Question about 2001 Jaguar S-Type

2 Answers

Missing on acceleration

Want to start with plug change, what is best way to remove inlet manifold to access left plugs, gary

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Jaguar 2001 Lower Engine Intake Manifold Gasket how tochhange

Posted on May 19, 2012

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 100 Answers

Remove the air cleaner/intake boot, remove the wipers and upper cowl, remove the crossbeam suport bar (under wiper cowl)
Remove the throttle bosy connectors, remove the bolt on the front lower suport bracket, remove the bolt on the lower side bracket (below intake shock side)
Rthe 8mm nuts on the back where you will see a round black metal bracket, remove the 8 intake 8mm bolts, note they are different sizes, short and long and also they have a rubber washer that sticks to the intake, take care not to loose/drop any of these, especially in the engine.
Life the intake, you dont actually have to remove it completely.
Replace the 2 intake strip gaskets and if it is missing is probably the coil onplug that is bad no the spark plug.
JPTCAT

Posted on Sep 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change plugs on a taurus 20007 3 ltr


remove inlet manifold to gain access to back plugs.

Aug 10, 2014 | Ford Taurus Cars & Trucks

1 Answer

Wgolf.mk4.reg2000.removing upper part inlet manifold.


If you have a 2000 VW Golf 2.0 liter, the answer is yes. Just remove the top part of the intake manifold. A magnet and long handle allen key set will make the job easier for removing/ reinstalling the cap screws. Once manifold off, cover the intake holes with blue painters tape, to avoid dropping any thing down in them. Take care on plug wire removal. Change each plug one at a time. ***Tighten spark plugs with a torque wrench, spec 22 ft-lb in the Bentley manual. AEG, AVH, AZG eng codes***

Jul 08, 2014 | 2000 Volkswagen Golf

1 Answer

Engine diagram


coil 3 on early engines it is under the inlet manifold you have to remove it. you should also change all 3 plugs whilst manifold off the plugs can cause coil failure.we at the dealer I worked for changed all 6plugs and coils on jaguars advise, my advise change coils and plugs under manifold only the other 3 are easy access

Jan 17, 2014 | 2000 Jaguar S-Type

1 Answer

Golf 4 1600 2001 how to remove inlet manifold


there are bolts that hold it in the back for stability so it doesn't crack.

Oct 12, 2012 | Cars & Trucks

6 Answers

Honda Accord 1994 Rough Idle, often miss cylinder 2-3 changed the distributer, the coil, spark plug, spark wire cleaned the egr valve, pcv valve, vaccum I noticed the engine miss the cylinder 2 and 3


Sounds like a dirty Throttle Body and dirty IAC (Idle Air Compensator) valve. Get some good Throttle Body cleaner remove the flexible hose at the Throttle Body spray it and wipe it very very clean an old tooth brush works good for getting in there.

Now remove the IAC from the side of the throttle body, careful with the gasket if you want to reuse it. Spray it down good inside moving the valve back and forth as you do let it soak for a few minutes and clean it again. Blow it out with some compressed air and reinstall it. Put some throttle body/injector cleaner in the fuel tank.

Keep us updated.

Oct 04, 2011 | 1994 Honda Accord

1 Answer

Describe your how fix my pontiac 2000 montana Problem changing spark plugs



Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.


Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the left side spark plug wires from the spark plugs.
  3. Remove the left side plug wires from the retaining clips.
  4. Rotate the engine for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. Remove the right side spark plug wires from the spark plugs.
  6. Remove the plug wires from the retaining clip.
  7. Remove the spark wires from the ignition coils.
  8. Remove the plug wire assembly from the engine.
    NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.

To install:
  1. Install the right side plug wires to the ignition coils and then the spark plugs.
  2. Install the spark plug wires to the retaining clip.
  3. Rotate the engine back to the original position.
  4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
  5. Install the spark plug wires to the retaining clips.

3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the intake manifold cover.
  3. Remove the left side spark plug wires as follows:
    1. Disconnect the left side spark plug wires from the spark plugs.
    2. Disconnect the left side spark plug wires from the ignition coil.
    3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
    4. Remove the left side spark plug wire assembly.

  4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. After rotating the engine, remove the right side spark plug wires as follows:
    1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.

  6. Remove the right side spark plug wire clip from the ignition coil bracket.
  7. Remove the right side spark plug wire assembly.

