Question about 1993 Dodge Ramcharger

1 Answer

Help please cant find the camshaft or fuel pump

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hiya dont know much but I do know that the fuel pump in that year are usually in the gas tank....have to pull the hole gas tank.

Posted on Apr 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Toyota Avalon fuel pump won't turn on


check for power to the pump and check the earth connection for the pump. Check if you have a fuel pressure sensor in the fuel manifold and if you have check that it is operational and energising the relay from the ECM

Mar 02, 2014 | Toyota Avalon Cars & Trucks

1 Answer

What would cause a combination of P0304 and P2293 OBD codes on a 2007 Passat 2.0T?


P0204 is miss fire detected on #4 cylinder.

Below is TSB from VW on your problem...a common one.


Technical Product Literature Transaction No.: 2015153/1
MIL ON, DTC P0087, P1093 or P2293 Stored in ECM Fault Memory Release date: Jun 29, 2007
Condition
15 07 04 June 29, 2007 2015153
MIL ON, DTC P0087, P1093 or P2293 Stored in ECM Fault Memory
MIL ON with the following DTCs may be stored in ECM fault memory:
DTC Description
P0087 Fuel Rail / System Pressure - Too Low
P1093 Fuel Trim 2, Bank 1 Malfunction
P2293 Fuel Pressure Regulator 2 Performance

Technical Background
Excessive wear of intake camshaft lobe that drives the high pressure fuel pump. The wear limits maximum pump piston lift, causing fuel rail pressure fluctuations.
The wear on the camshaft lobe can also lead to wear on the base of the high pressure fuel pump cam follower.
Production Solution
Increase surface hardening of camshaft lobe for the high pressure fuel pump
Improved intake camshafts have Part No. 06F109101B.
Service

• Remove the high pressure fuel pump and visually inspect:
1. Base surface of the cam follower -6- in contact with the camshaft lobe.
2. Tip of the high pressure fuel pump plunger.
3. High pressure fuel pump camshaft lobe.

If the base of the cam shaft follower looks like -C- or -D-, no excessive wear is present.
Cam follower and camshaft should not be replaced.
If the cam follower base surface is excessively worn so that its surface is concave -B- or missing -A-, inspect the intake cam shaft lobe for wear.

cam.jpg

If the high pressure fuel pump camshaft lobe shows excessive wear, replace the intake camshaft with Part No. 06F109101B and the cam follower with Part No. 06D109309C, see Group 15 Engine - Cylinder head, Valvetrain in ElsaWeb.

Inspect the tip of the high pressure fuel pump plunger for excessive wear.
If excessive wear is found the high pressure pump must also be replaced, see Group 20 Fuel supply in ElsaWeb.
Tip:
High pressure fuel pump plunger damage is only possible if the cam follower base has a hole in it and the plunger tip has come in direct contact with the camshaft lobe.
If no excessive wear can be found in the high pressure fuel pump cam follower or intake camshaft lobe, or if the damage is found in camshafts with part number 06F 109 101 B, create a Technical Assistance Contact Ticket under the Concern Type Engine and Engine Electronics in ElsaWeb.
Attach the complete diagnostic log to the contact, and call the VW Technical Assistance Center for further assistance.

Warranty
When procedure applies to vehicles within the New Vehicle Limited Warranty, use the following:
Claim Type: W2
Part Identifier: 1505
Damage Code: 1505 18 _ _ _* 2
Labor Operation:
2.0T FSI engine Use applicable SRT time in ElsaWeb
Diagnostic Time: Actual GFF time expenditure
Claim Comment: Input "As per Technical Bulletin 2015153" in comment section of Warranty Claim.

* Code per warranty vendor code policy.
Required Parts and Tools
Description Part No: Quantity
Intake Cam Shaft 06F109101B 1
Cam Follower 06D109309C 1

No Special Tools required.

Aug 19, 2011 | 2007 Volkswagen Passat Sedan

1 Answer

My pontiac sunfire just turn off when i was driving .I cant trun it back on...


WELL COULD BE FUEL PUMP. STOPPED UP FUEL FILTER,WATER IN THE FUEL.FAULTY IGNITION MODULE.FAULTY CAMSHAFT SENSOR,FAULTY CRANKSHAFT SENSOR.FAULTY IDLE SPEED CONTROL. MANY THINGS CAN CAUSE VECHICLE TO SHUT DOWN. BEST TO HAVE VECHICLE SCANNED WITH CODE SCANNER.THAT WAY IT WILL HELP PIN POINT PROBLEM QUICKER SO YOU WONT SPEND LOTS OF MONEY BUYING TOO MANY NEW PARTS.

Dec 27, 2010 | 1998 Pontiac Sunfire

2 Answers

Cant locate fuel pump


the fuel pump is located inside the fuel tank, the fuel tank must be removed to change the electric fuel pump.

Apr 26, 2010 | 1995 Mitsubishi Mighty Max

1 Answer

MY 1994 HONDA ACCORD WONT START THE D4 LIGHT COMES ON IVE CHANGED THE MAIN RELAY SWITCH,AND THE FUEL PUMP.BUT I STILL CANT HEAR THE FUEL PUMP TURN ON. WHY?


Check to see if you have spark to your spark plugs. On hondas if you have no spark it wont let the fuel pump get power. This is controlled by a small part in the distributor called the ignitor by honda and ignition module in aftermarket terms. when this part goes bad you wont have spark or fuel. it is a pretty expensive part. sometimes its cheaper to get a used distributor at the junk yard and change the whole thing. also make sure your timing belt hasnt snapped cause if it did your distributor wont turn and you will get the same results. take the distributor cap off and check and see if the rotor spins while someone is cranking the engine. if it doesnt turn your timing belt is broke or your camshaft broke in half. broken camshafts are a common problem with 95 accords. If none of this helps you may have a wiring problem or even your cars computer may have taken a dump

Oct 30, 2009 | 1995 Honda Accord

1 Answer

I need to replace the fuel pump in my 1985 Chevy S10 pickup, need all help. What is the procedures?


EXACT PROCEDURE ! Please Rate Me Fairly for this!! Thank you And Good Luck !!


ELECTRIC PUMP

REMOVAL
  1. Before servicing the fuel pump the fuel system pressure must be relieved. See: Fuel Pressure Release
  2. Disconnect the negative battery cable.
  3. Raise the car on a hoist.
  4. Remove the fuel tank. See Fuel Tank / Service and Repair.
  5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
  6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal. NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.
INSTALLATION
  1. Push the fuel pump assembly into the attaching hose.
  2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal. NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.
  3. Install cam lock over the assembly and lock by turning clockwise.
  4. Reinstall fuel tank.
MECHANICAL PUMP

REMOVAL and INSTALLATION

NOTE: To ease pump installation, rotate the camshaft so the camshaft eccentric is out of the way of the fuel pump rocker arm.

  1. Disconnect fuel lines from fuel pump.
  2. Remove fuel pump mounting bolts and the fuel pump.
  3. Remove all gasket material from the pump and block gasket surfaces. Apply sealer to both sides of new gasket.
  4. Position gasket on pump flange and hold pump in position against its mounting surface. Make sure rocker arm is riding on camshaft eccentric.
  5. Press pump tight against its mounting. Install retaining screws and tighten them alternately.
  6. Connect fuel lines. Then operate engine and check for leaks.

Mar 22, 2009 | 1985 Chevrolet S-10

3 Answers

Stalls while Driving


that'll b air intake system or not enough gas going 2 the engine so it stalls or blocked gas lines

Sep 17, 2008 | 1990 Toyota Celica

Not finding what you are looking for?
1993 Dodge Ramcharger Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...