Question about 2004 Dodge Intrepid

2 Answers

Camshaft position sensor loacation on a 2004 dodge intrepid

I need to know where it is on the car.

Posted by on

  • frzbman3041 Jan 27, 2009

    Can not find the camshaft sensor location on a 2004 Dodge intrepid anywhere to go to get pics



2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 85 Answers

Cam sensor is located on the timing cover drivers side top

Posted on Jul 02, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

In a 3.5 liter engine,
its under the black plenum ( air intake sit on top of your engine) towards the front , if you look under the plenum to the right of the cooling host and slightly to the left on top of the cam shaft housing slightly to the left

if you get a haynes manual it will show you exactly where but it is not clear but it helps alot of projects

to replace it simply losses the plentum botl on the front and sides it will give you BARELY enough room ! but better than pulling the whole thing off

Posted on Feb 17, 2009

  • df2dot Feb 17, 2009

    CORRECTION: plenum bolts * : )

  • Queen Plummer
    Queen Plummer Oct 03, 2013

    thank you. im a lady im a new driver and just want to learn more about my car. i have change my selenoid before just this january and it was successfully replaced. thank you so much for the help i will check on it now. ^_^



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the camshaft sensor in a 2000 dodge intrepid 2.7 engine

The camshaft position sensor is mounted to the top of the timing case cover. The bottom of the sensor is positioned above the camshaft sprocket. The distance between the bottom of sensor and the camshaft sprocket is critical to the operation of the system.

Jun 30, 2012 | 2000 Dodge Intrepid

1 Answer

Where is the camshaft position sensor on a dodge 04 intrepid

The camshaft position sensor is mounted in the front of the head on 2.7L or belt cover on the 3.5L .

Apr 18, 2011 | 2004 Dodge Intrepid

1 Answer

Where is the camshaft position sensor located on a 2003 dodge intrepid?

Down on front bottom of engine block. Follow the spark plug wires to coil packs and ignition module. Then there will be two or three more wires that run from there down to the crankshaft position sensor.

Jan 16, 2011 | 2004 Dodge Intrepid

1 Answer

I need to know what the diagnostic code 340 means for a dodge 1997 intrepid

A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed
Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

May 22, 2010 | 1997 Dodge Intrepid

1 Answer

Have2004 intrepid shows engine light and error codes po340-& po344

code po 340 no camshaft position sensor signal at powertrain control module and code po344 rationality error detected for intermittent loss of camshaft position sensor circuit. hope this will help you!!!!

Apr 18, 2010 | 2004 Dodge Intrepid

1 Answer

Locate cam position sensor on 2004 dodge intrepid

The camshaft position sensor is mounted to the top of the timing case cover.

Oct 25, 2009 | 2004 Dodge Intrepid

1 Answer

Where is the camshaft position sensor on a dodge intrepid 2003

where is the camshaft position sensor on a 2000 dodge intrepid 2.7L V6

Oct 16, 2009 | 2003 Dodge Intrepid

1 Answer

Stalling,check engine light cam shaft sensor position A code

the code for camshaft sensor is--p0341 and p0342, po341 is camshaft range or performance problem. p0342 is camshaft curcuit , low input. hope this helps carl.

Jul 28, 2009 | 2004 Dodge Intrepid

3 Answers

How can i fix code po344 intrepid 2002

Before replacing the cam shaft sensor,verify good terminal tension and connection at the sensor.This carline has a history of faulty connections here and this could fixya before spending the cash on car parts....good luck

Jul 24, 2009 | 2004 Dodge Intrepid

Not finding what you are looking for?
2004 Dodge Intrepid Logo

2,626 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides