Question about Chevrolet Silverado 1500

1 Answer

I instal a hood 81 on a Silverado 1/2 ton model 1979

I'snt the same support for the hood,
I'm meet some problem for put
soory i'm TAHITIEN and my english isn't perfect.

Posted by on

  • bear001 May 11, 2010

    could you clarify your question I really can't understand you I will try my best if you can get your point to me, Ok Thanks I hope to hear from you soon



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Expert
  • 58 Answers

Hello , i am sorry to tell you that it is not the same , but i think it can work by some modifications , thank you for using fixya.

Posted on Jun 26, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Will a 4wd transmission fit in 2wd 99 silverado 5.3

I believe it will, but you will have to ensure that they are both the same type, which should be a 4L60E if it's a half ton. You will also have to remove the transfer case and install the tail shaft extension onto the end of the transmission. Also, make sure that they have the same gear ratios. If swapping from a 1/2 ton to a 1/2 ton it should match. If swapping from a 1/2 ton or Tahoe to a 3/4 ton, there may be an issue.

Jan 31, 2017 | Cars & Trucks

1 Answer

Put in new switch, wipers run for awhile and quit

wiper motor is tired, replace. had the same problem with my '81

Apr 06, 2013 | Cars & Trucks

1 Answer

Is my 1995 GMC Sonoma 4x4 a half ton truck

small trucks like that are considered 1/4 ton. silverado 1500 1/2 ton an silverado 2500 3/4 and up. same goes for gmc

Apr 06, 2013 | 1995 GMC Sonoma

1 Answer

Ignition tumbler is noy ingaging 1979 GMC 1/2

the tumblers are jambed
any locksmith will advise to replace the lock cylinder for the part is fairly inexpensive. if repaired it may jamb again very soon. I am a certified locksmith as well

Feb 06, 2010 | 1983 GMC K1500

1 Answer

How hard is it to replace the rear calipers on an 03 silverado 1/2 ton 4 wd and are there any other secrets i should no about

Very easy!! Loosen brake line from caliper, remove two bolts from caliper remove. put new caliper on install bolts, connect brake line, blead air out. Do drivers side first. Same on passenger side,your done.

Feb 02, 2010 | 2003 Chevrolet Silverado Ss

2 Answers

I need to start a 1977 ford truck from under the key and cant get into this possible??460 1 ton dump truck....

Jump wires that would go to ignition, then jump wire from battery to solenoid to turn over.

Aug 27, 2009 | 1979 Ford F 350

1 Answer

Remove the front disc rotor

The rotor and hub assembly are held together by the studs,you must first remove the 4-wheel drive hub assembly,then the wheel bearing nuts,and pull the hub and rotor off as a unit. Next lay it(back down) on a piece of wood, using a drift punch drive the studs out. Turn it over ,lay it(face down) on a block of wood, line the new stud splines up with the grooves in the hub and drive them in with the punch and reassemble. A set of dentist style picks will be helpful with the clip in the 4wd hub and a 4 lug 4wd nut wrench will be needed.

Dec 26, 2008 | 1979 Chevrolet C/K 3500

1 Answer

I have a 1979 Chevrolet pickup 6 cyl 4 wheel drive Silverado, K ½ ton, that has the 5 lugs sheared off of the right front wheel. I am trying to replace them. How do I remove the front disc rotor to get at...

Remove caliper and nut to axle should come of with a little help of a rubber hammer. Knock bolts out from the front and drive new ones in from the back. You can use a lugnut with the flat side down to help pull them in and a hammer to help. Hope this helps.

Dec 26, 2008 | 1979 Chevrolet C/K 3500

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides