Question about 1998 Mercury Villager

1 Answer

Windshield wipers windshield wiper motor has disconnected somewhere. i took it to a shop and was told, i had to replace the whole motor

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 60 Answers

Most of these windshield wiper motors are located right below the windsheld and above hood. you probably have to undo the louvers where the windshield wiper arms are located and it sits in front of the driver side not too bad to swap yourself part itself is about $60 w/old motor turned in

Posted on Aug 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

2 Answers

How do you replace windshield wiper motor on a 1997 ford e250 van


REMOVAL
  1. Raise and support the hood.
  2. Remove the windshield wiper pivot arms.
  3. Remove the cowl top vent panels.

25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
  1. Disconnect the windshield wiper mounting arm and pivot shaft.
  1. Remove the access cover from the dash panel.
  2. Remove the mounting arm and pivot shaft retaining clip.
  3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
  1. Remove the windshield wiper motor.
  1. Disconnect the electrical connector.
  2. Remove the three bolts.
  3. Remove the windshield wiper motor.
INSTALLATION

25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
  1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
  1. Install the windshield wiper motor.
  1. Place the windshield wiper motor in the dash panel.
  2. Install the three retaining bolts.
  3. Reconnect the electrical connector.

25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
  1. Reconnect the windshield wiper mounting arm and pivot shaft.
  1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
  2. Install the access cover in the dash panel.
  1. Install the cowl top vent panels.
  2. Install the windshield wiper pivot arms.
  3. Adjust the windshield wiper pivot arms.
This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Nov 17, 2014 | Cars & Trucks

1 Answer

Windshield wiper fuse keeps blowing


Since you Disconnect the motor also renewed the switch and is still blowing the fuse ,it is obvious that you have either broken wire between the switch and the motor. Try to test the failure by means of a tester circuit. Good Luck.

Aug 21, 2012 | 2003 Mitsubishi Diamante

1 Answer

My wind shild wiper are not moving but the motor work..


windshield wipers are connected to whats called a Wiper Transmission. Its the unit that actually engages the wipers to the wiper motor. sometimes that disconnects. also some wiper bolts will loosen right at the base of the wiper arm. its rare that both wiper bolts will loosen at the same time. probably the wiper tranmission assembly somewhere has come apart.

Jul 11, 2010 | 1993 Dodge Caravan

1 Answer

I need to replace the windshield wiper motor.


With the wipers at rest, mark their positions on the windshield with a piece of tape or a grease pencil. Remove the small cap on the shaft end of the windshield wipers, just pry it off with a small screwdriver. Then wiggle and pull the wiper arms until they come loose. There are some small clips on the forward edge of the plastic cowl, just pull them forward. Then there are 2 TORX screws, one at each end of the cowl under that rubber flap. Now remove the cowl and set it somewhere you won't step on it. Unplug the electrical connector from the wiper motor and disconnect the linkage. Then you can unbolt the motor and remove it.

May 20, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

Wiper motor replacement


SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the windshield wiper pivot arms (17527).
    1. Remove the nuts (one each side).
    1. Remove the windshield wiper pivot arms.
  1. Remove the LH and RH cowl top vent panels.
    1. Remove the hood weatherstrip.
    1. Remove the screws.
    1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.
  1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
    1. Remove the nuts.
    1. Remove the bolt.
    1. Position the windshield wiper mounting arm and pivot shaft assembly aside.
  1. Remove the windshield wiper mounting arm and pivot shaft assembly.
    1. Disconnect the electrical connector.
    1. Remove the windshield wiper mounting arm and pivot shaft assembly.
----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal
  1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .
  1. Remove the windshield wiper motor (17508).
    1. Remove the output shaft bolt.
    1. Remove the bolts.
    1. Remove the windshield wiper motor.

May 01, 2009 | 1999 Lincoln Town Car

1 Answer

Windshield wipers only work on high setting and do not park


It is the Wiper Motor causing the Problem and will need to be Replaced. They could have caused it by Bumping the Wiper Motor Casing when replacing the Hood or when Working on the Motor. Please Rate my Response, I need all the HelpI can get! Thanks!

Jan 26, 2009 | 1997 Chevrolet Venture

2 Answers

Timing Venture wipers


disconnect the wiper transmission from the motor, then run the motor and turn the motor off with the wiper switch, this will park the motor, re-attach the wiper trans linkage so the wipers are parked/down

Dec 05, 2008 | 2000 Chevrolet Venture

Not finding what you are looking for?
1998 Mercury Villager Logo

556 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...