia please show design and possible solution to oil leak from gear box end


Normally there is a seal of sorts here (it may be a felt seal or a rubber flap) but I find that if there is a problem here I check firstly the oil level in the gear box and the viscosity of the oil in the box Remove the filler plug (plug in the side of the box ) and drain until oil is level with the bottom of the threads. Best replace oil with a known viscosity oil for you gear box.

Apr 01, 2013 | Skoda Cars & Trucks

1 Answer

HAVE A 1989 FORD F-150 WITH AUTO TRANS THAT YOU CAN'T SHIFT OUT OF THE "PARK" POSITION AT THE STEERING COLUMN. THE TRANY CAN BE SHIFTED AT THE TRANS WHEN LINKAGE IS DICONNECTED.I THINK THE...


What trans? AOD? This is 1992 F Series, all I have.

Shift Controls, Automatic Transmission The transmission shift control linkage or cable transfers the transmission operating mode from the selector lever to the transmission. The indicated transmission position on the steering column is transferred to a shift lever on the bottom of the steering column. On vehicles equipped with cable-operated shift systems, the indicated position of the transmission selector lever is transferred to the transmission through the shift cane, then to the cable, and down to the transmission manual shift lever at the transmission. On vehicles equipped with shift rod assemblies, the rod transfers the indicated transmission selector level position through a bell crank assembly to a control rod. The control rod transfers the indicated position to the transmission assembly.
----------------------------------------------
Automatic Transmission Manual Linkage Adjustments
  1. With the engine stopped and the parking brake applied, place the transmission selector lever at the steering column in the D (DRIVE position) for C6 applications and in the (D) (OVERDRIVE position) for AOD and E4OD applications, and hold against the D or (D) stop by applying a three-pound force to the selector lever knob.
  1. Loosen the shift rod adjusting nut at point A. Refer to the following illustrations.
  1. Shift the manual lever at the transmission into the (D) (overdrive) position for E4OD, by moving the lever all the way rearward, then forward two detents.
  1. With the selector lever and transmission manual lever in the(D) position, tighten the nut at point A to 17-24 Nm (12-18 ft-lb) torque. Use care to prevent motion between the stud and rod.
  1. Remove the three-pound force from the steering column selector lever knob.
  1. Operate the shift lever in all positions to make certain that the manual lever at the transmission is in full detent in all gear ranges. Re-adjust the linkage if required.
  1. On F-Super Duty Chassis Cab and Motorhome and Commercial Chassis recheck for correct operation of the automatic transmission selector indicator (PRN(D)21). Refer to Section 11-04A, Steering Column, Shift Rod Within Tube. ani_caut.gif CAUTION: Under no circumstances will it be permissible to adjust linkage in any position other than the(D) position for E4OD applications.
---------------------
Automatic Transmission Shift Cable Adjustment
  1. From inside the vehicle, place the column shift select lever in the DRIVE position (C6) of the OVERDRIVE (AOD and E4OD). Hang a three-pound weight on the selector lever.
  1. Raise vehicle on a hoist.
  1. Remove the shift cable from the transmission lever ball stud.
  1. Pull down the lock tab on the shift cable body.
  1. Position the transmission shift lever in the DRIVE position (C6) or the OVERDRIVE position (AOD and E4OD). This is three detents from the front-most lever position with the first position counting as one.
  1. Connect the cable end fitting to the transmission lever ball stud.
  1. Push up on the lock tab to lock the cable in the correctly adjusted position.
  1. Lower vehicle down from hoist and remove the three-pound weight from the column shift select lever.
  1. After making the adjustment, check for park engagement. Check the transmission control lever in all detent positions with the engine running to make sure correct detent/transmission actions. Readjust if necessary.

Jun 21, 2011 | Ford F-150 Cars & Trucks

1 Answer

I have a leak coming from inside the bell housing of my transaxle leaking onto my clutch making it slip new clutch replaced less than a week ago and rear main seal replaced oil smells like gear oil (rotten...


There is an oil seal on the gearbox/transaxle input shaft. If this has failed it will leak oil on to the clutch.It might be able to be replaced by just removing the gearbox again to access the seal. Most likely though is, the gearbox will need to be opened up to replace it.

Oct 12, 2010 | 1998 Suzuki Swift

2 Answers

P0705 Trans Range Sensor Circuit Malfunction PRNDL Input


I would check the neutral safety switch. It's located on the shift shaft of the transmission and is known to go bad

Sep 18, 2009 | 2003 Ford Mustang

1 Answer

To replace front axle shaft seal on 1995 f-350 4x4 is it required to open the front differential cover, or can it be done by working from the outside. By removing the brake caliper and hub assembly, will...


Most oil seals are just pressed in from the outside. I've removed oil seals by using a small Allen wrench to hook the seal and pull it out.

Aug 13, 2009 | 1995 Ford F350

1 Answer

Ford Escort Oil Leak on selector shaft


usually an "O" ring where the shaft comes out of the box but if the shaft is worn where the seal runs you may have to replace the shaft

May 07, 2009 | 1996 Ford Escort 4 Door

1 Answer

Leaking Tcase after replacing seal?


If you did not damage it during install, you may have a bad output bearing which is allowing shaft to move up & down, check shaft to see if it moves. Generally unless there is a pronounced groove in the yoke seal surface it will not leak. (I generally put a small amount of rtv black on outside of seal to prevent any seepage around outside.

Apr 15, 2009 | 1989 Jeep Grand Wagoneer

1 Answer

To replace the manual transmission selector shaft seal


You unfortunately have to strip the gearbox, because although the seal is fitted from the outside, the selector shaft has to come out first, and what it's connected to inside can't be undone after gaining access from the plate with 3 bolts on the LH side of the box. The bolt you need to undo is on the RH side of the selector shaft INSIDE the box.

Mar 10, 2009 | 1994 Suzuki Swift

Not finding what you are looking for?
1994 Ford Mustang Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...