Question about 1992 Mitsubishi Mighty Max

1 Answer

Mitsubishi mighty max pick up 1992

Why do you think my high beam lights dont work if my dimmer works and the passing light feature works?

Posted by on

  • Anonymous Mar 13, 2014

    1992 mighty max

×

1 Answer

Something keeps draining the battery in my 1992 Mighty Max pick-up. Does anybody have any suggestions?

Posted on Oct 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I go about manually resetting the maintenance required light on my 2.4L 1992 Mitsubishi Mighty Max pickup truck?


When service to the emission control system has been completed slide the switch to the opposite position, turning off the warning light.
If the service was for the 120,000 mile interval remove the warning light bulb.

CAUTION: If the speedometer is to be replaced set the odometer to the same reading as the odometer being removed. (consult your local motor vehicle laws)



c552c5ee-ba20-417e-87d4-1370e6e09690.gif

Aug 25, 2013 | 1992 Mitsubishi Mighty Max

1 Answer

Cant find headlight fuse 1992 chevy suburban


If the high beam lights work by pulling on the dimmer switch, you are bypassing the headlight switch.
There should be a circuit breaker inside the headlight switch which could be faulty.

Feb 09, 2013 | 1992 Chevrolet Suburban

2 Answers

97 grand marquis high beam stop work but the light well show up on dash that its on but lights dont come on


Does the high beam work on `flash to pass' feature? That's when you pull the lever toward you to flash your high beams.
If they light up while you pull your lever, it's probably a bad headlight connection at the switch on the dash,OR a bad headlight switch(very expensive if it has the delay feature,which most of them do.
If your lghts DON'T brighten when you pull the lever toward you,it might just be bad bulbs......one goes out and you don't notice it, and then when the other goes out,you NOTICE it. don-ohio (:^)

Jan 21, 2013 | Mercury Grand Marquis Cars & Trucks

1 Answer

Check engine light stays on.i have had the o2 sensor and erg controll solinoid replaced


have you checked all fluid levels...these things are somewhat idiot lights and conceivably on your high kl vehicle you may wish to take the bulb out or disconnect the wire...could be that the monitoring function is not functioning correctly..check the manual or google the things that it monitors

May 26, 2012 | 1992 Mitsubishi Mighty Max

1 Answer

No low beam on 1991 mighty max . New tree switch new lamps ??


you may have a blown fuse check the fuse box to see if any are blown,you may find that HIGH & LOW beam lights are on separate fuses.....hope this helps.......cheers.

Jul 16, 2011 | 1991 Mitsubishi Mighty Max

1 Answer

Looking for the timing mark for a 1992 Mighty Max 2.4L. What is the degree set at with a timing light? Thank you in advance


Hello bojak80,

The basic timing is 5 deg. BTDC. Below is a picture of the timing mark. I hope this helps you.

netvan_74.png

Regards,
netvan

Apr 09, 2011 | 1992 Mitsubishi Mighty Max

1 Answer

I took my 89 mighty max to get smogged. It wouldn't pass for a few reasons. Co2 emissions were outrageously high and also there was no check engine light? Does an 89 mighty max have a check engine light? I...


not sure about engine light as i dont think it has one at this age but the CO2 is caused by either a O2 sensor of which you will only have one in front of the cat or the cat as well is past its sell by date ,Test the O2 sensor with a automotive meter for readings and continuety in the heater circuit ,but as a rule i change both at the same time as a four wire sensor is not a lot of money ,well a universal one isnt anyway and make sure the air filter is clean ,if they argue about the engine check light then go to dealer and ask for a copy of the certificate of homoglonation as this will state if it has a light or not

Mar 07, 2011 | 1989 Mitsubishi Mighty Max

1 Answer

1991 Mitsubishi Mighty Max 2D 4X4 V6 3.0L No Start.


you can get pressure specs from your local parts dept, and check injector signal with a noid light

Apr 23, 2010 | 1991 Mitsubishi Mighty Max

2 Answers

Head lights on 1990 jeep wrangle won't work


Ckeck the headlight connections they are notorious for corroding. Check the ground connection for the lights. Pull your dimmer switch back as if you were flashing a car to pass and see if they work there. If they do you have a dimmer switch problem.

Dec 20, 2008 | 2000 Jeep Wrangler

Not finding what you are looking for?
1992 Mitsubishi Mighty Max Logo

Related Topics:

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...