To install:
  1. Install the spark plug wire assembly.
  2. Install the right side spark plug wire clip at the ignition coil bracket.
  3. Connect the plug wires to the ignition coil and spark plugs.
  4. If the engine was rotated for access, return the engine to the original position.
  5. The remainder of the installation is the reverse order of removal.

Feb 05, 2011 | 2000 Pontiac Montana

2 Answers

Acceleration problems


This firing order diagram would not post in the clarification request for some reason, use this diagram with the information in the clarification request.


0330668.jpg

Jun 19, 2010 | 1997 Cadillac DeVille

1 Answer

I have a 2004 Hyundai Santa Fe with the 6 cyl. engine. I wanted to change the spark plugs. I can get to the front ones easy enough, but the back ones appear to be under the intake manifold. How would I...


don't take the manifold off....... see if perhaps the window wiper dip tray will be enough room to access the rear plugs.....do not remove intake.

Apr 26, 2010 | 2004 Hyundai Santa Fe

2 Answers

How to change an exhaust manifold leak 7.5L


Right-Hand
Removal
  1. Remove spark plug heat shield (12A406).
  1. Remove distributor to spark plug wires (12286) using Spark Plug Wire Remover T74P-6666-A.
    1. Disconnect muffler inlet pipe.
    1. If equipped with secondary air injection, disconnect the secondary air injection check valve tube (9B480).
    1. Remove attaching bolts and right exhaust manifold (9430).
    1. Inspect joint faces for signs fo exhaust leaks, cracks or any defect that would make exhaust manifold unfit for use







Left-Hand Removal






1. Remove oil level indicator tube (6754).
  1. Remove spark plug heat shield.
  1. Remove distributor to spark plug wires using Spark Plug Wire Remover T74P-6666-A.
  1. Disconnect EGR valve to exhaust manifold tube (9D477). If equipped with air injection, disconnect the secondary air injection check valve tube.
  1. Disconnect muffler inlet pipe.
  1. Remove attaching bolts and exhaust manifold (9431).
  1. Inspect joint faces for signs of exhaust leaks, cracks or any defect that would make the exhaust manifold unfit for use.
Installation
  1. Clean mating surfaces of right exhaust manifold or left exhaust manifold and cylinder head (6049). Clean mounting flange of right exhaust manifold or left exhaust manifold and inlet pipe(s). Clean mounting surface for air injection tube or right exhaust manifold. Apply light film of Premium Long-Life Grease XG-1-C or -K or equivalent meeting Ford specification ESA-M1C75-B to right exhaust manifold or left exhaust manifold.
  1. Position right exhaust manifold or left exhaust manifold on cylinder head. Install attaching bolts and washers, starting at fourth bolt hole from front of each right exhaust manifold or left exhaust manifold. Tighten bolts to 34-47 Nm (25-35 lb-ft), working from center right to both ends.
    1. Position inlet pipes to right exhaust manifold or left exhaust manifold. Install attaching nuts and tighten to 34-47 Nm (25-35 lb-ft).
    1. Position the secondary air injection check valve tube and the secondary air injection tube gasket (9C435) at rear of right-hand exhaust manifold. Install attaching bolts and tighten to 19-25 Nm (14-18 lb-ft).
    1. Attach the secondary air injection manifold tube (9B449) to left-hand exhaust manifold fitting (located under EGR tube). Tighten nut to 30-40 Nm (22-30 lb-ft).
    1. Attach the secondary air injection check valve tube to rear of right-hand cylinder head. Tighten bolts to 75-85 Nm (56-62 lb-ft).
      1. Connect EGR valve to exhaust manifold tube to left exhaust manifold, if removed. Tighten nut to 53-72 Nm (39-53 lb-ft).
      1. Install spark plug heat shield and distributor to spark plug wires.
      1. Install oil level indicator tube to left exhaust manifold, if removed. Tighten nut to 13-24 Nm (10-18 lb-ft).
      2. Start engine (6007) and check for exhaust leaks.







b913da4.gif
28b39c6.gif
Hope this helps you...WF †

Mar 10, 2010 | 1996 Ford F250 Crew Cab

1 Answer

Sparkplug changing


you might have to go under the car to access the rear 3 plugs. sometimes you can squeak by and get to them. the side mounted motors can be a little hard to access the rear half of the motor. i would NOT suggest that you remove the manifold though.

Aug 24, 2008 | 2004 Mitsubishi Galant

Not finding what you are looking for?
2001 Jaguar S-Type Logo

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...